Streszczenie treści zawartej na stronie nr. 1
54Mbps/11Mbps Wireless ADSL Modem Router
WMR-G54
User’s Guide
Streszczenie treści zawartej na stronie nr. 2
2
Streszczenie treści zawartej na stronie nr. 3
Table of Contents Introduction Introduction 3 A Look at the Hardware 3 WMR-G54 Wireless ADSL Router allows you to share the single Front Panel 4 internet account. With built-in NAT, this Router allows up to 253 Back Panel 4 users on the Ethernet LAN simultaneously and up to 16 users Hardware Installation 5 on the 802.11g/b Wireless LAN simultaneously. WMR-G54 has Configure the Router for the first time 5 the throughput speeds of up to 54Mbps and ad
Streszczenie treści zawartej na stronie nr. 4
following table defines the behavior for each LED: transferred over the ADSL connection. PPP Link PPP Blinking – PPP is connected. Connection 11G Wireless - Steady on – Wireless LAN access point is LAN enabled. - Blinking – Data is being transferred over the Wireless LAN connection. LED Represents Activity / Status Power Power The Power LED will light up when the Back Panel device is powered on. USB USB - Steady on – USB is connected to a host Connection PC. - Blinking – Da
Streszczenie treści zawartej na stronie nr. 5
cable to the USB port and connect the other end Step 2. Connect the LAN port of the router to the Ethernet port to the computer. of your computer with the Ethernet cable provided. Reset Use an object, such as a stretched paper clip, to Step 3. Connect the 16V AC power adapter to the power socket press the button for at least 3 seconds. LAN 1, 2, of router, and plug the adapter into a mains power socket. 3, 4 LED will light up for a short time and then be Switch on the router. If the pow
Streszczenie treści zawartej na stronie nr. 6
then click Properties button. For Windows 2000/Windows XP 1. Right-click on My Network Places icon on the desktop and then click Properties in menu. 4. Check the radio button for Specify an IP address. In the IP address box, type the assigned IP address 192.168.1.x (x is any number between 2 and 254). 5. In the Subnet mask box, type the subnet mask 255.255.255.0. 6. In the default gateway box, type the default gateway IP address. For example, 192.168.1.1. 2. Double-click Local
Streszczenie treści zawartej na stronie nr. 7
Internet Service Provider (ISP). 3. After login, WMR-G54 Web UI screen will appear. The ADSL Modem Router can be configured with your web browser. The product provides a very easy and user-friendly interface for configuration. 1. Open your web browser. Enter http://192.168.1.1 in the web browser’s address field, and press the enter key. 2. A login window will appear. Enter admin in the User Name field and enter admin in the Password field. I. Device Info The Device In
Streszczenie treści zawartej na stronie nr. 8
II. Quick Setup 3. The ATM PVC Configuration page will appear. Enter the The Quick Setup will guide you through the steps necessary to appropriate VPI and VCI values. Select appropriate configure your DSL Router. Service Category. Click Next. PVC is identified by the VPI (Virtual Path Identifier) and VCI III. Configure WAN (DSL) Connectivity (Virtual Channel Identifier). Consult your ISP to get the numbers. The valid range for the VPI number is from 0 to 255 (The default 1
Streszczenie treści zawartej na stronie nr. 9
UBR With PCR, CBR, Non Realtime VBR, and Realtime VBR. WMR-G54 ADSL Modem Router supports the following five network operating modes over an ATM PVC WAN interface: PPP over ATM (PPPoA) PPP over Ethernet (PPPoE) MAC Encapsulated Routing (MER) IP over ATM (IPoA) Bridging The steps to configure PPP over ATM (PPPoA) are similar to PPPoE. PPP over Ethernet (PPPoE) 4. A Connection Type page will appear. There are several 1. Select the PPP over Ethernet (PPPoE) radio b
Streszczenie treści zawartej na stronie nr. 10
2. In the PPP Username and Password page, enter the user 3. Check the box Disconnect if no activity if you want to name and password supplied by your ISP in PPP enable the function of automatic disconnection. It will Username and PPP Password fields. auto-disconnect the ADSL Modem Router when there is no activity on the line for a period of time. PPP IP Extension is a special feature deployed by some service providers. Unless your ISP specifically requires this setup, do NOT sel
Streszczenie treści zawartej na stronie nr. 11
