Streszczenie treści zawartej na stronie nr. 1
Model 8360 Owner’s Manual
(Ether card for the Model D2424 / D2424LV)
Table of Contents
Introduction ...............................................................................2
Installing the ether card ............................................................2
FTP client application ...............................................................2
Connecting to a personal computer .......................................3
One to one connection ..............................................
Streszczenie treści zawartej na stronie nr. 2
Introduction There is the possibility of damaging the hard disk when Thank you very much for purchasing the Fostex transporting the recorder. Before transporting the re- corder to our service department for the installation of product. the Ether Card, remove the hard disk from the recorder. The Model 8360 is an ether card dedicated for the Be sure to keep the removed hard disk carefully. D2424/D2424LV digital multitrack recorder. By installing the 8360 to the recorder, it can be used as a
Streszczenie treści zawartej na stronie nr. 3
Connecting to a personal computer There are two types for connecting the recorder to a personal computer using the LAN cable; one to one connection and LAN connection. The following describes how to make connection for each type. One to one connection To connect the recorder to a personal computer on a "one to one" basis, use a "cross cable of category 5 or higher" for connection between the recorder and a personal computer, as shown below. To use the ether card as an FTP server, see "TCP/IP set
Streszczenie treści zawartej na stronie nr. 4
Connection to an existing LAN To connect the recorder to an existing LAN, use a "straight cable of category 5 or higher" for connection between the recorder and a hub, as shown below. When connecting the recorder to an existing LAN, set the IP address and subnet mask correctly. Other- wise, whole LAN system may have a trouble. Before setting the IP address and subnet mask, consult the network administrator. To use the ether card as an FTP server, see "TCP/IP setting (recorder's initial se
Streszczenie treści zawartej na stronie nr. 5
TCP/IP setting (recorder's initial setting) Make the settings in the "TCP/IP Setup?" menu which is added to the setup mode of the recorder so that the Model 8360 can be used as an FTP server. SETUP 1. Turn on the recorder's power. flashing 2. Press the [SETUP] key to enter the setup mode. SETUP 3. Use the JOG dial to bring up the "TCP/IP Setup?" menu and press the [EXECUTE/YES] key. The first time you enter the TCP/IP setup mode, the display flashing shows the screen for selecting the ether mode
Streszczenie treści zawartej na stronie nr. 6
IP address setting Subnet mask setting You must set the subnet mask value for the recorder. You must set the IP address for the recorder. 1. Use the JOG dial to bring up "Sub net.?" and press the 1. Use the JOG dial to bring up "IP Addr.?" and press the [EXECUTE/YES] key. [EXECUTE/YES] key. The display shows the screen for entering the subnet mask. The display shows the screen for entering the IP address. By default, it is set to "0. 0. 0. 0" and the leftmost 0 flashes. By default, it is set to
Streszczenie treści zawartej na stronie nr. 7
Anonymous setting Login name (password) setting The login name and password are used when ac- This setting selects whether the 8360 checks the cessing (logging in) to the recorder from a personal user name and password or not when logging in. computer. The 8360 allows to set a set of the login If it is set to "ON", the 8360 does not check the user name and password. name and password, so you can access (log in) to the recorder with any user name and password (in- cluding no name/password)
Streszczenie treści zawartej na stronie nr. 8
3. After entering the login name, press the [EXECUTE/YES] Ether mode setting key. The display now shows the screen for entering a password, To activate the communication function of the where the leftmost digit flashes initially. Model 8360, you must set the ether mode to "ON". SETUP The settings previously described become effective when the ether mode is set to "ON". flashing 4. Enter a password in the same manner as entering a password. 1. Use the JOG dial to bring up "EtherMode?" and
Streszczenie treści zawartej na stronie nr. 9
Personal computer setting Setting for connection After completing the "TCP/IP Setup?" setting for the Activate the FTP application and make setting for con- nection as described below according to the application. recorder, set the TCP/IP and connection settings for the personal computer. [for WS-FTP] • Profile Name: Enter a desired name. • HostName/Address: [192. 168. 0. ***] TCP/IP setting *** must be the same number as set for the recorder. Set the IP address and subnet mask of the personal c
Streszczenie treści zawartej na stronie nr. 10
Transferring files On the personal computer monitor, you can see the file con- After making all necessary settings described ear- figuration of the recorder in the FTP application window. In lier, make the following setting for the FTP applica- the following example, programs 1 and 2 are recorded onto the recorder. (Note that, depending on the FTP application, tion you use before opening the connection to trans- the appearance is different.) fer fil
Streszczenie treści zawartej na stronie nr. 11
Putting files to the recorder Notes on transferring files 1. A file name must be "tr (track number).wav". Other file 1. Log in to the D2424/D2424LV from the personal computer names cannot be accepted. via the network. 2. Only a mono-track, 16/24-bit, 96/88.2/48/44.1-kHz WAV 2. Select the program folder to which you are going to put the file can be transferred (for both direction). file. 3. If a track WAV file, which has the different quantization bit If you want to put the file to a new program,
Streszczenie treści zawartej na stronie nr. 12
Declaration of EC Directive This equipment is compatible with the EMC Directive (89/336/EEC) - Directive on approximation of member nation's ordinance concerning the electromagnetic compatibility. This equipment is compatible only when connected to fostex specified product. The Affect of Immunity on This Equipment The affect of the European Specification EN50082-1 (coexistence of electromagnetic waves - common immunity specification) on this equipment are as shown below. In the electrical fast
