Instrukcja obsługi Nexus 21 Depth TH 52

Instrukcja obsługi dla urządzenia Nexus 21 Depth TH 52

Urządzenie: Nexus 21 Depth TH 52
Kategoria: Wyposazenie lodzi
Producent: Nexus 21
Rozmiar: 0.26 MB
Data dodania: 7/3/2013
Liczba stron: 18
Drukuj instrukcję

Pobierz

Jak korzystać?

Naszym celem jest zapewnienie Ci jak najszybszego dostępu do treści zawartych w instrukcji obsługi urządzenia Nexus 21 Depth TH 52. Korzystając z podglądu online możesz szybko przejrzeć spis treści i przejść do strony, na której znajdziesz rozwiązanie swojego problemu z Nexus 21 Depth TH 52.

Dla Twojej wygody

Jeżeli przeglądanie instrukcji Nexus 21 Depth TH 52 bezpośrednio na tej stornie nie jest dla Ciebie wygodne, możesz skorzystać z dwóch możliwych rozwiązań:

  • Przeglądanie pełnoekranowe - Aby wygodnie przeglądać instrukcję (bez pobierania jej na komputer) możesz wykorzystać tryp przeglądania pełnoekranowego. Aby uruchomić przeglądanie instrukcji Nexus 21 Depth TH 52 na pełnym ekranie, użyj przycisku Pełny ekran.
  • Pobranie na komputer - Możesz również pobrać instrukcję Nexus 21 Depth TH 52 na swój komputer i zachować ją w swoich zbiorach. Jeżeli nie chcesz jednak marnować miejsca na swoim urządzeniu, zawsze możesz pobrać ją w przyszłości z ManualsBase.
Nexus 21 Depth TH 52 Instrukcja obsługi - Online PDF
Advertisement
« Page 1 of 18 »
Advertisement
Wersja drukowana

Wiele osób woli czytać dokumenty nie na ekranie, lecz w wersji drukowanej. Opcja wydruku instrukcji również została przewidziana i możesz z niej skorzystać klikając w link znajdujący się powyżej - Drukuj instrukcję. Nie musisz drukować całej instrukcji Nexus 21 Depth TH 52 a jedynie wybrane strony. Szanuj papier.

Streszczenia

Poniżej znajdziesz zajawki treści znajdujących się na kolejnych stronach instrukcji do Nexus 21 Depth TH 52. Jeżeli chcesz szybko przejrzeć zawartość stron znajdujących się na kolejnych strinach instrukcji, możesz z nich skorzystać.

Streszczenia treści
Streszczenie treści zawartej na stronie nr. 1


Depth TH 52
- Transducer -
Installation and Operation Manual
Installation and Operation Manual
English

English

Streszczenie treści zawartej na stronie nr. 2

DEPTH TH52 1

Streszczenie treści zawartej na stronie nr. 3

DEPTH TH52 2

Streszczenie treści zawartej na stronie nr. 4

DEPTH TH52 CONTENTS: 1 Applications................................................................................4 2 Tools and Materials Needed......................................................4 3 Mounting Location .....................................................................5 3.1 Acoustic Noise...............................................................................................5 3.2 Placement........................................................................

Streszczenie treści zawartej na stronie nr. 5

DEPTH TH52 INSTALLATION INSTRUCTIONS Thru-Hull Depth Transducer Low Profile, Flush, and Retractable Models IMPORTANT: Please read these instructions completely before proceeding with the installation. These directions supersede any other instructions in your instrument manual if they differ. WARNING: NEVER USE SOLVENTS! Certain cleaners, fuel, paints, sealants, and other products may contain strong solvents, such as acetone, which attack many plastics greatly reducing the

Streszczenie treści zawartej na stronie nr. 6

DEPTH TH52 3 Mounting Location 3.1 Acoustic Noise Acoustic noise is always present and these sound waves can interfere with the operation of the transducer. Background noise from sources such as: waves, fish, and other vessels cannot be controlled. However, carefully selecting the transducer mounting location can minimize the affect of vessel generated noise from the propeller(s) and shaft(s), other machinery, and other echosounders. The lower the noise level, the higher the echosounde

Streszczenie treści zawartej na stronie nr. 7

DEPTH TH52 3.3 Boat Types (see Figure 1) • Displacement hull powerboat—Locate 1/3 aft LWL and 150–300mm (6–12") off the centerline on the side of the hull where the propeller is moving downward. • Planing hull powerboat—Mount well aft, on or near the centerline, and well inboard of the first set of lifting strakes to insure that the transducer is in contact with the water at high speeds. Mount on the side of the hull where the propeller is moving downward. Outboard and I/O—Mount

Streszczenie treści zawartej na stronie nr. 8

DEPTH TH52 4 Installation Cored fiberglass hull—Follow separate instructions on page 4. 4.1 Hole Drilling Warning: Always wear safety goggles and a dust mask. 1. Drill a 3 mm or 1/8" pilot hole from inside the hull. If there is a rib, strut, or other hull irregularity near the selected mounting location, drill from the outside. Note: If the pilot hole is drilled in the wrong location, drill a second hole in a better location. Apply masking tape to the outside of the hull over