Allows only one PC on the LAN Service if you want to enable WAN Service. Click Next. The public IP address assigned by the remote using the PPP/IPCP protocol is actually not used on the WAN PPP interface. Instead, it is forwarded to the PC’s LAN interface through DHCP. Only one PC on the LAN can be connected to the remote since the DHCP server within the ADSL router has only a single IP address to assign to a LAN device. NAT and firewall are disabled when this option is selecte
Streszczenie treści zawartej na stronie nr. 12
7. The WAN Setup page will appear. Click the Save/Reboot 8. Close your Web UI window and wait for about 2 minutes button. The router will reboot automatically with the new before reopening your web browser. settings in effect. 12
Streszczenie treści zawartej na stronie nr. 13
IP over ATM (IPoA) 2. DHCP is not supported over IpoA. Enter your WAN IP address, WAN Subnet Mask, gateway IP address and DNS 1. Select the IP over ATM (IPoA) radio button and scroll down server IP address provided by your ISP to configure the to select the appropriate Encapsulation Mode. There are WAN IP settings. Then click the Next button. two encapsulation types available: LLC/Snap-Routing and VC/MUX. Then click Next button. 13
Streszczenie treści zawartej na stronie nr. 14
provided by the ISP. The user may have many private addresses masked by the single address provided by the ISP. 4. If you want to enable the Firewall function, check the box Enable Firewall. If the Firewall is enabled, it will display a Firewall submenu on the left panel after reboot. Firewall will rejects any unsolicited data from the Internet to access the computer on your LAN. Basically, if you do not request data, the data will not be allowed by the firewall to pass. 5. If
Streszczenie treści zawartej na stronie nr. 15
8. The WAN Setup – Summary page displays a summary of Bridging all WAN setting profiles. Click the Save button to save all the settings. 1. Select the Bridging radio button and scroll down to select the appropriate Encapsulation Mode. There are two 9. The WAN Setup page will appear. Click the Save/Reboot encapsulation types available: LLC/Snap-Bridging and button. The router will reboot automatically with the new VC/MUX. Then click the Next button. settings in effect. 15
Streszczenie treści zawartej na stronie nr. 16
The LAN IP in bridge operating mode is needed for local users to manage the ADSL Modem Router. And no IP address is needed 2. Check the box Enable Bridge Service. Enter a desired for the WAN in bridge mode. name in the Service Name field. It is used to identify the service. Then click the Next button. 3. The WAN Setup – Summary page displays a summary of all WAN setting profiles. Click the Save button to save all the settings. 16
Streszczenie treści zawartej na stronie nr. 17
4. The WAN Setup page will appear. Click the Save/Reboot 5. Close your Web UI window and wait for about 2 minutes button. The router will reboot automatically with the new before reopening your web browser. settings in effect. 17
Streszczenie treści zawartej na stronie nr. 18
IV. Configure Wireless Connectivity 3. Enter a desired name in SSID field. This SSID is a network name that identifies the wireless devices in the network. 1. Click the Wireless tab on the left frame. A Wireless - Basic The default value is WMR-G54. All workstations and page will appear on the right frame. Check the box Enable access points must use the same SSID to be able to Wireless. communicate with one another. The SSID is a 32-character field, and the value is case sensitive. 4. C
Streszczenie treści zawartej na stronie nr. 19
Europe – EU Declaration of Conformity This device complies with the essential requirements of the This device is a 2.4 GHz wireless LAN transceiver, intended for R&TTE Directive 1999/5/EC. The following test methods have home and office use in all EU and EFTA member states, except been applied in order to prove presumption of compliance with in France, Belgium and Italy where restrictive use applies. the R&TTE Directive 1999/5/EC: In Italy the end-user should apply for a license at
Streszczenie treści zawartej na stronie nr. 20
Buffalo Technology Europe Wireless products helpdesk * Buffalo Technology UK +44 8712 501260 (UK & Ireland) * 176, Buckingham Avenue +44 1753 555050 (Rest of Europe) Slough, Berkshire, SL1 4RD United Kingdom helpdesk@buffalo-technology.ie Tel. +44 (0) 1753 555000 Fax. +44 (0) 1753 535420 Buffalo Technology Ireland Free Zone East Shannon Co. Clare Ireland Tel. +353 61 708090 Fax. +353 61 360140 * 8.5p/13c per minute + local charge www.buffalo-tec
