Streszczenie treści zawartej na stronie nr. 1
#7600023 & 7600024 TWIN BAG CATCHER KIT FOR
38 & 42” SNAPPER / SIMPLICITY RZT RIDING MOWERS
7600023 TWIN BAG CATCHER KIT FOR 38” SNAPPER / SIMPLICITY RZT RIDING MOWER
7600024 TWIN BAG CATCHER KIT FOR 42” SNAPPER / SIMPLICITY RZT RIDING MOWER
WARNING
! !
DO NOT attempt any adjustments, maintenance, repairs, or service with engine running. Stop engine. Engage
parking brake. Remove key. Remove spark plug wire and secure wire away from spark plug. Engine, muffler and
surrounding areas are extremely
Streszczenie treści zawartej na stronie nr. 2
STEP 3: Remove the two innermost front carriage bolts securing the unit footrest to the frame. Install the four ballasts against the front of the machine, securing with the supplied 5/16 x 1-3/4” carriage bolts and lock nuts in place PLACE HOLE of those removed. Tighten hardware securely. See Figure 4. OVER TEE NUT AND SLIDE ADAPTER REMOVE EXISTING HARDWARE FORWARD ADAPTER LOCK FIGURE 6 NUT (2) c. Secure the front adapter mounting strap to the slots in the BALLASTS (4) anti-scalp wheel bracket
Streszczenie treści zawartej na stronie nr. 3
STEP 5: Install the bag adapter (42” Deck): b. Install the catcher support onto the unit, securing with the a. Remove the wing nuts, split lock washers, flat washers, hardware noted in Figure 11. Tighten all hardware securely. and hex nuts that secure the deflector to the deck, and NOTE: Be sure to reinstall any components that may have remove the deflector. See Figure 8. been removed when removing the hardware in Step 6a. SECURE WITH SECURE WITH REMOVE SUPPLIED 5/16 NUTS AND SUPPLIED 5/16 x 3/
Streszczenie treści zawartej na stronie nr. 4
STEP 8: Install the U-tube onto the top of the bagger chan- LOCK NUT (2) PAN HEAD nel, securing with three 5/16-24 x 1-5/8” curved head bolts, SCREW (2) COVER split lock washers, and hex nuts. See Figure 13. Tighten HANDLE hardware securely. CARRIAGE BOLT (4) CURVED HEAD BOLT (3) COVER HINGE U-TUBE FLAT WASHER (4) WASHER & LOCK NUT (4) NUT (3) FIGURE 15 BACK OF BAGGER CHANNEL STEP 11: Attach the cover assembly to the bagger channel FIGURE 13 by aligning the holes in the cover hinge with the top
Streszczenie treści zawartej na stronie nr. 5
STEP 12: Assemble the discharge tubes: a. Install one strap assembly to each of the locations marked ‘A’ in Figure 19. Insert one #10-24 x 5/8” pan head screw, fitted with one #10 x 1/2” OD flat washer, out through the hole in the tube or adapter. Secure with one #10 x 3/4” OD flat washer, strap, and #10-24 tee nut, tightening securely. See Figure 17. ATTACH TO ALL ‘A’ LOCATIONS (SEE FIGURE 19) FIGURE 19 c. Install the large end of the lower tube (short, straight tube) onto the end of the a
Streszczenie treści zawartej na stronie nr. 6
STEP 13: Assemble the grass containers: STEP 14: Flip open the cover assembly, then slide each a. Match the numbers on the side of each container container fully onto the U-tube assembly. See Figure 23. segment with its corresponding segment. ‘1’s and ‘2’s NOTE: Make sure that the warning label on the side of each designate the first container, ‘3’s and ‘4’s designate the container is facing out. second. See Figure 21. b. With the matched numbers aligned, insert the bottom COVER HANDLE SHOULD
