Streszczenie treści zawartej na stronie nr. 1
DS3- Quad 10/100 RIOP Installation Guide
Compatible Systems Corporation
4730 Walnut Street
Suite 102
Boulder, Colorado 80301
303-444-9532
800-356-0283
http://www.compatible.com
Streszczenie treści zawartej na stronie nr. 2
DS3-Quad 10/100 RIOP Installation Guide, Version 1.0 Copyright© 1999, Compatible Systems Corporation All rights reserved. VSR, VSR-2, MicroRouter and CompatiView are trademarks of Compatible Systems Corporation. Other trademarks are the property of their respective holders. FCC Notice: This product has been certified to comply with the limits for a Class A computing device, pursuant to Subpart J of Part 15 of FCC Rules. It is designed to provide reasonable protection against radio or tel
Streszczenie treści zawartej na stronie nr. 3
Table of Contents Introduction to the DS3-Quad 10/100 RIOP 1 Chapter 1 - Network Installation 2 Connecting the DS3-Quad 10/100 to the Ethernet 2 DS3 Line Connection Requirements 2 Connecting the DS3-Quad 10/100 to a DS3 Line 3 Connecting a Management Console 3 Powering Up the Router 3 Chapter 2 - Quickstart Instructions 4 ETHERNET INTERFACE CONFIGURATION 4 IP Protocol 4 Required for IP 4 Suggested for IP 5 IPX Protocol 5 Required for IPX 5 Suggested for IPX 5 AppleTalk Protocol 5 Required for Ap
Streszczenie treści zawartej na stronie nr. 4
Table of Contents IP Protocol 8 Required for IP Numbered Interface 8 Required for IP Unnumbered Interface 8 Suggested for IP 8 IPX Protocol 9 Required for IPX 9 Suggested for IPX 9 AppleTalk Protocol 9 Required for AppleTalk 9 Suggested for AppleTalk 9 DECnet Protocol 9 Required for DECnet 9 SMDS Configuration 10 Link Configuration 10 Suggested for Dedicated/Leased Line Operation 10 SMDS Addressing 10 SAVING A CONFIGURATION FILE TO FLASH ROM 10 Chapter 3 - Shipping Defaults 11 Ethernet Interface
Streszczenie treści zawartej na stronie nr. 5
Introduction to the DS3-Quad 10/100 RIOP 1 Introduction to the DS3-Quad 10/100 RIOP The DS3-Quad 10/100 Routing Input/Output Processor (RIOP), as part of the VSR multigi- gabit switching router, allows you to connect a remote corporate network and up to four local Ethernet segments. The DS3 interface has a data capacity of 44.736 Mbps, while the Ethernet interfaces can operate at either 10 Mbps or 100 Mbps. This section of the manual contains information specific to the DS3-Quad 10/100 RIOP
Streszczenie treści zawartej na stronie nr. 6
Chapter 1 - Network Installation 2 Chapter 1 - Network Installation DS3-Quad 10/100 RIOP Front Panel This section of the manual will help you install the DS3-Quad 10/100 RIOP to connect a local Ethernet and remote corporate network. These connections can be made to other Compatible Systems routers or routers from other vendors. In summary, the steps for installation are: 1. After mounting the router or placing on a desktop, make sure it is not connected to any power source. 2. Connect the r
Streszczenie treści zawartej na stronie nr. 7
Chapter 1 - Network Installation 3 Note: The DS3-Quad 10/100 RIOP includes loopback features which can be used to check the functionality of your DS3 line. Before attempting to route network traffic, use these features to check the line’s basic integrity. Connecting the DS3-Quad 10/100 to a DS3 Line The DS3 line port consists of two 75 ohm BNC female coaxial connectors labeled DS3 XMT and DS3 RCV. To connect the router to the DS3 line, you need two AT&T type 734A or equiv- alent coaxial c
Streszczenie treści zawartej na stronie nr. 8
Chapter 2 - Quickstart Instructions 4 Chapter 2 - Quickstart Instructions This Quickstart chapter briefly discusses the major parameters that must be set in order to use the DS3-Quad 10/100 RIOP as part of your VSR multigigabit switching router. Detailed information on the meaning of the router’s parameters is provided in the Compa- tiView Management Software Reference Guide and the Text-Based Configuration and Command Line Management Reference Guide. You should use this chapter as a starti
Streszczenie treści zawartej na stronie nr. 9
Chapter 2 - Quickstart Instructions 5 Suggested for IP These parameters help supply information about the segment that the interface is connected to. With this information, routing can take place. Set IP RIP 1, IP RIP 2 or OSPF (Open Shortest Path First) Set IP static routes CV: Use the TCP/IP Routing: Ethernet Dialog Box to set RIP, and the IP Static Routing Dialog Box (under Global/IP Static Routes) to set static routes. OSPF can only be configured using text-based configuration. TB:
