Streszczenie treści zawartej na stronie nr. 1
Outdoor Pan/Tilt Head
AW-PH650N
Before attempting to connect, operate or adjust this product,
please read these instructions completely.
Printed in Japan
D
F0406Y1056 VQTB0104-1
Streszczenie treści zawartej na stronie nr. 2
Safety precautions FCC Note: CAUTION This equipment has been tested and found to comply RISK OF ELECTRIC SHOCK with the limits for a class A digital device, pursuant to DO NOT OPEN Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). interference when the equipment is operated in a NO USER SERVICEABLE PARTS INSIDE. commercial environment. This equipment generates
Streszczenie treści zawartej na stronie nr. 3
Safety precautions IMPORTANT SAFETY INSTRUCTIONS Read these operating instructions carefully before using the unit. Follow the safety instructions on the unit and the applicable safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 10) Protect the power cord form being walked on or pinched particularly at plugs, convenience 2) Keep these instructions. receptacles, and the point where they exit from 3) Heed all warnin
Streszczenie treści zawartej na stronie nr. 4
Contents Introduction ....................................................................... 4 How to install the camera .............................................. 17 How to install the housing ............................................. 24 Accessories ...................................................................... 4 Connections .................................................................... 25 Precautions for use ........................................................
Streszczenie treści zawartej na stronie nr. 5
Installation precautions Do not install this unit by suspending it, and do not install Be absolutely sure to use w ater-proof connecting cables. it on its side. Do not install the unit where the temper ature will drop While f actoring in the weights of the unit and the load that below –4°F (–20°C) or rise above 113°F (45°C) since the unit will bear, select an installation location which is operation will become unstable under these temperature conducive to fastening the unit securely
Streszczenie treści zawartej na stronie nr. 6
Mounting (Pan/tilt head) Precautions for installation How to install Do not install this unit b y suspending it, and do not install Attach one end of the anti-fall wire to the mounting hole, it on its side. and secure the other end to the mounting base or other sturdy place. Using the f our pan/tilt head mounting holes, fasten the The diameter of the hole where the anti-fall wire is unit securely with bolts which are long enough. attached is 6.5 mm. Attach the wire using the anti-f
Streszczenie treści zawartej na stronie nr. 7
Mounting (AC adapter) Precautions for installation Be sure to use water-proof connecting cables. Be sure to keep AC power switched off during installation and connection. Bef ore pressing the power switch on, make sure that all parts, including the housing and pan/tilt head, have been installed and connected completely and free of errors. Do not install the A C adapter at a cold place [below –4°F (–20°C)] or a hot place [over 113°F (45°C)] because extremely low or high temperature wi
Streszczenie treści zawartej na stronie nr. 8
Mounting (AC adapter) Connect the cables. (Refer to the “Connections”.) Make the distance between the AC adapter and pan/tilt head less than the length (30 m) of the power cable supplied. Pan/tilt head AC power input Ventilation opening Pole mounting plate 8
Streszczenie treści zawartej na stronie nr. 9
Parts and their functions Main unit (Pan/tilt head) Main unit cover Option connector [OPTION] The sunshade cover and main unit cover must be The control signals of the controller’s OPTION button are removed when the cable compensation circuit or landing output from this connector. characteristics are to be changed. Be absolutely sure to use a water-proof cable. The compatible connector is the R28-P8M4.8 made by Grip Tajimi Electronics Co., Ltd. OPTION Used i
Streszczenie treści zawartej na stronie nr. 10
Parts and their functions Housing unit Camera housing control board Wiper blade Connect the supplied camera cable. Replace the wiper blade when it can no longer wipe off waterdrops well. Air filter How to replace it: Raise the blade at the center, pull it up Air is taken in through the air filter. Replace it when it is and off, and fit a new blade in its place. clogged up. After replacing the blade, check that the ( Whenever
Streszczenie treści zawartej na stronie nr. 11
