Streszczenie treści zawartej na stronie nr. 1
User’s Guide
CETTF10xx-105
Slide-in-Module Media Converter
• Ethernet
Copper to Fiber
10Base-T to 10Base-FL
Transition Networks CETTF10xx-105 series Ethernet
10Base-T to 10Base-FL media converters (designed
to be installed in a PointSystem™ chassis) connect
10Base-T twisted-pair copper cable to multimode or
single mode 10Base-FL fiber-optic cable.
Part Number Port One - Copper Port Two - Fiber-Optic
10Base-T 10Base-FL
CETTF1011-105 RJ-45 ST, 850 nm multimode, duplex
100 m (328 ft)* 2 km (1.2 mil
Streszczenie treści zawartej na stronie nr. 2
CETTF10xx-105 Installation Installation -- Continued CAUTION: Wear a grounding device and observe electrostatic discharge Install the Slide-in-Module precautions when setting the 4-position switch and the jumper and when CAUTION: Wear a grounding device and observe electrostatic discharge installing the media converter. Failure to observe this caution could result in precautions when installing the CETTF10xx-105 slide-in-module media damage to, and subsequent failure of, the media converter. c
Streszczenie treści zawartej na stronie nr. 3
CETTF10xx-105 Installation -- Continued Operation Connect the fber cable Status LEDs 1. Locate or build IEEE 803.2™ compliant 10Base-FL fiber cable with male, Use the status LEDs to monitor the media converter operation in the network two-stranded TX to RX connectors installed at both ends. PWR (Power) On = Connection to external AC power. 2. Connect the fiber cables to the CETTF10xx-105 media converter as LKF (Link - fiber) On = The fiber link is up. described: Off = A lack of power or a bro
Streszczenie treści zawartej na stronie nr. 4
CETTF10xx-105 Operation -- Continued Cable Specifications The physical characteristics must meet or exceed IEEE 802.3™ specifications. Product Features Fiber Cable AutoCross™ Bit Error Rate: <10-9 When the AutoCross feature is activated, it allows either straight-through Single mode fiber (recommended): 9 µm (MDI) or crossover (MDI-X) copper cables to be used when connecting to Multimode fiber (recommended): 62.5/125 µm 10Base-T devices. AutoCross determines the characteristics of the conn
Streszczenie treści zawartej na stronie nr. 5
CETTF10xx-105 Cable Specifications -- Continued Technical Specifications For use with Transition Networks Model CETTF10xx-105 or equivalent. Copper Cable Standards IEEE 802.3™ Category 3: (minimum requirement) Data Rate 10 Mb/s Gauge 24 to 22 AWG Attenuation 11.5 dB/100m @ 5-10 MHz Dimensions 3.4" x 0.86" x 5.0" (86 x 22 x 127 mm) Maximum Cable Distance 100 meters Weight 3 oz (91 g) (approximate) Category 5: (recommended) Power Consumption 2.3 watts Gauge 24 to 22 AWG Attenuation 22.0 dB /10
Streszczenie treści zawartej na stronie nr. 6
CETTF10xx-105 Troubleshooting Contact Us If the media converter fails, isolate and correct the failure by determining the Technical Support answers to the following questions and then taking the indicated action: Technical support is available 24 hours a day. US and Canada: 1-800-260-1312 1. Is the PWR LED illuminated? International: 00-1-952-941-7600 NO � Is the media converter slide-in-module installed properly in the Transition Now chassis? Chat live via the Web with Transition Networks Techn
Streszczenie treści zawartej na stronie nr. 7
Compliance Information CISPR22/EN55022 Class A + EN55204 CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructi
