Streszczenie treści zawartej na stronie nr. 1
ZMAX-8210 Series
(ZMAX-8210-I/ZMAX-8210-E)
User’s Manual
V2.0.6.0
Streszczenie treści zawartej na stronie nr. 2
Copyright This user’s manual and the software described in it are copyrighted with all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without the written permission of Z-Com Corporation. About This Manual This manual explains Z-Com outdoor ZMAX-8210 Customer Premise Equipment (CPE), how to build the infrastructure centered on the ZMAX-8210 and proposals when u
Streszczenie treści zawartej na stronie nr. 3
Content Chapter 1 Introduction........................................................................................................ 1 INTRODUCTION ........................................................................................................................... 1 APPEARANCE .............................................................................................................................. 1 KEY FEATURES..................................................................
Streszczenie treści zawartej na stronie nr. 4
Appendix A Specifications................................................................................................. 31 Appendix B Technical Terms ............................................................................................ 37 Appendix C ASCII ............................................................................................................. 39 Appendix D SSH Settings.............................................................................................
Streszczenie treści zawartej na stronie nr. 5
Figure Figure 1 ZMAX-8210................................................................................................................. 1 Figure 2 ZMAX-8210 ports........................................................................................................2 Figure 3 Wireless Point-to-Point Outdoors................................................................................. 3 Figure 4 Wireless Point-to-multipoint Outdoors ...................................................
Streszczenie treści zawartej na stronie nr. 6
Table Table 1 ZMAX-8210 Default Factory Settings .......................................................................... 8 Table 2 ZMAX-8210-I Spec..................................................................................................... 31 Table 3 ZMAX-8210-E Spec.................................................................................................... 33 Table 4 Technical Terms ....................................................................................
Streszczenie treści zawartej na stronie nr. 7
Chapter 1 Introduction Introduction Thank you for choosing the ZMAX-8210 Series Customer Premise Equipment (hereafter called CPE). Compliant with the innovative IEEE802.16-2004 and working at the licensed 3.5GHz with efficient modulation, this outdoor CPE gives wireless ISP providers today’s fastest pathway to new markets and revenue. whether well-established and looking to expand, or smaller and newly established – service providers of all types can immediately and cost-effectively crea
Streszczenie treści zawartej na stronie nr. 8
Figure 2 ZMAX-8210 ports The ZMAX-8210 appearance is designed to be water-proof and dust-proof for most challenging environments outdoors. Key Features The ZMAX-8210 provides you with the solid features. Power supply via POE Based on WiMAX together with compliant with 802.16d-2004 Work at 3.5GHz Implement Orthogonal Frequency Division Multiplexing (OFDM） and Non-Line-of-Sight (NLOS) Efficient Modulation Water, dust-proof and built-in antenna for outdoor environments Us
Streszczenie treści zawartej na stronie nr. 9
Figure 3 Wireless Point-to-Point Outdoors Under this structure, the ZMAX-8210 acts as a customer premise equipment (CPE), connecting a WiMAX Base Station. Wireless Point-to-multipoint Outdoors Under this structure, acting as a customer premise equipment, the ZMAX-8210 is connected to the WiMAX Base Station, allowing ISP to cost-effectively build infrastructure in a matter of hours. Chapter 1 Introduction - 3 -
Streszczenie treści zawartej na stronie nr. 10
Figure 4 Wireless Point-to-multipoint Outdoors Typical Case The high-quality performance enables the ZMAX-8210 to gain widespread acknowledgements. It is able to undertake tasks in various situations. Create or expand well-created network via this CPE in enterprises or residential quarters Provide an access to Metropolitan Area Network via WLAN Act as a media connecting Base Station and sub-stations in mobile communicating network Provide an access to hard-to-reach areas, like an
Streszczenie treści zawartej na stronie nr. 11
