Streszczenie treści zawartej na stronie nr. 1
Safety Instructions & Operator's Manual for Safety Instructions & Operator's Manual for
COMMERCIAL
MID-MOUNT
ZERO TURNING
HYDRO DRIVE
SERIES 1
MODELS
CZT19481KWV
MODEL NUMBER EXPLANATION
C ZT 19 48 1 KWV
MODEL DESIGNATION ENGINE TYPE
DRIVE SYSTEM TYPE SERIES DESIGNATION
ENGINE HP * MOWER DECK SIZE
C - Commercial Mid Mount 19 - Engine Horsepower 48 - 48" Mower Width KW - Kawasaki Engine
ZT - Zero Turning Hydro Drive 1 - Series Designation V - Over Head Valve
Thank you for buying a SNAPPER Produc
Streszczenie treści zawartej na stronie nr. 2
IMPORTANT SAFETY INSTRUCTIONS ! ! WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind an
Streszczenie treści zawartej na stronie nr. 3
IMPORTANT SAFETY INSTRUCTIONS ! ! PREPARATION SAFE HANDLING OF GASOLINE (Continued From Previous Page) (Continued From Previous Column) 3. Data indicates that operators age 60 and above, are 7. Remove gas-powered equipment from the vehicle or trail- involved in a large percentage of mower-related injuries. er and refuel it on the ground. If this is not possible, then These operators should evaluate their ability to operate refuel equipment using a portable container, rather than a the mower sa
Streszczenie treści zawartej na stronie nr. 4
IMPORTANT SAFETY INSTRUCTIONS ! ! OPERATION MAINTENANCE (Continued From Previous Page) (Continued From Previous Column) 16. On slopes, the weight of the towed equipment may cause 3. When draining fuel tank, drain fuel into an approved con- loss of traction and loss of control. When towing, travel tainer outdoors and away from open flame. slowly and allow extra distance to stop. 4. Check brakes frequently; adjust, repair or replace as 17. DO NOT operate engine in enclosed areas. Engine needed.
Streszczenie treści zawartej na stronie nr. 5
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-4 TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 SECTION 1 - FAMILIARIZATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 SECTION 2 -SAFETY MESSAGES AND SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . . . . .7-9 SECTION 3 - OPERATING INSTRUCTIONS . . .
Streszczenie treści zawartej na stronie nr. 6
Section 1 - FAMILIARIZATION BLADE SWITCH KEY SWITCH CHOKE CONTROL ENGINE SPEED HOUR METER CONTROL ROLL BAR PROTECTIVE SEAT BELT STRUCTURE MOTION CONTROL MOTION CONTROL LEVER LEVER RIGHT HAND FUEL TANK LEFT HAND FUEL TANK DECK LIFT LEVER PARKING BRAKE LEVER CONTROL PANEL (see inset) DISCHARGE DEFLECTOR IMPORTANT The figures and illustrations in this manual DECK LIFT PEDAL are provided for reference only and may differ from your specific model. Contact FIGURE 1.1 your Snapper dealer if you have qu
Streszczenie treści zawartej na stronie nr. 7
Section 2 - SAFETY MESSAGES AND SYMBOLS DANGER ! ROTATING PARTS KEEP AWAY FROM MOVING PARTS MOTION CONTROL LEVER OPERATION WEAR HEARING PROTECTION PARKING BRAKE LEVER OPERATION WARNING ! AVOID SERIOUS INJURY OR DEATH 7
Streszczenie treści zawartej na stronie nr. 8
Section 2 - SAFETY MESSAGES AND SYMBOLS CONTROL PANEL IDENTIFICATION DANGER! ROTATING BLADES KEEP CHILDREN AND OTHERS OUT OF MOWING AREA FUEL TANK SELECT RUN START STOP FUEL GAUGE (2) IGNITION SWITCH 8
Streszczenie treści zawartej na stronie nr. 9
Section 2 - SAFETY MESSAGES AND SYMBOLS ROLL BAR PROTECTIVE STRUCTURE DECALS 9
Streszczenie treści zawartej na stronie nr. 10
Section 3 - OPERA Section 3 - OPERATING INSTRUCTIONS TING INSTRUCTIONS 3.1 PRE-START CHECK LIST 3.1.8. Place mower in desired cutting height setting. Make the following checks and perform the service Grasp deck lift lever and move lever to desired cutting required before each start-up. height setting. Insert stop pin to desired cutting height. 3.1.1. Check tires and add or release air as needed to IMPORTANT: There is a foot assist pedal located to bring pressure to 12 psi in drive tires. Pressur
Streszczenie treści zawartej na stronie nr. 11
Section 3 - OPERA Section 3 - OPERATING INSTRUCTIONS TING INSTRUCTIONS ROLL RELEASE: To roll the machine without the 3.2 STARTING & STOPPING - ENGINE, BLADES, engine running, pressure within the hydraulic pumps PARKING BRAKE must be released. There is a hydraulic pressure relief valve on the upper side of each pump that is used to 3.2.1. STARTING ENGINE release the pressure. Use a wrench to rotate both relief When the ignition key is turned the engine will not start valves counter clockwise two
Streszczenie treści zawartej na stronie nr. 12