Parts and their functions AC adapter unit DC power unit AC power input terminal board This unit supplies a DC output of 15 V, 10 A (maximum) This terminal board is for connecting AC input power. when an AC input of 120 V is supplied. (AC 120 V, 60 Hz, 120 W) Power switch [POWER ON/OFF] AC adapter mounting screw holes (×4) This switch is used to supply AC power to the DC power Attach the supplied pole mounting plate to these screw
Streszczenie treści zawartej na stronie nr. 12
Parts and their functions Supplied cable unit (VEEB0133) 24P round water-proof plug (male) G/L IN BNC jack Connect this to the multi connector [MULTI] on the main This is the gen-lock signal input jack. unit. Use a BNC coaxial cable for the connecting cable. RJ-45 modular plug D-SUB 15P connector (male) Connect this to pan/tilt head controller. Connect the controller used for the multi purpose camera It can be extended up to 3281 ft. (1000 m). to thi
Streszczenie treści zawartej na stronie nr. 13
Parts and their functions (VEEB0152) 7P round water-proof plug (female) 7P round water-proof plug (male) Connect this to the power connector [POWER] on the Connect this to the DC output connector [DC 15V OUT] main unit. on the AC adapter. (VEEB0176) 26P connector (male) 50P connector (male) Connect this to the CAMERA I/F connector [CAMERA Connect this to the CAMERA I/F connector [CAMERA I/F] on the housing. I/F] on the convertible came
Streszczenie treści zawartej na stronie nr. 14
Installation Installing the housing mount frame Attach the housing mount frame (supplied) to the rotary arm of the main unit. Attach the housing mount frame to the rotary arm as shown in the figure below. The screws must be installed together with the flat washers and spring washers (supplied). · Using the supplied Allen key, install the frame securely to prevent looseness in the four places where the screws are used. Rotary arm Housing mount frame Allen key
Streszczenie treści zawartej na stronie nr. 15
Installation Cable compensation circuit settings When the pan/tilt head and controller have been connected, the maximum allowable length of the connecting cables is 3281 ft. (1000 m) for the 10BASE-T straight cable (UTP category 5) and coaxial cable (BELDEN 8281). However, when using the cables beyond a distance of 1640 ft. (500 m), set the cable compensation circuit to ON by following the steps. (The factory setting is OFF.) Remove the five screws used to attach the sunshade cover to kee
Streszczenie treści zawartej na stronie nr. 16
Installation CPU circuit board switch settings Set switches SW1, SW2 and SW3 on the CPU circuit board as follows. SW2 SW1 SW3 SW1 (Selector switch for landing characteristics) For a soft landing: Set SW1 to the left position (RP501). (Factory setting) For an exact landing: Set SW1 to the right position (RP605). SW2 Do not change the position of this switch. Continue to use it at the DESK TOP position. SW3 Do not change the position of this switch. Continue to use it at the RS-422
Streszczenie treści zawartej na stronie nr. 17
Installation How to install the camera Loosen the bolts f or opening and closing the top cover, Remo ve the camera mount. and open the top cover. Loosen the top cover open/close bolts Install the camera on the camera mount. The support arm completely enters the groove. Open the top cover until the support arm completely enters the groove. For details on how to install the camera and mount, refer Bear in mind that it will not be possible to lock the top to the instruction
Streszczenie treści zawartej na stronie nr. 18
Installation Use the 2 screws supplied with the camera to attach Attach the positioning screw (supplied) to the camera the mounting adapter (supplied with the camera) to mounting spacer . the top panel of the camera. Use the 2 screws (supplied) to attach the camera Attach the positioning scre w (supplied) to the camera mounting spacer to the fan mounting seat on the m
Streszczenie treści zawartej na stronie nr. 19
Installation Attach the positioning screw (supplied) to the camera Attach the positioning 1 screw (supplied) to the mounting spacer . camera mount . Use the 2 scre ws (supplied) to attach the camera Attach the camera mount to the fan mounting part mounting spacer to the fan mounting seat on the on the top panel of the camera using the 1 screw , flat top panel of the camera. washer
Streszczenie treści zawartej na stronie nr. 20
Installation Attach the positioning 1 screw (supplied) to the camera mount . Attach the camera mount using the 2 screws , flat washers and spring washers (supplied). (The camera mount points toward the front or back in the opposite way from a convertible camera. For pointing upward or downward, make sure that the two sides of the camera mount are higher — which is the opposite from when the AK-HC910 is used — than the central are