Chapter 2 Basic Installation System Requirement Before installing the ZMAX-8210 Customer Premise Equipment, make sure your system meets these requirements A PC coupled with 10/ 100Base-TX adapter Configure the computer with a static IP address of 192.168.1.x (x cannot be 1) and 255.255.255.0 for the Subnet Mask A Web browser for configuration such as Microsoft Internet Explorer 6.0 or above, or Netscape Navigator 4.78 or above or Firefox Package Content If any missing or damaged,
Streszczenie treści zawartej na stronie nr. 12
Connect the other end of the Ethernet cable to the ZMAX-8210. Tighten the water-proof connector. A ground wire connects the ZMAX-8210. Ground Note： To keep the ZMAX-8210 antenna intact, a plastic coat is over the antenna. Remove the coat wile using it. Warning： Chapter 2 Introduction - 6 -
Streszczenie treści zawartej na stronie nr. 13
Be sure to your ZMAX-8210 is connected the ground wire, preventing something unexpected. Antenna Installation 16dBi built-in antenna is placed in the ZMAX-8210, so you need not install antenna. The ZMAX-8210-E needs an external antenna. You should choose your antenna as your need. Warning： Keep your ZMAX-8210 associated with the antenna away from power line, lamp, electrified wire fence or anything others electrified. Though a thunder-proof component is built in, it is recommende
Streszczenie treści zawartej na stronie nr. 14
Chapter 3 Basic Settings Default Factory Settings We’ll elaborate the ZMAX-8210 default factory settings. You can re-acquire these parameters by resort button. If necessary, please refer to the “the way to restore default factory settings. Table 1 ZMAX-8210 Default Factory Settings Feature Factory Default Settings User Name admin Password password Device Name Devicexxxxxx（xxxxxx represents the last 6 digits of MAC address） Spanning Tree Protocol Enable IP Type：STATIC IP Address：19
Streszczenie treści zawartej na stronie nr. 15
Figure 5 Safety Alert Clicking “Yes” ushers you into the login. Figure 6 Login Note： Make sure the PC IP address need to be matched the device. For instance, the ZMAX-8210 is 192.168.1.1, and your PC IP should be 192.168.1. X. Enter the default name “admin” in the username field and “password” in the password field。Clicking “ Login now ” will usher you into the ZMAX-8210 management interface. Chapter 3 Basic Settings
Streszczenie treści zawartej na stronie nr. 16
Figure 7 ZMAX-8210 General Information Device Name Clicking“Basic Settings” ，you’ll see the ZMAX-8210Name. You may assign any device name to this CPE. This name is only used by the CPE administrator for identification purposes. Unique, memorable names are helpful, especially if you are employing multiple access points on the same network. This name is composed of 15 characters with 0-9, A-Z, a-z or “-“. Figure 8 ZMAX-8210 CPE Name “WINS” enabled, you have the alternative of enter
Streszczenie treści zawartej na stronie nr. 17
By default, the ZMAX-8210 CPE is Devicexxxxxx(xxxxxx represents the last 6 digits of MAC address). No figure is allowed to represent initial. When WINS undertakes interpreting, make sure the PC IP address need to be matched the CPE. For instance, the ZMAX-8210 is 192.168.1.1, and your PC IP should be 192.168.1. X. Bridge and Router Mode The ZMAX-8210 is capable of working under bridge and router modes. Opening“IP Settings”will navigate you to the configuring mode page. Figure 9
Streszczenie treści zawartej na stronie nr. 18
If you fail to obtain IP address for the ZMAX-8210, the CPE will turn to the client address for use. Wireless Parameters Opening“Radio Settings can lead you to the ZMAX-8210 wireless parameters. You can set what you desire. Figure 10 ZMAX-8210 Wireless Parameters Base Station ID： This field allows you to enter the Base Station ID you want to connect, to establish a tie between this CPE and the Base Station. Duplex Mode：This field allows you to have the options of TDD and HFDD mo
Streszczenie treści zawartej na stronie nr. 19
devices. Encryption：This field provides encryption options. Note： When the communication is established, the encryption shall be completely identical between the ZMAX-8210 and the Base Station, IR Bit：This field identifies whether forward “initial ranging data”。 Note： There shall be in complete accord in the parameters between IR Bit and Base Station. Create a Link between the ZMAX-8210 and WiMAX Base Station Acting as a customer premise equipment (CPE), the ZMAX-8210 aim
Streszczenie treści zawartej na stronie nr. 20
The parameters set in the ZMAX-8210 shall match the ones in the WiMAX Base Station, when the tie is established. Using “ping” to check whether the communication is sound. Take an example as follows. Ping 192.168.1.1 to check the communication between the ZMAX-8210 and PC. 192.168.1.200 check the communication between the ZMAX-8210 and WiMAX Base Station. If you fail to ping, please see Troubleshooting. Chapter 3 Basic Settings
