Instrukcja obsługi Patton electronic 1110ARC

Streszczenie treści zawartej na stronie nr. 1

Dear Valued Customer,
Thank you for purchasing Patton Electronics products! We do
appreciate your business. I trust that you find this user manual helpful.
We manufacture one of the widest selections of data
communications products in the world including CSU/DSU's, network USER
termination units, powered and self-powered short range modems, fiber optic
modems, interface converters, baluns, electronic data switches, data-line surge
MANUAL
protectors, multiplexers, transceivers, hubs, print s

Streszczenie treści zawartej na stronie nr. 2

1.0 WARRANTY INFORMATION 1.3 SERVICE Patton Electronics warrants all Model 1110ARC components to be free from defects, and will—at our option—repair or replace the All warranty and nonwarranty repairs must be returned freight prepaid and insured to Patton Electronics. All returns must have a product should it fail within one year from the first date of shipment. This warranty is limited to defects in workmanship or materials, and Return Materials Authorization number on the outside of the shi

Streszczenie treści zawartej na stronie nr. 3

2.0 GENERAL INFORMATION 3.0 CONFIGURATION Thank you for your purchase of this Patton Electronics product. This setting describes the location and orientation of the Model This product has been thoroughly inspected and tested and is 1110ARC’s configuration jumpers. There are two sets of jumpers to warranted for One Year parts and labor. If any questions during set: those on the front “brains” card and those on the rear “interface” installation or use of the 1110ARC, contact Patton Electronics

Streszczenie treści zawartej na stronie nr. 4

3.2 REAR CARD SETTINGS DTE Shield (Pin 1) & FRGND (JB1) The Model 1110ARC is compatible with two dual-fiber interface In the connected (closed) position, this strap links DB-25 pin 1 and cards, one with dual ST connectors and one with dual SMA connectors. frame ground. In the open (disconnected) position, pin 1 is “lifted” from Both cards use an HD-26 female for the RS-232 interface. The frame ground. jumpers on both interface cards function identically. Figure 2 (below) shows the location

Streszczenie treści zawartej na stronie nr. 5

4.0 INSTALLATION Switching the Power Supply On and Off This section describes the functions of the Model 1000R16 rack chassis, tells how to install front and rear Model 1110ARC cards into the The power supply on/off switch is located on the front panel. When plugged in and switched on, a red front panel LED will glow. chassis, and provides instructions for connecting the interface cables. Since the Model 1000R16 is a “hot swappable” rack, it is not necessary 4.1 THE MODEL 1000R16 RACK CHASSIS

Streszczenie treści zawartej na stronie nr. 6

5.0 OPERATION 4.3.1 RS-232 CONNECTION Once you have configured each Model 1110ARC and connected the cables, you are ready to operate the units. This section describes the The RS-232 port on the rear card of the Model 1110ARC is wired as a DCE, and uses a female HD-26 connector. The HD-26 is an LED status monitors and power-up procedure. alternate connector according to the EIA RS-232E specification, and the pin-out is the same as a standard DB-25. Pin 26 is not used. 5.1 LED STATUS MONI

Streszczenie treści zawartej na stronie nr. 7

APPENDIX A APPENDIX B PATTON MODEL 111OARC SPECIFICATIONS PATTON MODEL 1110ARC FACTORY REPLACEMENT PARTS Transmission Line: Dual optical cable The Patton Model 1110ARC rack system features interchangeable rear half cards, power cords/fuses for international various operating Transmission Mode: Asynchronous, half or full duplex, point-to- environments and other user-replaceable parts. Model numbers and point descriptions for these parts are listed below: Interfaces: EIA RS-232, CCITT V.24 Patto

Streszczenie treści zawartej na stronie nr. 8

APPENDIX C APPENDIX C PATTON MODEL 1110ARC BLOCK DIAGRAM PATTON MODEL 1110ARC PIN CONFIGURATIONS UNIVERSAL D-26 INTERFACE (DCE WIRING) 8- (CD) Carrier Detect Data Terminal Ready - (20) 7- (SG) Signal Ground 6- (DSR) Data Set Ready 5- (CTS) Clear to Send 4- (RTS) Request to Send 3- (RD) Receive Data 2- (TD) Transmit Data 1- (FG) Frame Ground Copyright © 1998 Patton Electronics Company All Rights Reserved 14 13