Streszczenie treści zawartej na stronie nr. 1
TM
TM
TM
USER GUIDE
1
Streszczenie treści zawartej na stronie nr. 2
IMPORTANT Please read this manual carefully before using your mixer for the first time. © Harman International Industries Ltd. 2007 All rights reserved Parts of the design of this product may be protected by worldwide patents. Part No. ZM0358-02 Soundcraft is a trading division of Harman International Industries Ltd. Infor- mation in this manual is subject to change without notice and does not repre- sent a commitment on the part of the vendor. Soundcraft shall not be liable for any loss or dama
Streszczenie treści zawartej na stronie nr. 3
Contents IMPORTANT SAFETY INSTRUCTIONS 4 SAFETY SYMBOL GUIDE 6 INTRODUCTION 7 THE 60-SECOND GUIDE 8 WIRING UP 10 BLOCK DIAGRAM 14 MONO INPUT CHANNELS 15 STEREO INPUT CHANNELS 18 MASTER SECTION 20 Lexicon® FX PROCESSOR OVERVIEW 24 FX OPERATION 24 FX PROCESSOR CONTROLS 25 REVERBS 26 REVERB CONTROLS 27 DELAYS 28 DELAY CONTROLS 28 MODULATED EFFECTS 29 FACTORY RESET 31 EFFECTS DATA CHART 32 USING YOUR MFX CONSOLE 33 MARK-UP SHEETS 35 FITTING OPTIONAL RACK-MOUNT BRACKETS 36 DIMENSIONS 37 APPLICATIONS
Streszczenie treści zawartej na stronie nr. 4
IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of a polarised or grounding type plu
Streszczenie treści zawartej na stronie nr. 5
with liquids, such as vases, on the apparatus. No naked flame sources, such as lighted candles, should be placed on the apparatus. Ventilation should not be impeded by covering the ventilation openings with items such as newspapers, table cloths, curtains etc. THIS APPARATUS MUST BE EARTHED. Under no circumstances should the safety earth be disconnected from the mains lead. The mains supply disconnect device is the mains plug. It must remain accessible so as to be readily operable when the app
Streszczenie treści zawartej na stronie nr. 6
For your own safety and to avoid invalidation of the warranty please read this section carefully. SAFETY SYMBOL GUIDE For your own safety and to avoid invalidation of the warranty all text marked with these symbols should be read carefully. WARNINGS The lightning flash with arrowhead symbol, is intended to alert the user to the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of suffi- cient magnitude to constitute a risk of electric shock to persons. CAUTI
Streszczenie treści zawartej na stronie nr. 7
INTRODUCTION Thank you for purchasing a Soundcraft MFX mixer. The MFX range is our most cost- effective mixing solution, bringing you all the features and performance that you expect from a Soundcraft product, at an extraordinarily low price. The packaging, which your MFX arrived in, forms part of the product and must be retained for future use. Owning a Soundcraft console brings you the expertise and support of one of the industry’s leading manufacturers, and the results of nearly 3 decades of
Streszczenie treści zawartej na stronie nr. 8
THE 60-SECOND GUIDE To get you working as fast as possible, this manual begins with a 60-second guide. Here you can find quick information on any feature of the console. 1 MIC INPUT (XLR) Connect Microphones here. If you are using a condenser mic, ensure phantom power is supplied by pressing the switch at the top of the master section. WARNING: Do Not apply Phantom Power before connecting a microphone. 2 LINE INPUT (¼” Jack) Connect Line level sources here, e.g. Synth, Drum Machine, DI etc. 3
Streszczenie treści zawartej na stronie nr. 9
12 PFL When pressed the signal will appear on the monitor and headphone outputs - use this to monitor the post-EQ signal from the channel. 13 MIX/SUB SWITCH When this switch is up, the channel’s post-pan-pot signal is routed to the Mix (left and right) buses. When the switch is depressed, the post-pan-pot signal is routed to the Sub-group (left and right) buses. 14 SP LED The SP LED glows when a signal is present. The feed point for the LED is post-EQ, pre-mute. 15 INPUT CHANNEL FADER This is us
Streszczenie treści zawartej na stronie nr. 10
WIRING UP Mic Input The MIC input accepts XLR-type connectors and is designed to suit a wide range of BALANCED or UNBALANCED low-level signals, whether from deli- cate vocals requiring the best low-noise performance, or drum kits needing maximum headroom. Professional dynamic, condenser or ribbon mics are best because these will be LOW IMPEDANCE. While you can use low-cost HIGH IMPEDANCE mics, you do not get the same degree of immunity to interference on the microphone cable and as a result t
