Streszczenie treści zawartej na stronie nr. 1
Safety Instructions & Operator’s Manual for
21” STEEL DECK
WALK MOWERS
SERIES 17
MODELS
R215517HC
RP217017BV
RP215517HC
RP217017BVE
MR216517B
MRP216517B
MODEL NUMBER EXPLANATION
MR P 21 70 17 BV
MODEL DESIGNATION ENGINE DESIGNATION
SELF-PROPELLED SERIES DESIGNATION
CUTTING WIDTH ENGINE HORSE POWER
M – Model Designation P – Self Propelled Model 17 – Series Designation
R – Recycling Model 21 – 21” Cutting Width B – Briggs & Stratton H
Streszczenie treści zawartej na stronie nr. 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: This powerful cutting machine is capable of amputating hands and feet and can throw objects that can cause injury and damage! Failure to comply with the following SAFETY instructions could result in serious injury or death to the operator or other persons. The owner of the machine must understand these instructions and must allow only persons who understand these instructions to operate machine. Each person operating the machine must be of sound mind
Streszczenie treści zawartej na stronie nr. 3
IMPORTANT SAFETY INSTRUCTIONS SAFE HANDLING OF GASOLINE OPERATION (Continued From Previous Page) (Continued From Previous Column) 3. DO NOT remove fuel cap or add fuel with the engine 11. STOP engine and wait until the blade comes to running. Allow the engine to cool before refueling. complete STOP before removing grass bag and/or 4. DO NOT refuel the machine indoors. clearing grass. 5. DO NOT store the machine or fuel container inside 12. DO NOT operate mower without the entire grass
Streszczenie treści zawartej na stronie nr. 4
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS...................................................................... 2 - 3 TABLE OF CONTENTS......................................................................................................4 SECTION 1 - FAMILIARIZATION.......................................................................................5 SECTION 2 - OPERATING INSTRUCTIONS............................................................... 6-10 Pre-start Checklist.........
Streszczenie treści zawartej na stronie nr. 5
Section 1 - FAMILIARIZATION BRIGGS HONDA ENGINE ENGINE BLADE WHEEL DRIVE CONTROL SPEED SPEED CONTROL CONTROL CONTROL GROUND SPEED CONTROL CHOKE FAST IGNITION KEY FAST ROPE START HANDLE SLOW SLOW FUEL FILLER CAP OIL FILL CAP AND DIPSTICK ENGINE PRIMER REAR HEIGHT ADJUSTMENT LATCH GRASS BAG ADAPTER FRONT HEIGHT ADJUSTMENT LATCHES FIGURE 1.1 1.1 INTRODUC
Streszczenie treści zawartej na stronie nr. 6
Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST 2.2 STARTING & OPERATION Make the following checks and perform the service 2.2.1. ENGINE & BLADE required before each start-up. (Primer Models) 2.1.1. Check guards, deflectors, grass bag, adapter 1. Move engine speed control to the “Fast” (Rabbit) and covers to make sure all are in place and position. See Figure 2.3. securely tightened. IMPORTANT: Certain models do not have a 2.1.2. Check blade control and wheel drive contro
Streszczenie treści zawartej na stronie nr. 7
Section 2 - OPERATING INSTRUCTIONS 2.2 STARTING & OPERATION 2.2 STARTING & OPERATION 2.2.1. ENGINE & BLADE 2.2.1. ENGINE & BLADE (Choke Models) (Electric Start Models) 1. Move fuel shut off valve to the “ON” position. When the ignition key (Electric Start Switch) is turned See Figure 2.5. to “START”, the engine will not crank and will not start unless the blade control is engaged! NOTE: Stop the engine (and blade) by releasing the 1. Move engine speed control to the “Fast” (Rabb
Streszczenie treści zawartej na stronie nr. 8
Section 2 - OPERATING INSTRUCTIONS 2.4 HANDLE HEIGHT ADJUSTMENT 2.5 CUTTING HEIGHT ADJUSTMENT The height of the mower handle can be adjusted as 2. Set all wheels at the same cutting height. The follows: highest cutting position is Notch 6. The lowest 1. Loosen the lower nuts on each lower handle as cutting position is Notch 1. See Figure 2.10. shown in Figure 2.8. HIGHER LATCH LOWER POSITIONS HANDLE LOWER CUTTING HEIGHT SETTINGS LOOSEN LOWER NUTS ON EACH FIGURE 2.10 LOW
Streszczenie treści zawartej na stronie nr. 9
Section 2 - OPERATING INSTRUCTIONS 2.8 INSTALLATION of RECYCLING PLUG WARNING (Optional Accessory on Some Models) DO NOT attempt any maintenance, adjustments or STEP 1: Once adapter has been installed, recycling may service with engine and blade running. STOP engine be desired. Insert recycling plug completely and securely and blade. Disconnect spark plug wire and secure into adapter. Install grass bag. See Figure 2.12. away from spark plug. Engine and components are HOT. Avoid se
Streszczenie treści zawartej na stronie nr. 10
Section 2 - OPERATING INSTRUCTIONS WARNING DO NOT attempt any maintenance, adjustments or HOOK BAG HANDLE OVER LOWER service with engine and blade running. STOP engine HANDLES and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. 2.9 INSTALLATION of GRASS CATCHER – DOOR BAG (Optional accessory on some models) SLIDE CONNECTOR OVER END OF ADAPTER FLANGE M
