Streszczenie treści zawartej na stronie nr. 1
FIELDPOINT OPERATING INSTRUCTIONS AND SPECIFICATIONS
cFP-2200/2210/2220
Intelligent Real-Time Controllers for Compact FieldPoint
4 5
6
3
7
8
13
2 9
14
12
10
15
1
11
Front Bottom Bottom
1 RS-232 Serial Port 9 RJ-45 Ethernet Port 2 (cFP-2220 Only)
2 RJ-45 Ethernet Port 1 10 Reset Button
3 Removable Compact Flash (cFP-2220 Only) 11 Power Connector
4 Status LED 12 Digital Input/Output Terminals (cFP-2220 Only)
5 Power LED 13 RS-485 Serial Port (cFP-2220 Only)
6 User-Configurable LEDs 14
Streszczenie treści zawartej na stronie nr. 2
This document describes how to mount the cFP-2200/2210/2220 controllers, how to connect the controllers to networks, and how to use the features of the controllers. This document also contains specifications for the controllers. In this document, the cFP-2200/2210/2220 controllers are referred to inclusively as the cFP-22xx. What You Need to Install the cFP-22xx ❑ cFP-22xx intelligent real-time controller ❑ cFP-BP-4 or cFP-BP-8 Compact FieldPoint backplane ❑ Compact FieldPoint I/O modules ❑
Streszczenie treści zawartej na stronie nr. 3
has the following symbol stamped beside it: . Connect the backplane PE ground terminal to safety ground using 14 AWG (1.6 mm) wire with a ring lug. Use the 5/16 in. panhead screw shipped with the backplane to secure the ring lug to the backplane PE ground terminal. To ensure maximum cooling efficiency, mount the Compact FieldPoint so that the I/O module vents are at the top and bottom, as shown in the following figure: Figure 2. cFP-22xx Installed on cFP-BP-4 Mounted Upright Caution Your
Streszczenie treści zawartej na stronie nr. 4
Cabling Clearance 4 slots = 246 mm (9.68 in.) 8 slots = 441 mm (17.4 in.) Cooling Outline 51 mm (2 in.) Cooling Outline 51 mm (2 in.) Figure 3. cFP-22xx Installed on cFP-BP-x, Bottom View with Dimensions 4 slots = 246 mm (9.68 in.) 8 slots = 441 mm (17.4 in.) Cabling Clearance Cooling Outline 51 mm (2 in.) All Around Figure 4. cFP-22xx Installed on cFP-BP-4, Front View with Dimensions cFP-2200/2210/2220 4 ni.com Min. 182 mm (7.18 in.) 106 mm (4.18 in.) Min. 165 mm (6.50 in.) 127 mm (5.00 in
Streszczenie treści zawartej na stronie nr. 5
104.78 mm (4.1 in.) 127.00 mm 63.50 mm (2.5 in.) (5.0 in.) 22.23 mm (0.9 in.) 440.94 mm (17.4 in.) Figure 5. cFP-BP-8, Back View with Dimensions 104.74 mm (4.1 in.) 63.46 mm 127.00 mm (2.5 in.) (5.0 in.) 22.19 mm (0.9 in.) 245.87 mm (9.6 in.) Figure 6. cFP-BP-4, Back View with Dimensions Caution Make sure that no I/O modules are in the backplane before mounting it. © National Instruments Corporation 5 cFP-2200/2210/2220 33.15 mm (1.3 in.) 129.54 mm (5.1 in.) 34.04 mm (1.3 in.) 84.84 mm (3.
Streszczenie treści zawartej na stronie nr. 6
Mounting the Backplane on a DIN Rail The DIN rail mounting kit is NI part number 778614-01. You need one kit to mount the cFP-BP-4 on a standard 35 mm DIN rail. Complete the following steps to mount the backplane on a DIN rail. 1. Fasten the DIN rail clip to the cFP-BP-4 using a number 2 Phillips screwdriver and the 8-32 × 5/16 in. countersink screws shipped with the mounting kit. Figure 7. Installing the DIN Rail Clip on the cFP-BP-4 Caution Do not use screws longer than 5/16 in. to fasten
Streszczenie treści zawartej na stronie nr. 7
3. Press down firmly on the backplane to compress the spring until the clip locks in place on the DIN rail. 4. Connect the PE ground terminal on the backplane to safety ground. Caution Disconnect power and make sure that no I/O modules are in the backplane before removing it from the DIN rail. Mounting the Backplane on a Panel The horizontal panel-mount kit has mounting holes on the sides of the backplane and is NI part number 778616-01. The vertical panel-mount kit has mounting holes on the
Streszczenie treści zawartej na stronie nr. 8
102 mm (4 in.) 260 mm (10.25 in.) Figure 10. cFP-BP-4 with Horizontal Panel Mount Kit Installed, Front View with Dimensions 102 mm (4 in.) 457 mm (18 in.) Figure 11. cFP-BP-8 with Horizontal Panel-Mount Kit Installed, Front View with Dimensions Figure 12. Installing the Vertical Panel-Mount Kit on the cFP-BP-4 cFP-2200/2210/2220 8 ni.com NATIONAL INSTRUMENTS
Streszczenie treści zawartej na stronie nr. 9
34.0 mm (1.34 in.) 178 mm (7.0 in.) 7.6 mm (0.30 in.) 17.8 mm (0.70 in.) 246 mm (9.7 in.) Figure 13. cFP-BP-4 with Vertical Panel-Mount Kit Installed, Front View with Dimensions 33.1 mm (1.31 in.) 374 mm (14.7 in.) 7.6 mm (0.30 in.) 17.8 mm 457 mm (18 in.) (0.70 in.) Figure 14. cFP-BP-8 with Vertical Panel-Mount Kit Installed, Front View with Dimensions 2. Bolt or screw the plates to a panel. 3. Connect the PE ground terminal on the cFP-BP-x to safety ground. Caution Disconnect power and ma
Streszczenie treści zawartej na stronie nr. 10
Mounting the Backplane in a Standard 19 in. Rack The rack-mount kit for Compact FieldPoint is NI part number 778615-01. The following figure shows the dimensions of the rack-mount kit. 374.65 mm (14.750 in.) 278.89 mm (10.980 in.) 2× 8× Diameter 177.8 mm 38.1 mm 34.93 mm +0.07 mm (7.000 in.) (1.375 in.) (1.500 in.) 7.92 mm 0 mm 2× +0.003 in. 6.91 mm 0.312 in. () –0.000 in. (0.272 in.) 63.07 mm 25.4 mm (1.000 in.) (2.483 in.) 25.02 mm (0.985 in.) 37.69 mm 66.29 mm (1.484 in.) (2.610 in.)
