Streszczenie treści zawartej na stronie nr. 1
Impact Driver
MODEL 6952
004352
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
Streszczenie treści zawartej na stronie nr. 2
SPECIFICATIONS Model 6952 Machine screw 4 mm - 10 mm (5/32” - 3/8”) Capacities Standard bolt 6 mm - 14 mm (1/4” - 9/16”) High tensile bolt 6 mm - 10 mm (1/4” - 3/8”) No load speed (RPM) 0 - 3,200/min. Impacts per minute 0 - 3,100 Max. fastening torque 120 N.m (89 ft.lbs) Dimensions (L x W x H) 229 mm x 67 mm x 180 mm (9” x 2-5/8” x 7-1/8”) Net weight 1.3 kg (2.9 lbs) • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GE
Streszczenie treści zawartej na stronie nr. 3
still does not fit, contact a qualified elec- 13. Do not overreach. Keep proper footing trician to install a polarized outlet. Do not and balance at all times. Proper footing and change the plug in any way. Double insula- balance enables better control of the tool in unexpected situations. tion eliminates the need for the three wire grounded power cord and grounded power 14. Use safety equipment. Always wear eye supply system. protection. Dust mask, non-skid safety shoes, hard hat, or hearing p
Streszczenie treści zawartej na stronie nr. 4
22. Use only accessories that are recom- tenance performed by unqualified personnel mended by the manufacturer for your could result in a risk of injury. model. Accessories that may be suitable for 24. When servicing a tool, use only identical one tool, may become hazardous when used replacement parts. Follow instructions in on another tool. the Maintenance section of this manual. Use of unauthorized parts or failure to follow SERVICE Maintenance instructions may create a risk of 23. Tool servic
Streszczenie treści zawartej na stronie nr. 5
SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS USD202-2 The followings show the symbols used for tool. V ....................... volts ....................no load speed n ˚ A ....................... amperes ....................Class II Construction Hz ..................... hertz .../min................revolutions or reciprocation per minute ................ alternating current ...........
Streszczenie treści zawartej na stronie nr. 6
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 004353 Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. 1 To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. 1. Switch trigger Release the switch trigger to stop. Electr
Streszczenie treści zawartej na stronie nr. 7
ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 001266 Installing or removing driver bit or socket bit Use only the driver bit or socket bit shown in the figure. Do 12 mm 9 mm not use any other driver bit or socket bit. (15/32”) (3/8”) 001267 To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as it will go. Then release the sleeve to secure the bit. To remove the bit,
Streszczenie treści zawartej na stronie nr. 8
Hold the tool firmly and place the point of the driver bit in the OPERATION screw head. Apply forward pressure to the tool to the extent that the bit will not slip off the screw. Start the tool slowly and then increase the speed gradually. Release the switch trig- ger just as the screw bottoms out. 004356 The proper fastening torque differs depending upon the kind (S) or size of the screw/bolt, the material of the workpiece to be 12 fastened, etc. Refer to the figure for the relation between fas
Streszczenie treści zawartej na stronie nr. 9
MAINTENANCE CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. 001145 Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only iden- tical carbon brushes. 1 1. Limit mark 004357 Use a screwdriver to remove the brush holder caps. Take
Streszczenie treści zawartej na stronie nr. 10
Memo 10
Streszczenie treści zawartej na stronie nr. 11
Memo 11
Streszczenie treści zawartej na stronie nr. 12
Memo 12
Streszczenie treści zawartej na stronie nr. 13
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
Streszczenie treści zawartej na stronie nr. 14
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
Streszczenie treści zawartej na stronie nr. 15
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA FLORIDA MISSOURI PENNSYLVANIA 3707 E. Broadway Rd., Ste. 6 750 East Sample Road 9876 Watson Road 1704 Babcock Blvd. Phoenix, AZ 85040 Pompano Beach, FL 33064 St. Louis, MO 63126-2221 Pittsburgh, PA 15209 (602) 437-2850 (954) 781-6333 (314) 909-9889 (412) 822-7370 CALIFORNIA GEORGIA NEBRASKA PUERTO RICO 41850 Christy St. 4680 River Green Parkway NW 4129 S. 84th St. 200 Guayama St. Fremont, CA 94538-5107 Duluth,
Streszczenie treści zawartej na stronie nr. 16
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
