Streszczenie treści zawartej na stronie nr. 1
SPECO TECHNOLOGIES KEYBOARD CONTROLLER
KBD-927
Instruction Manual
L
Please read this manual thoroughly before use and keep it handy for future reference.
Rev.040130
Streszczenie treści zawartej na stronie nr. 2
WARNING AND CAUTION WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ON THE EQUIPMENT. CAUTION EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the pr
Streszczenie treści zawartej na stronie nr. 3
FCC COMPLIANCE STATEMENT FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY
Streszczenie treści zawartej na stronie nr. 4
IMPORTANT SAFEGUARDS 1. READ INSTRUCTIONS -- All the safety and operating 10. POWER CORDS -- Do not allow anything to rest on the instructions should be read before the appliance is operated. power cord. Do not locate video monitor or equipment where the cord will be abused by persons walking on it. 2. RETAIN INSTRUCTIONS -- The safety and operating instructions should be retained for future reference. 11. HEED WARNINGS -- Follow all instructions marked on the v
Streszczenie treści zawartej na stronie nr. 5
Table of Contents Chapter 1.0 INTRODUCTION 1.1 Features 1.2 Unpacking Chapter 2.0 INSTALLATION 2.1 Connection Diagram 2.2 Dip Switch Setting 2.3 Keyboard Setup 2.4 Install with ADR series 2.5 Install with SDR series 2.6 Install with IDR series Chapter 3.0 OPERATION 3.1 Multiplexer Control 3.2 Keyboard Lock/Unlock 3.2 Summary of Keyboard Control Appendix A Trouble Shooting Appendix B SPECIFICATION 5
Streszczenie treści zawartej na stronie nr. 6
Chapter 1 INTRODUCITON 1.1 Features This keyboard controller is capable to control 32 FastraxII dome cameras and remote control functions for variety of external switching devices like Multiplexer(max 255), Digital Video Recorder(max 99) etc… The keyboard controller features: • The capability of control a camera’s panning and tilting movement with variable speed from 0.5 °/sec to 90 °/sec as well as its zoom, focus, and iris command. Normal speed is inversely proportional to the cur
Streszczenie treści zawartej na stronie nr. 7
1.2 Unpacking Unpack the equipment and make sure all listed items are included in the box. Contents of Keyboard box Keyboard controller ------------------------------- 1 Junction box --------------------------------------- 1 3m cable -------------------------------------------- 2 M4 Self tapping screws ------------------------- 4 Instruction manual --------------------------------- 1 12VDC SMPS -------------------------------------- 1 7
Streszczenie treści zawartej na stronie nr. 8
Chapter 2 INSTALLATION 2.1 Connection Diagram 2.1.1 Basic Installation Diagram POWER AC 24V AWG # 24 SIREN POWER AC 24V RS-485 HALF DUPLEX MODE : TX+,TX- LIGHT ALARM OUTPUT SENSOR UP TO 4 ALARM INPUT UP TO 8 ALARM INPUT ALARM INPUT 5~8 1~4 BNC ALARM OUTPUT ALARM OUTPUT 1~2 3~4 (RS-422) MONITOR RS-422 SIMPLEX MODE : TX+,TX- DUPLEX MODE : TX+,TX-,RX+,RX- BNC Figure 2 – Basic installation diagram 8 AC+ AC- FGND (RX+) (RX+) (RX-) (RX-) DOME1 + RX+(TX+) RX+(TX+) RS-485 RX-(TX-) RX-(TX-) DO
Streszczenie treści zawartej na stronie nr. 9
2.1.2 Single Multiplexer POWER POWER POWER AC 24V AC 24V AC 24V AWG # 24 (RS-422) BNC SPOT MONITOR MAIN MONITOR BNC BNC MULTIPLEXER RS-485(+) PIN No.4 RS-485(-) PIN No.5 Figure 3 – Single Multiplexer 9 AC+ AC- FGND (RX+) (RX+) (RX-) (RX-) RX+(TX+) RX+(TX+) RS-485 RX-(TX-) RX-(TX-) GND AC- AC+ NO4 NO2 NC4 NC2 COM4 COM2 NO3 NO1 NC3 NC1 COM3 COM1 GND GND AL8 AL4 AL7 AL3 GND GND AL2 AL6 AL5 AL1
Streszczenie treści zawartej na stronie nr. 10
2.1.3 Single User with Two Multiplexer POWER POWER POWER AC 24V AC 24V AC 24V AWG # 24 (RS-422) BNC 1ST MAIN MONITOR SPOT MONITOR 2ND MAIN MONITOR BNC BNC BNC 1ST MULTIPLEXER 2ND MULTIPLEXER RS-485(+) PIN No.4 RS-485(-) PIN No.5 Spot output of the first multiplexer to be th connected to 16 input of the second multiplexer. nd And first spot output of the 2 multiplexer to be connected to the spot monitor. You will see the picture of the selected camera (1~31) on spot monitor by selecting
Streszczenie treści zawartej na stronie nr. 11
2.1.4 Two Multiplexer with Slave Keyboard Controller POWER POWER POWER AC 24V AC 24V AC 24V AWG # 24 (RS-422) BNC SPOT MONITOR SPOT MONITOR 1ST MAIN MONITOR FOR SLAVE K/B FOR MASTER K/B 2ND MAIN MONITOR BNC BNC BNC 1ST MULTIPLEXER 2ND MULTIPLEXER RS-485(+) PIN No.4 RS-485(-) PIN No.5 th Spot output 1 of the first multiplexer to be connected to 16 input of the second multiplexer. th th nd th n: User, Spot out of n to be connected to (15-n) camera input of the 2 multiplexer. n spot nd
