Streszczenie treści zawartej na stronie nr. 1
Vision Compact
350 Plus
For all customer enquiries or for replacement parts, contact:-
0870 609 1901
www.flymo.com
customer.services@husqvarna.co.uk
IMPORTANT INFORMATION
Read before use
& retain for future reference
Streszczenie treści zawartej na stronie nr. 2
Carton Contents start/stop levers switchbox Easi Reel cable winder cable winder attachment cable clip upper handle washer handle bolt knobs cable clip pack of 10 nuts washer bags electric cable with pin moulded plug bolt retaining clips cutting height spacers (1 fitted to lower handle lawnmower & 2 in loose parts pack pin instruction spanner/scraper manual tool IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTA
Streszczenie treści zawartej na stronie nr. 3
3. Do not use the lawnmower if the electric cables are 4. On slopes, be extra careful of your footing and wear damaged or worn non-slip footwear. 4. Immediately disconnect from the mains electricity sup- 5. Mow across the face of slopes, never up and down. ply if the cable is cut, or the insulation is damaged. Do 6. Exercise extreme caution when changing direction not touch the electric cable until the electrical supply on slopes. Walk never run. has been disconnected. Do not repair a cut or d
Streszczenie treści zawartej na stronie nr. 4
Assembly Instructions A B 1 2 1 3 C D 1 1 2 2 3. Fit the cable to the handle with the clips provided Lower Handle Assembly (A) 1. Lift the grassbox lid and remove the grassbox. (C3). Make sure the cable is not trapped 2. Insert the lower handle into the handle slots, between the upper and lower handles. ensuring that the holes are aligned. Cable Winder Assembly (C & D) 1. Insert cable winder attachment onto left upper 3. Insert the pins and secure with the retaining clips (A1). 4. Replace the gr
Streszczenie treści zawartej na stronie nr. 5
Starting and Stopping To Start your Lawnmower F G Your lawnmower uses an advanced belt drive sys- tem, between the motor and the blade which improves cutting power and flotation in all condi- tions. Due to the high turning force (Torque) which this motor develops a light squeak may be heard when the machine is started, this is quite normal and will not effect the performance of the product 1. Connect female extension cable connector to the back of the switchbox. (F) 2. Form loop in mains cable a
Streszczenie treści zawartej na stronie nr. 6
Removing and fitting the Blade and Fan Removing the Blade and Fan N 1. To remove the blade bolt, hold the fan firmly and blade bolt with the spanner provided loosen the blade bolt by turning it anti-clockwise (M). blade 2. Remove the blade bolt, blade, spacers and fan. (M) 3. Inspect for damage and clean as necessary. • Renew your metal blade after 50 hours mowing spacers or 2 years whichever is the sooner - regardless of condition. If the blade is cracked or dam- aged replace it with a new one.
Streszczenie treści zawartej na stronie nr. 7
Caring for your Lawnmower Cleaning T IMPORTANT: It is very important that you keep your lawnmower clean. Grass clippings left in any of the 1 2 3 air intakes or under the hood could become a poten- tial fire hazard. USE GLOVES. Switch off and remove the plug from the mains before cleaning. It is recommended that you clean your lawnmower straight after mowing while the grass is still wet. 1. Remove grass from under the hood with the spanner/scraper tool. (T1) U V 2. Remove the blade, see Figur
Streszczenie treści zawartej na stronie nr. 8
Fault Finding Hints Fails to Operate Poor Collection 1. Is the correct Starting procedure being followed? 1. Is the grassbox lid firmly closed? See ‘To Start your Lawnmower’ 2. Is the grassbox fitted correctly? 2. Is the Power Turned On? 3. Are you mowing correctly? 3. Check the fuse in the plug, if blown replace. 4. Check all air vents and openings are not obstructed. 4. Fuse continues to blow? 5. Raise to a higher height of cut. See ‘Adjusting the Immediately disconnect from the mains electr
Streszczenie treści zawartej na stronie nr. 9
Environmental Information Husqvarna Outdoor Products are manufactured under an Environmental Management System (ISO 14001) using, where practical, components manufactured in the most environmentally responsible manner, according to company procedures, and with the potential for recycling at the end of the products’ life. • Packaging is recyclable and plastic components have been labelled (where practical) for categorised recycling. • Awareness of the environment must be considered when disposing