Streszczenie treści zawartej na stronie nr. 10
Chapter 2 - Quickstart Instructions 6 numbers you wish to configure) section. Use configure and set the Enabled, Area, and Node keywords in the DECnet Global section. Note: Setting DECnet on for any port with the command line also sets DECnet on globally. In CompatiView you must set a global parameter and a port-specific parameter. Suggested for DECnet Setting the parameters above should be adequate for most installations. WAN Interface Configuration In order to use the WAN interface, you m
Streszczenie treści zawartej na stronie nr. 11
Chapter 2 - Quickstart Instructions 7 Protocol) Set IP static routes CV: Use the TCP/IP Routing: WAN Dialog Box to set RIP, and the IP Static Routing Dialog Box (under Global/IP Static Routes) to set static routes. OSPF and BGP can only be config- ured using text-based configuration. TB: Use configure and set either the RIPVersion keyword or the OSPFEnabled keyword in the IP WAN 0 section. Add static routes and a default router using the edit config IP Static command. Note: Due to the
Streszczenie treści zawartej na stronie nr. 12
Chapter 2 - Quickstart Instructions 8 Set Frame Relay connection CV: Use the Link Configuration: WAN Dialog Box. TB: Use configure and then set the Mode and ConnectMode keywords in the Link Config WAN 0 section. Suggested for Dedicated Line Operation Dedicated line operation generally does not require additional parameters for operation. Frame Relay DLCI Mappings If you are connecting to another Compatible Systems router, this information is not required for Frame Relay operation. Compati
Streszczenie treści zawartej na stronie nr. 13
Chapter 2 - Quickstart Instructions 9 Box (under Global/IP Static Routes) to set static routes. OSPF and BGP can only be config- ured using text-based configuration. TB: Use configure and set either the RIPVersion keyword or the OSPFEnabled keyword in the IP WAN 0 section. Add static routes and a default router using the edit config IP Static command. Note: Due to the complexity of BGP, configuration parameters for BGP are not given in this Quickstart. For help with BGP configuration pa
Streszczenie treści zawartej na stronie nr. 14
Chapter 2 - Quickstart Instructions 10 TB: Use configure and set the Mode keyword in the DECnet WAN 0 section. Note: Setting DECnet on for any port with the command line also sets DECnet on globally. In CompatiView you must set a global parameter and a port-specific parameter. SMDS Configuration This section covers the settings required for SMDS (Switched Multi-megabit Data Service) operation of the DS3 WAN interface (IP only). SMDS is a connectionless, packet-switched service that offer
Streszczenie treści zawartej na stronie nr. 15
Chapter 3 - Shipping Defaults 11 Chapter 3 - Shipping Defaults Ethernet Interfaces IP Routing Defaults Off, all interfaces IP Bridging Defaults On, all interfaces Address: 198.41.12.1 Subnet Mask: 255.255.255.0 Broadcast Address: 198.41.12.255 IP RIP off IPX Routing Defaults 802.3 on, autoseeding, all interfaces 802.2 on, autoseeding, all interfaces Type II on, nonseeding 802.2 SNAP on, nonseeding IPX Bridging Defaults Off, all interfaces AppleTalk Routing Defaults Phase
Streszczenie treści zawartej na stronie nr. 16
Chapter 4 - LED Patterns 12 Chapter 4 - LED Patterns Some of the LEDs on the front of the VSR multigigabit switching router serve dual functions. In addition to indicating certain router-wide operating conditions, they can also display port-specific information. Note: Any continuous flashing pattern not noted in this chapter may be caused by a hard- ware failure. Please call Compatible Systems Technical Support if your router shows a hard- ware failure. Router LED Patterns The followin
Streszczenie treści zawartej na stronie nr. 17
Chapter 4 - LED Patterns 13 DS3-Quad 10/100 RIOP LED Patterns The following LEDs and light patterns provide information about the DS3-Quad 10/100 RIOP interfaces. Ethernet Traffic Indicators Scan from 1 to 3: Ethernet transmit packet Scan from 5 to 3: Ethernet receive packet DS3 Indicators Scan from 1 to 3: WAN transmit packet Scan from 5 to 3: WAN receive packet Ethernet Connection Indicators Link: The Link light indicates that there is a good connection to the hub. Activity: The Activi
