Streszczenie treści zawartej na stronie nr. 1
Contents
Introduction 2
Installation 3
®
Using PeripheralVision
to Configure the IP Router 5
IP Router Page 5
Passwords 6
Routing Table Page 7
Broadcast Forward Page 8
®
PeripheralVision Licensing 9
Safety and Location Advice 10
Troubleshooting and
Technical Reference 11
Technical Support 12
1
Streszczenie treści zawartej na stronie nr. 2
Introduction The Ringdale IP Router is a local two port Ethernet IP router which enables IP packets to be routed from one Network/Subnet to another on your Local or Wide Area Network, and even across the Internet if required. The IP Router is simple to install and can be configured and remotely managed using the ® PeripheralVision software provided. ® Use PeripheralVision to create a routing table which directs the IP packets straight to the required IP Address, giving greater control over the
Streszczenie treści zawartej na stronie nr. 3
Installation Connect the power cord to the Power Input socket as shown in the illustration below and plug into power supply. The LEDs will flash to indicate that the device has powered up. The illustration shows the position of the ports and the diagnostic LEDs. The two ports are itemized as follows: Network 1 Port Connect to this port the RJ45 cable from the hub of the first network/Subnet Mask you wish to route to. Network 2 Port Connect to this port the RJ45 cable from the hub of the second
Streszczenie treści zawartej na stronie nr. 4
The LEDs are itemized as follows: Link (Yellow) LED The Link LED indicates that the port is functionally connected to an external port. It lights up when the connected hub is turned on. If the LED does not light up, there may be a problem with the cabling or the hub. Write (Red) LED The write LED blinks when a data packet is being sent from that particular port. Read (Green) LED The Read LED blinks when a data packet is received, regardless of the status of the port, even if the port is disabled
Streszczenie treści zawartej na stronie nr. 5
® Using PeripheralVision to Configure the IP Router Full Installation and operational procedures for ® PeripheralVision are dealt with in the separate manual accompanying the Installation CD, refer to this if any problems are encountered in the procedure detailed below. ® Install PeripheralVision onto a PC on Network TM One. Using the Locate NPMP discovery tool in ® PeripheralVision , enter the default set IP address (11.22.33.44). The IP router will appear on the network map, it will be an
Streszczenie treści zawartej na stronie nr. 6
Default Gateway IP Address Enter here the default gateway IP address for Network 1. DNS Name Server Address This information is not necessary. Local IP Address Enter here the router’s IP address for Network 2. Local IP Subnet Mask Enter here the subnet mask for Network 2. Click on Apply to register the new information. Passwords It is strongly recommended that Passwords are set for access to all router pages in ® PeripheralVision because of the sensitive nature of the information that can be con
Streszczenie treści zawartej na stronie nr. 7
Routing Table Page Other property pages display further information. Select the Routing Table page, which is shown below. It is now necessary to tell the IP Router where to route the IP packets to. This is done by creating a Routing Table as above. Configure each route as follows. IP Address Enter here the IP Address of the subnet you want to route to. Subnet Mask Enter here the Subnet Mask of the above IP Address. Gateway Enter here the Gateway address of the above. H (Hops) Enter here the n
Streszczenie treści zawartej na stronie nr. 8
Click on the Add Route button to add a new route. Click on the Edit Route button to change the configuration of an existing route. Click on the Delete Route button to remove a route. Once the routes have been set up as required, click on Apply. The Ringdale IP Router is now configured and will route your IP packets automatically as specified. Broadcast Forward Page The IP router also has the facility to forward broadcasts. Select the B’cast Forward page, which is shown below: 8
Streszczenie treści zawartej na stronie nr. 9
To forward a broadcast through the router to the required IP address click on Add. This will open the window below: Enter the IP address and click on OK. The IP address will be entered into the list. To make changes to an IP address already on the list, click on the required address to select it and then click on Edit. This will open the above window with the IP address you wish to edit. Make the changes and click on OK. To delete an IP address from the list, click on the required address to
Streszczenie treści zawartej na stronie nr. 10
Safety and Location Advice The device is designed to operate in a typical office environment. Choose a site that is: Well ventilated and away from sources of heat including direct sunlight. Away from sources of vibration or physical shock. Isolated from strong electromagnetic fields produced by electrical devices. Provided with a properly grounded wall outlet. Do not attempt to modify or use the supplied AC power cord if it is not the exact type required. Ensure that the system is disconnected
Streszczenie treści zawartej na stronie nr. 11
Troubleshooting and Technical Reference Symptom Poss. Cause Action LEDs do not flash Power switched off Switch on at power-up Power cord not connected Plug in Router Fuse defect Replace fuse Link LED does No cable inserted Connect to hub not light up and Router Router not Check power supply powered up for Router Wrong cable type Verify cable selection Bad cable Replace cable Technical Specification Mains supply: Input: 90..240 volts AC Frequency: 50..60Hz Power: 3 watts typical Network One Co
Streszczenie treści zawartej na stronie nr. 12
Technical Support Ringdale Ltd, Ringdale Inc. and Ringdale GmbH all have Technical Support Departments. Their addresses and contact details are found on the back cover of this manual. Before you call: Please have the following information ready before calling: Type of adapters installed in the System. The adapter settings and interrupt options. Network Information: Network operating system type and version, server configuration. LAN topology: Type of cable being used, size of network, number of