Streszczenie treści zawartej na stronie nr. 11
Section 2 - OPERATING INSTRUCTIONS 2.14 INSTALLATION of RECYCLING COVER WARNING (Optional Accessory on Some Models) DO NOT attempt any maintenance, adjustments or It will be necessary to remove bag adapter and grass service with engine and blade running. STOP bag or discharge deflector before installing recycling cover. See previous section for instructions. Install the engine and blade. Disconnect spark plug wire and recycling cover and secure to the side and top of the secure away
Streszczenie treści zawartej na stronie nr. 12
Section 3 – MAINTENANCE HONDA ENGINE 3.1 INTRODUCTION To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention model and serial number. WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spa
Streszczenie treści zawartej na stronie nr. 13
Section 3 – MAINTENANCE 3.2.5. CHECK TRANSMISSION POLY-V BELT WARNING 1. Visually check poly-v belt for cracking, fraying, DO NOT attempt any maintenance, adjustments or severed or belt strands exposed. If worn or service with engine and blade running. STOP engine damaged, replace belt before operating mower. and blade. Disconnect spark plug wire and secure RECOMMENDED away from spark plug. Engine and components are BLADE RETAINING HOT. Avoid serious burns, allow sufficient time fo
Streszczenie treści zawartej na stronie nr. 14
Section 4 - REPAIR & ADJUSTMENTS 2. Replace the blade if it is badly chipped, bent, WARNING noticeably out of balance or has cracks or notch in DO NOT attempt any maintenance, adjustments or either tip. See Figure 4.1 & 4.1A. Replace with new service with engine and blade running. STOP engine blade. and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are WARNING HOT. Avoid serious burns, allow sufficient time for DO NOT use a cutting blade
Streszczenie treści zawartej na stronie nr. 15
Section 4 - REPAIR & ADJUSTMENTS CLUTCH CABLE WARNING DO NOT attempt any maintenance, adjustments or VINYL SPRING service with engine and blade running. STOP engine 1/16” TO 1/8” CLUTCH CABLE and blade. Disconnect spark plug wire and secure CLEARANCE EYE away from spark plug. Engine and components are UPPER SPRING HOT. Avoid serious burns, allow sufficient time for SPRING HOOK all components to cool. LOWER SPRING 4. Sharpen blade on a grinding wheel at an angle of 22 to 28 d
Streszczenie treści zawartej na stronie nr. 16
Section 4 - REPAIR & ADJUSTMENTS IMPORTANT: If machine drive system continues WARNING slipping see Trouble Shooting section. DO NOT attempt any maintenance, adjustments or USE service with engine and blade running. STOP engine NEEDLE and blade. Disconnect spark plug wire and secure NOSE PLIERS TO away from spark plug. Engine and components are INSTALL HOT. Avoid serious burns, allow sufficient time for DRIVE all components to cool. SPRING 4.3 DRIVEN AND DRIVE DISC SERVICE
Streszczenie treści zawartej na stronie nr. 17
Section 4 - REPAIR & ADJUSTMENTS WARNING 1/8” MEASUREMENT TO OUTSIDE EDGE OF DRIVE DO NOT attempt any maintenance, adjustments or DISC service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure DRIVE SLIDE DRIVEN DISC away from spark plug. Engine and components are DISC ASSEMBLY HOT. Avoid serious burns, allow sufficient time for TOWARD OUTSIDE all components to cool. EDGE 4.3.3. DRIVEN DISC ADJUSTMENT TRANSFER ROD (Continued From Pr
Streszczenie treści zawartej na stronie nr. 18
Section 4 - REPAIR & ADJUSTMENTS 4.3.5. Replacing Bearing In Driven Disc Assembly WARNING IMPORTANT: The bearing, on these machines, is DO NOT attempt any maintenance, adjustments or staked into the thrust plate. The bearing will have to be driven out with a mallet and a large punch. A new service with engine and blade running. STOP engine bearing with four retaining screws will have to be and blade. Disconnect spark plug wire and secure purchased to replace existing bearing. away fr
Streszczenie treści zawartej na stronie nr. 19
Section 4 - REPAIR & ADJUSTMENTS 4.4 BELT SERVICE WARNING On self-propelled mowers, the engine belt transmits DO NOT attempt any maintenance, adjustments or power from engine to drive disc. The drive disc powers the poly-v belt, which engages the service with engine and blade running. STOP engine transmission that powers the rear wheels. Should and blade. Disconnect spark plug wire and secure these belts become worn, they could cause slippage, away from spark plug. Engine and compone
Streszczenie treści zawartej na stronie nr. 20
Section 4 - REPAIR & ADJUSTMENTS PULLEY POSITION WARNING DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine DRIVE DISC and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are SLOT IN END HOT. Avoid serious burns, allow sufficient time for OF DRIVE DISC BOLT all components to cool. BUSHING 4.4.1. Engine Drive Belt Replacement (Stretch Type Belts) DECK BRACKET (PARTIALL