Streszczenie treści zawartej na stronie nr. 9

DEPTH TH52 4.2 Bedding Caution: Never pull, carry, or hold the transducer by its cable; this may sever internal connections. 1. Remove the hull nut and any washer (see Figure 2). Also remove the cap nut and the transducer insert. 2. Apply a 2mm (1/16") thick layer of sealant around the lip of the housing that contacts the hull and up the sidewall of the housing, 6 mm (1/4") higher than the combined thickness of the hull, washer(s), and the hull nut. This will ensure there is se

Streszczenie treści zawartej na stronie nr. 10

DEPTH TH52 tighten only. Do not over tighten. Warning: Always attach the safety wire to prevent the insert from backing out in the unlikely event that the cap nut fails or is screwed on incorrectly. 6. Attach the safety wire. Attach the safety wire to one eye in the hull nut. Lead the wire in a counterclockwise direction and thread it through one eye in the cap nut, the pull ring, the second eye in the cap nut, and the second eye in the hull nut. Twist the wire securely to itself.

Streszczenie treści zawartej na stronie nr. 11

DEPTH TH52 5.3 Installation in a Cored Fiberglass Hull The core (wood or foam) must be cut and sealed carefully. The core must be protected from water seepage, and the hull must be reinforced to prevent it from crushing under the hull nut allowing the housing to become loose. Warning: Always wear safety goggles and a dust mask. 1. Drill a 3 mm or 1/8" pilot hole from inside the hull (see Figure 3). If there is a rib, strut, or other hull irregularity near the selected mounting l

Streszczenie treści zawartej na stronie nr. 12

DEPTH TH52 6 CONNECTION TO INSTRUMENT/CONTACTS The depth transducer connects to the FI-30 Server or directly. The transducer cable is clearly marked with No 2 and the colours will correspond to input screw terminal on the Server. IMPORTANT! DO NOT CUT OR EXTEND THE 8 M TRANSDUCER CABLE! 7 Calibration Calibration is carried out in the Multi Control instrument (see manual). 8 Maintenance 8.1 Antifouling Paint Surfaces exposed to salt water must be coated with anti-fou

Streszczenie treści zawartej na stronie nr. 13

DEPTH TH52 9 TECHNICAL DATA Dimensions Transducer: 51 x 86 mm (1 5/8” x 3 3/8”) Transducer cable: 8 m (9.9 ft + 26.2 ft) Power supply: 12V DC (10-16V) Power consumption: 0.2 W Depth range: 0.8 - 150 m (3 - 450 ft) at speed up to 30 knots. Accuracy: ± 0.1 % Type of transducer: Piezocrystal 200 kHz Temperature range: Operation -10°C to + 70°C Storage -35°C to +85°C The depth measuring is based on the echos speed in water which is 1.463 m/sec. 12

Streszczenie treści zawartej na stronie nr. 14

DEPTH TH52 13

Streszczenie treści zawartej na stronie nr. 15

DEPTH TH52 14

Streszczenie treści zawartej na stronie nr. 16

DEPTH TH52 15

Streszczenie treści zawartej na stronie nr. 17

DEPTH TH52 16

Streszczenie treści zawartej na stronie nr. 18

DEPTH TH52 Copyright ©: Nexus Marine AB Kuskvägen 4, 191 62 Sollentuna, Sweden Tel: +46 -(0) 8 – 506 939 00. Fax: +46 -(0) 8 -506 939 01 www.nexusmarine.se 17 22418-1 Edition 1


Podobne instrukcje
# Instrukcja obsługi Kategoria Pobierz
1 Nexus 21 Compass Data Instrukcja obsługi Wyposazenie lodzi 2
2 Sony HFBK-TS1 Instrukcja obsługi Wyposazenie lodzi 2
3 Samsung iDCS100 Instrukcja obsługi Wyposazenie lodzi 3
4 Belkin 8000I Instrukcja obsługi Wyposazenie lodzi 15
5 Attwood 4030 Instrukcja obsługi Wyposazenie lodzi 3
6 Attwood 4624 Instrukcja obsługi Wyposazenie lodzi 0
7 Attwood 4620 Instrukcja obsługi Wyposazenie lodzi 0
8 Attwood 4061 Instrukcja obsługi Wyposazenie lodzi 0
9 Attwood 1675 Instrukcja obsługi Wyposazenie lodzi 0
10 Attwood 4623 Instrukcja obsługi Wyposazenie lodzi 0
11 Attwood 4801 Instrukcja obsługi Wyposazenie lodzi 3
12 Attwood 4060 Instrukcja obsługi Wyposazenie lodzi 1
13 Attwood 4202 Instrukcja obsługi Wyposazenie lodzi 2
14 Attwood 66510 Instrukcja obsługi Wyposazenie lodzi 0
15 Attwood 66513 Instrukcja obsługi Wyposazenie lodzi 0