Instrukcja obsługi PYLE Audio PDWM9000

Streszczenie treści zawartej na stronie nr. 1

AF RF AF RF
UHF PR O FE SSIO N A L
CH 02: 801 . 50M H z CH 02: 801 . 50M H z
W IREL ESS M ICRO PHO NE
R
PO W E
RECEIVER LCD CH. A MIN MAX RECEIVER LCD CH.A MIN MAX
PDWM9000 User’s Manual

Streszczenie treści zawartej na stronie nr. 2

Introduction Thank you for selecting the PDWM9000 Dual UHF PLL Synthesized Diversity System. Before operating please read this instruction manual carefully and thoroughly in order to understand the correct operating procedures and achieve the best results. The PDWM9000 is an advanced PLL synthesized UHF wireless system. Designed for professional applications, it has a 1U rackmount receiver, balanced XLR and unbalanced 1/4” connections. This system includes the following accessories: Audio Output

Streszczenie treści zawartej na stronie nr. 3

2. Installation of the Receiver ANT B ANT A AC: 110V/220V 50/60Hz OUT B MIX OUT OUT A DC12 Fig. 3 1. Power Connection Connect the AC power cable to the 110/220V AC jack (9) and the other end into an AC outlet. Check the voltage selector (10) as shown in Fig. 4. ANT A DC12 AC: 110/220V 50/60Hz Fig. 4 2. Audio Output Connection: (A) 1/4” Unbalanced Output: Connect a 1/4” cable from the unbalanced output jack (7) of the receiver to the input jack of the mixer or amplifier, as shown in Fig. 3. This

Streszczenie treści zawartej na stronie nr. 4

3. Extend antennas A & B. Make them perpendicular with the machine. 4. Push the power switch to turn on the unit. 5. Adjust the volume using the control knobs on the receiver. Receiver Location  The receiver should be placed more than 3 ft. above the floor and 3 ft. away from the wall.  Antennas should be fully extended for best reception. 3. Parts Name And Function (Microphone) 2 01:08 1.25 CH MHZ 1 5 3 4 1. Grill 2. Three position switch (on top). 3. LCD Display 4. Channel Selectors 5. Batte

Streszczenie treści zawartej na stronie nr. 5

4. Operation of the Microphone 1. Screw the battery box cover counter clockwise. Insert a 9v battery (check the polarity). 2. Turn on the microphone. 3. The microphone features a three position switch. Place the switch in Stand By (middle position) to mute the sound without turning off the mic. Frequency & Channel Listing Mic B Mic A NO. Frequency Range NO. Frequency Range 1 790.75MHz 1 801.25MHz 2 791.15MHz 2 801.55MHz 3 791.55MHz 3 801.85MHz 4 791.95MHz 4 802.15MHz 5 792.35MHz 5 802.45MHz 6 79

Streszczenie treści zawartej na stronie nr. 6

5. Troubleshooting 1. Unit does not turn on.  Make sure the power cable is connected properly.  Check the fuse.  Check the voltage selector 2. AF display moves, but there is no sound output.  Check volume level.  Check audio cable.  Check the settings on your amplifier 3. The effective receiving distance decreases.  Change batteries.  Check for any devices that may be causing interference. 4. Sound Quality Deteriorates  Change Batteries.  Check for any devices that may be causing inter

Streszczenie treści zawartej na stronie nr. 7

Microphone Specifications Transmitter Power: ...... 8.5mW Modulation Type: ....... FM, F3F Max Deviation:......... +25Khz Spurious Emission:...... >40dB (with carrier) Battery Voltage: ........ 9V Battery Life: ........... Approx. 8 Hours Noise Control:.......... Advanced Noise Reduction Circuitry 60H 14KH 0dB 40H 300H 1K 5K 10K 14K 20K 30K Diagram of AF Frequency Response Attention: 1. For best reception, always maintain line of site between the transmitter and receiver. 2. Avoid direct sunshin