Section 3 - OPERA Section 3 - OPERATING INSTRUCTIONS TING INSTRUCTIONS 3.2.2. STOPPING ENGINE NOTE: Engaging parking brake prior to placing motion 1. Stop engine by turning key to "STOP" position. control levers in the neutral lock position will cause Move engine speed to the Turtle "SLOW" position and engine to die. See Figure. 3.8. turn key to "STOP". See Figure 3.6. 2. Release parking brake by pushing parking brake lever forward to the released position. See Figure 3.9. KEY SWITCH SHOWN FROM
Streszczenie treści zawartej na stronie nr. 13
Section 3 - OPERATING INSTRUCTIONS 3.3 CUTTING HEIGHT ADJUSTMENT 3.4 OPERATION- MOTION CONTROLS 1. Adjust cutting height, as desired, to any position, This machine is equipped with dual hydrostatic wheel drive using deck lift lever. IMPORTANT: There is a foot transmissions. Each hydro pump is controlled by a sepa- assist pedal located to the right front side of the rate motion control lever. The left lever controls the left footrest. Always use this assist pedal to raise or lower wheel drive hyd
Streszczenie treści zawartej na stronie nr. 14
Section 3 - OPERATING INSTRUCTIONS 3.4.2. STOPPING MACHINE 5. Raise and lock roll bar as soon as clearance per- 1. Return motion control levers to the neutral position mits. & the neutral lock position. IMPORTANT: DO NOT use seat belt when roll bar is IMPORTANT: Operator must use hand assistance to folded. bring both motion control levers to the neutral position & the neutral lock position. ! WARNING ! There is no roll-over protection when roll bar is folded. 3.6 SAFETY INTERLOCK SYSTEM CHECKS T
Streszczenie treści zawartej na stronie nr. 15
Section 3 - OPERA Section 4 - MAINTENANCE TING INSTRUCTIONS 4.1 INTRODUCTION 4. Fill engine crankcase with new oil. Refer to your To retain the quality of the SNAPPER mower, use gen- engine owner's manual for oil specifications. uine SNAPPER replacement parts only. Contact a 5. Change engine oil filter at every oil change. Refer local SNAPPER dealer for parts and service assis- to your engine owner's manual for service instructions. tance. For the correct part or information for a particu- l
Streszczenie treści zawartej na stronie nr. 16
Section 3 - OPERA Section 4 - MAINTENANCE TING INSTRUCTIONS 4.2.3. CHECK MOWER DRIVE BELT 4. Clean Mower Deck 1. Lower deck to lowest setting. a. Remove key from ignition switch. 2. Remove footrest. See Figure 4.3. b. Remove spark plug wire(s) and secure away from 3. Removal of footrest will allow access to mower spark plug(s). drive belt. c. Raise mower deck to its highest setting. It may be 4. Check the belt tension. If belt is frayed, slit, sev- necessary to raise mower deck higher using a e
Streszczenie treści zawartej na stronie nr. 17
Section 3 - OPERA Section 4 - MAINTENANCE TING INSTRUCTIONS 4.3.3. RIDING MOWER - LUBRICATION HYDRAULIC FLUID 1. Front Wheel Bearings RESERVOIR Lubricate with Kendall NLGI No. 2 lithium grease or equivalent, from a grease gun. See Figure 4.5. FIGURE 4.6 LUBRICATE CASTER LUBRICATE FRONT WHEEL BEARINGS WHEEL FIGURE 4.5 2. Hydro Pumps Check the level of the fluid in the fluid reservoir. Wipe away all dirt and debris from around reservoir cap before removing. Oil must remain absolutely clean! Check
Streszczenie treści zawartej na stronie nr. 18
Section 3 - OPERA Section 4 - MAINTENANCE TING INSTRUCTIONS 4.6 DECK REMOVAL ! WARNING ! Move power unit/mower deck to an area where the mower deck is to be disconnected. Turn engine "OFF" Allow engine to cool for at least ten minutes before and remove key from switch. Remove spark plug performing service or maintenance. DO NOT smoke wire(s) and secure away from spark plug(s). Move near fuel components when performing service or motion control levers to the neutral lock position. maintenance. D
Streszczenie treści zawartej na stronie nr. 19
Section 3 - OPERA Section 4 - MAINTENANCE TING INSTRUCTIONS 7. Remove bolts and nuts to disconnect both stabiliz- ! WARNING ! ers from mower deck and power unit. See Figure 4.12 and 4.13. DO NOT attempt any maintenance, adjustments or service with engine running. STOP engine. STOP blades. Set brake. Remove key. Remove spark plug wires and secure away from spark plugs. Engine and components are HOT. Avoid serious burns; allow suf- ficient time for all parts to cool. 4.6 DECK REMOVAL (Continued fr
Streszczenie treści zawartej na stronie nr. 20
Section 3 - OPERA Section 5 - ADJUSTMENTS & REP TING INSTRUCTIONS AIR ! WARNING ! Exercise EXTREME CAUTION when making this adjustment, due to close proximity of moving parts. REMOVE MOTION CONTROL LEVER CONNECTING ROD 5.1 NEUTRAL POSITION ADJUSTMENTS The motion control levers control the movement and stopping of the machine. Move the control levers to the center or neutral position to stop machine. IMPORTANT: Always return both motion control levers with hand assistance to the neutral posi- t