Streszczenie treści zawartej na stronie nr. 11
A ‘Y’ lead may be required to connect to equipment with separate send and return jacks as shown below: Stereo Inputs STEREO 1/2 These accept 3-pole 6.35mm (1/4") jacks, or 2-pole mono jacks which will automatically ground the ‘cold’ input. Use these inputs for sources such as keyboards, drum machines, synths, tape machines or as returns from processing units. The input is BALANCED for low noise and immunity from interference, but you can use UNBALANCED sources by wiring up the jacks as shown
Streszczenie treści zawartej na stronie nr. 12
Polarity (Phase) You will probably be familiar with the concept of polarity in electrical signals and this is of particular importance to balanced audio signals. Just as a balanced signal is highly effective at cancelling out unwanted interference, so two microphones picking up the same signal can cancel out, or cause serious degradation of the signal if one of the cables has the +ve and -ve wires reversed. This phase reversal can be a real prob- lem when microphones are close together and you
Streszczenie treści zawartej na stronie nr. 13
PROBLEM SOLVING Basic problem solving is within the scope of any user if a few basic rules are followed. • Get to know the Block Diagram of your console (see page 14). • Get to know what all controls and/or connections in the system are supposed to do. • Learn where to look for common trouble spots. The Block Diagram is a representative sketch of all the components of the console, showing how they connect together and how the signal flows through the system. Once you have become familiar with th
Streszczenie treści zawartej na stronie nr. 14
BLOCK DIAGRAM 14
Streszczenie treści zawartej na stronie nr. 15
MONO INPUT CHANNELS 1 Mic Input The MIC input accepts XLR-type connectors and is designed to suit a wide range of BALANCED or UNBALANCED signals. Professional dynamic, condenser or ribbon mics are best because these will be LOW IMPEDANCE. You can use low-cost HIGH IMPEDANCE mics, but the level of background noise will be higher. If you turn the PHANTOM POWER on (top right-hand side of the mixer) the socket provides a suit- able powering voltage for professional condenser mics. ONLY connect co
Streszczenie treści zawartej na stronie nr. 16
The Send may also be tapped off as an alternative pre-fade, pre-EQ direct output if required, using a lead with tip and ring shorted together so that the signal path is not interrupted (see below). 5 Gain This knob sets how much of the source signal is sent to the rest of the mixer. Too high, and the signal will distort as it overloads the channel. Too low, and the level of any background hiss will be more noticeable and you may not be able to get enough signal level to the output of the mixer
Streszczenie treści zawartej na stronie nr. 17
POST-FADE), but for Foldback or Monitor feeds it is important for the send to be independent of the fader (this is called PRE-FADE). AUX SENDS 1 and 2 are both globally switchable between pre and post-fade (see master section on page 20). 8 FX SEND This control sets the level of the post-fade signal being sent to the FX bus; from there it is routed to the FX processor. The FX Send is always post-fader. 9 PAN This control sets the amount of the channel signal feeding the Left and Right MIX buses,
Streszczenie treści zawartej na stronie nr. 18
STEREO INPUT CHANNELS 1 INPUTS STEREO 1/2 These inputs accept 3-pole 6.35mm (1/4") jacks. Use these inputs for sources such as keyboards, drum machines, synths, tape machines or processing units. The inputs are BALANCED for low noise and top quality from professional equipment, but you can use UNBALANCED sources by wiring up the jacks as shown in the ‘Wiring Up’ section earlier in this manual, although you should then keep cable lengths as short as possible. Mono sources may be used by pluggi
Streszczenie treści zawartej na stronie nr. 19
7 MUTE All outputs from the channel are enabled when the MUTE switch is released and muted when the switch is down. The MUTE switch’s inbuilt LED glows when the chan- nel is muted. 8 FADER The 60mm FADER gives you smooth control of the overall signal level in the channel strip, allowing precise balancing of the various source signals being mixed to the Master Section. It is important that the input level is set correctly to give maximum travel on the fader which should normally be used at aroun
Streszczenie treści zawartej na stronie nr. 20
MASTER SECTION 20