Streszczenie treści zawartej na stronie nr. 11
Figure 16. Installing the Rack-Mount Bracket on the cFP-BP-4 Figure 17. Installing the Rack-Mount Bracket on the cFP-BP-8 © National Instruments Corporation 11 cFP-2200/2210/2220 NATIONAL INSTRUMENTS NATIONAL INSTRUMENTS
Streszczenie treści zawartej na stronie nr. 12
2. Bolt the rack-mount bracket to a standard 19 in. rack. 3. Connect the PE ground terminal on the cFP-BP-x to safety ground. Caution Disconnect power and make sure that no I/O modules are in the backplane before removing it from the rack. You can install an 8 in. DIN rail in the rack-mount kit to mount a power supply such as the PS-5. The captive #10-32 nuts on the rack-mount kit make it easy to attach a DIN rail. Use two #10-32 screws of 3/8 in. length as shown in Figure 18. If you want to
Streszczenie treści zawartej na stronie nr. 13
Installing the cFP-22xx on the Backplane 1. Make sure that no power is connected to the controller. 2. Make sure that the controller is right side up with the NI logo at the top, and align the captive screws on the controller with the holes on the backplane. 3. Seat the card edge at the back of the controller in the card-edge connector on the backplane. 4. Press the controller firmly to seat it on the backplane. Figure 19. Installing the Controller on the Backplane 5. Using a number 2 Philli
Streszczenie treści zawartej na stronie nr. 14
Installing I/O Modules on the Backplane 1. Align the captive screws on the I/O module with the holes on the backplane. 2. Press firmly to seat the I/O module on the backplane. 3. Using a number 2 Phillips screwdriver with a shank of at least 64 mm (2.5 in.) length, tighten the captive screws to 1.1 N · m (10 lb · in.) of torque. 4. Repeat this procedure to install additional I/O modules on the backplane. Figure 20. Installing an I/O Module on the Backplane cFP-2200/2210/2220 14 ni.com
Streszczenie treści zawartej na stronie nr. 15
Installing Connector Blocks on the Backplane In order to connect I/O modules to input signals or loads, you need to install a cFP-CB-x connector block or other connectibility accessory for each I/O module on the backplane. Use the connector socket to the right of each I/O module socket. Caution Do not insert or remove connector blocks or other connectivity accessories while power is applied to them. 1. Wire signals or loads as described in the I/O module and connector block operating instru
Streszczenie treści zawartej na stronie nr. 16
Figure 21. Installing a Connector Block on the Backplane 4. Using a number 2 Phillips screwdriver with a shank of at least 64 mm (2.5 in.) length, tighten the captive screws to 1.1 N · m (10 lb · in.) of torque. 5. Repeat this procedure to install additional connector blocks on the backplane. cFP-2200/2210/2220 16 ni.com
Streszczenie treści zawartej na stronie nr. 17
Connecting the cFP-22xx to a Network Connect the cFP-22xx to an Ethernet network using RJ-45 Ethernet port 1 on the controller front panel. Use a standard Category 5 (CAT-5) or better Ethernet cable to connect the controller to an Ethernet hub, or use an Ethernet crossover cable to connect the controller directly to a computer. Caution To prevent data loss and to maintain the integrity of your Ethernet installation, do not use a cable longer than 100 m. If you are using 100 Mbps Ethernet, Na
Streszczenie treści zawartej na stronie nr. 18
Wiring Power to the cFP-22xx The cFP-22xx requires an external power supply that meets the specifications in the Power Requirements section. The cFP-22xx filters and regulates the supplied power and provides power for all of the I/O modules. You must connect a power supply to at least one pair of V and C terminals. Optionally, you can connect a power supply to the other pair of V and C terminals. The controller draws power from the power supply with the higher voltage. The controller has on
Streszczenie treści zawartej na stronie nr. 19
2. Install a tie wrap or other device on the power wires to secure the ferrite in place near the controller power connector, as shown in Figure 24. Figure 24. Ferrite Installed with Tie Wrap 3. Connect the positive lead of the power supply to the V1 terminal of the COMBICON connector shipped with the cFP-22xx. 4. Connect the negative lead of the power supply to one of the C terminals of the COMBICON connector. 5. Optionally, connect the positive lead of another power supply to the V2 termin
Streszczenie treści zawartej na stronie nr. 20
Note The controller indicates which terminal it is using on the channel called Power Source in software. A value of 0 indicates V2, and a value of 1 indicates V1. This behavior is different from that of older Compact FieldPoint controllers. If your application uses input from the Power Source channel, you must change your application to reflect the change in channel behavior. You can either make the change in software or connect the primary power supply to V2 and a backup power supply to V1