Streszczenie treści zawartej na stronie nr. 12
2.2 Termination & Dip Switch Setting The first and last devices in an installation (dome and keyboard controller) must have the data line terminated by setting the DIP switch. Without proper termination, there is potential for control signal errors. Total length of the cable for communication should not exceed 1 mile. Refer to Figure 7 for setting the dome camera and keyboard controller termination. Cable for communication More than two branches require repeater (HID2404SR) which
Streszczenie treści zawartej na stronie nr. 13
Sub- Multi- DOME controll plexer Termination Controller er 1 2 3 4 5 6 7 8 ON ON ON ON SLAVE ON Factory reserved Use OFF OFF OFF OFF MASTER OFF Table 1 - S1 Switch Setting 2.3 Multiplexer Control Duplex setup: NOTE: Multiplexers require a new ROM version to be controlled by the keyboard controller. The new multiplexer ROM accepts control instructions from the keyboard controller. If your multiplexer’s serial number is M104xxxx or higher, then it is ready to accept con
Streszczenie treści zawartej na stronie nr. 14
Unit address: 001 ~ 128 Protocol: B1 2.4 Keyboard Setup User need to setup network, passwords and special functions such as Uploading and Downloading programmed data from the dome cameras. To enter the Keyboard menu, press Ctrl + Menu. You will see the following menu. Joystick Up/Down scrolls menu items, push the stick to Right to enter the sub-menu. Configuration Network Data Bank Alarm Exit Configuration - Key Beep : ON - enable key beep sound, OFF - Disable beep s
Streszczenie treści zawartej na stronie nr. 15
- Com Ports Select the device to be connected on selected port. Dome : None/Dome … MUX : None/DUPLEX/TRIPLEX/AUX IN/AUX I/O… DVR485 : None/ADR/SDR/IDR/AUX IN/AUX I/O… DVR232 : None/ADR/SDR/IDR/AUX IN/AUX I/O… Save and Exit Save the programmed data and return to the previous Menu (Exit without saving if you press ESC key) Note) AUX IN : auxiliary signal input ( simplex mode)
Streszczenie treści zawartej na stronie nr. 16
AC + AC - AC + AC - FG ND (R x+ ) (R x- ) R x+( Tx+) Tx + R x-( Tx-) Tx - GND GND FASTRAX-2L Vxxx Slave ID = 1 ← Current Device ID = 1 Input Password : xxxx ← Default setting is 9999 for administrator 1111 for user CAM:000 3. Press Ctrl + Menu. Set the Slave ID to 01 4. Set Slave Node to “B” in case that master keyboard model is KBD-927(N : NTSC,P : PAL) Slave ID = 1 Slave Node : A/B ← A : KBD-927 RS485 Protocol Half duplex mode Tx-,Tx+ NO4 NO2 NC 4 NC 2 COM4 COM
Streszczenie treści zawartej na stronie nr. 17
A. Switch the keyboard controller ON B. Input password (Factory setting is 9999) C. Open the menu of the keyboard controller by pressing Ctrl + Main Key. D. Set as below in Network menu. Set Baud Rate Dome : 9600 Mux : 9600 DVR485 : 9600 DVR232 : 9600 Com Port Dome : Dome Mux : None DVR485 : AUX IN DVR232 : ADR 4) How to setup ADR - Switch the ADR on. - Press the Menu button. Input password according to the instruc
Streszczenie treści zawartej na stronie nr. 18
Select “Camera” on the Device menu. Unit ID should be 1 up to 99. Unit ID is not allowed number “0”. Set “PTZ Device” and “ID” of the dome camera. Select RS232/RS485 after PTZ is installed, and then set-up as below table. 18
Streszczenie treści zawartej na stronie nr. 19
RS232/RS485 Baud Rate Parity Data Stop Usage RS232 9600 None 8 1 Remote Control RS485 9600 None 8 1 PTZ Control 5) After setting Unit ID, Camera, and RS232/RS485, installing dome camera is basically completed. Please refer to the manual of ADR for the other installation. 6) Press the related number of the controller which is correspondent to unit ID of ADR. Then press DVR button and adjust unit ID of the controller 7) Make sure if any change is appeared on screen when you press
Streszczenie treści zawartej na stronie nr. 20
D. Set as below in Network menu. Set Baud Rate Dome : 9600 Mux : 9600 DVR485 : 9600 DVR232 : 9600 Com Ports Dome : Dome Mux : None DVR485 : AUX IN DVR232 : SDR 4) How to setup SDR - Switch the SDR on. - Press the Menu button. Input password according to the instruction. (Factory setting is 4321) - If the below screen is appeared, set “Quick Setup” to “Off”. If press OK after putting Quick Setup to off status, the belo