Streszczenie treści zawartej na stronie nr. 7
Operation: WARNING ! ! To prevent injury or damage, always follow the operating instructions supplied with your machine when operating the bagger. To use the bagger: -Start the engine. -Move the throttle control to the fast position. -To fill the containers, always operate at a slow ground speed. To check and clean the discharge tubes: -Stop machine motion, turn off the blades, stop the engine. -Disconnect the straps securing the discharge tubes, and remove the tubes. -If needed, clear the disc
Streszczenie treści zawartej na stronie nr. 8
TWIN BAG CATCHER COMPONENTS - 38” RZT / JAVELIN 8
Streszczenie treści zawartej na stronie nr. 9
TWIN BAG CATCHER COMPONENTS - 38” RZT / JAVELIN ITEM NO. PART NO. QTY DESCRIPTION 1 7100658 1 ASSY., TWIN COVER - 38/42 7100659 1 COVER, TWIN - 38/42 1673320 4 RIVET, LARGE FLANGE - .188 X .617 1910531 4 WASHER, RIVET.188 (.20IDX.50OD) 1732490 4 FASTENER - PUSH DIA .25 X .70 1732488 1 SCREEN, TWIN COVER 1732489 1 SUPPORT, SCREEN - TWIN COVER 1732819 1 DECAL, WARNING 2 720524 1 HINGE, COVER 3 7091530 4 CARRIAGE BOLT, 1/4-20 X 3/4 3a 7091294 4 WASHER, SAE, 1/4 4 7091603 4 HEX CENTER LOCK NUT, 1/4-
Streszczenie treści zawartej na stronie nr. 10
TWIN BAG CATCHER COMPONENTS - 38” RZT / JAVELIN 10
Streszczenie treści zawartej na stronie nr. 11
TWIN BAG CATCHER COMPONENTS - 38” RZT / JAVELIN ITEM NO. PART NO. QTY DESCRIPTION 37 7091318 1 HEX HEAD CAP SCREW, 5/16 X 3/4 GR5 38 7300369 1 BAFFLE, 38" DECK - RZT 39 7060480 2 AIR LIFT KIT - COMPLETE 40 7037723 4 AIR LIFT 41 7090228 6 OVAL HEAD MACHINE SCREW, 5/16-24 X .656 42 7090391 6 INTERNAL TOOTH LOCK WASHER 5/16 43 7300367 4 BALLAST-TWIN BAG CATCHER - RZT 44 7900039 2 CARRIAGE BOLT, 5/16-18 X 1.75 GR5 11
Streszczenie treści zawartej na stronie nr. 12
TWIN BAG CATCHER COMPONENTS - 42” RZT / JAVELIN 12
Streszczenie treści zawartej na stronie nr. 13
TWIN BAG CATCHER COMPONENTS - 42” RZT / JAVELIN ITEM NO. PART NO. QTY DESCRIPTION 1 7100658 1 ASSY., TWIN COVER - 38/42 7100659 1 COVER, TWIN - 38/42 1673320 4 RIVET, LARGE FLANGE - .188 X .617 1910531 4 WASHER, RIVET.188 (.20IDX.50OD) 1732490 4 FASTENER - PUSH DIA .25 X .70 1732488 1 SCREEN, TWIN COVER 1732489 1 SUPPORT, SCREEN - TWIN COVER 1732819 1 DECAL, WARNING 2 720524 1 HINGE, COVER 3 7091530 4 CARRIAGE BOLT, 1/4-20 X 1/2 3a 7091294 4 WASHER, SAE, 1/4 4 7091603 4 HEX CENTER LOCK NUT, 1/4-
Streszczenie treści zawartej na stronie nr. 14
TWIN BAG CATCHER COMPONENTS - 42” RZT / JAVELIN 14
Streszczenie treści zawartej na stronie nr. 15
TWIN BAG CATCHER COMPONENTS - 42” RZT / JAVELIN ITEM NO. PART NO. QTY DESCRIPTION 36 7091613 2 PAN HEAD MACHINE SCREW, 5/16-18 X 3/4 37 7300386 1 BAFFLE, 42" DECK - RZT 38 7300367 4 BALLAST-TWIN BAG CATCHER - RZT 39 7900039 2 CARRIAGE BOLT, 5/16-18 X 1.75 GR5 15
Streszczenie treści zawartej na stronie nr. 16
INSTRUCTION No. 7100642 (Rev. 2, 12/14/2006) TP 200-5173-R2-AT-SN 16
