Streszczenie treści zawartej na stronie nr. 1
B/W DUAL QUAD NETWORK
OBSERVATION SYSTEM
SSC17WEB
User Guide
Streszczenie treści zawartej na stronie nr. 2
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these Instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the
Streszczenie treści zawartej na stronie nr. 3
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. Graphic Symbol Explanation The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated ‘dangerous voltage’ within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to person
Streszczenie treści zawartej na stronie nr. 4
IMPORTANT SAFEGUARDS Caution Power source is indicated on the rear of the set. It contains high-voltage parts. If you remove the cover, it may cause fire or electric shock. Do not remove the cover by yourself. (Control switches are at the front of the monitor.) 1. Read Instructions : All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions : The safety and operating instructions should be retained for future reference. 3. Heed Warnings :
Streszczenie treści zawartej na stronie nr. 5
8. Accessories : Do not place this monitor on an unstable cart, stand, tripod, bracket or table. The monitor may fall causing serious injury to a child or adult and serious damage to the appliance. Use only with a cart, stand, tripod. bracket or table recommended by Samsung or sold with the monitor. Any mounting of the monitor should follow Samsung’s instructions and should use a mounting accessory recommended by Samsung. 9. Ventilation : Slots and openings in the cabinet are provided for ventil
Streszczenie treści zawartej na stronie nr. 6
13. Lightning : For added protection for this monitor during a lightning storm or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the monitor due to lightning and power-line surges. 14. Overloading : Do not overload wall outlets and extension cords as this can result in a risk of fire of electric shock. 15. Object and liquid Entry : Never push objects of any kind into this monitor through
Streszczenie treści zawartej na stronie nr. 7
18. Replacement Parts : When replacement parts are required be sure the service technician has used replacement parts specified by Samsung or have the same characteristics as the original parts. Unauthorized substitutions may result in fire electric shock or other hazards. 19. Safety Check : Upon completion of any service or repairs to this monitor ask the service technician to preform safety checks to determine that the monitor is in proper operating condition. FCC & ICES Information Warning T
Streszczenie treści zawartej na stronie nr. 8
Information to user Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates uses and can radiate
Streszczenie treści zawartej na stronie nr. 9
The party responsible for product compliance: SAMSUNG ELECTRONICS CO., LTD. America QA Lab of Samsung 3351 Michelson Drive, Suite #290, Irvine, CA92612 USA IC Compliance Notice This Class (A) digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe (A) respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numéiqu
Streszczenie treści zawartej na stronie nr. 10
Contents IMPORTANT SAFETY INSTRUCTIONS ...........................Eng-2 IMPORTANT SAFEGUARDS..............................................Eng-4 FCC & ICES Information .......................................................Eng-7 Chapter 1: System Components and Installation 1-1) Environmental requirements for installation and safety ...Eng-12 1-2) System Components......................................................Eng-13 1-3) CAMERA composition and installation method .........Eng-14 1-4) CAME
Streszczenie treści zawartej na stronie nr. 11
Chapter 3: Setting each item function at SETUP MENU 3-1) DATE/TIME MENU Function setting..........................Eng-26 3-2) DWELL TIME MENU function setting .......................Eng-26 3-3) DISPLAY MENU function setting ..............................Eng-27 3-4) TITLE MENU Function setting ....................................Eng-28 3-5) ALARM MENU Function setting.................................Eng-29 3-6) NETWORK SETUP function and setting method........Eng-30 3-7) SSC17WEB basic setting.
Streszczenie treści zawartej na stronie nr. 12
Chapter 1: System Components and Installation 1-1) Environmental requirements for installation and safety This section describes the environmental requirements for safe installation and use. Install the product on a flat table or in a rack. It should be used only when level and should not be used when stood vertically or obliquely. The location in which the main system is installed and the configuration of the wiring room are very important for proper operation of the system. When the produc
Streszczenie treści zawartej na stronie nr. 13
1-2) System Components The system consists of the following: STANDARD VCR CABLE MONITOR CAMERA POWER CODE & SENSOR INSTALLATION MANUAL CAMERA CABLE CONNECTOR CAMERA BRACKET ITEM MODEL DESCRIPTION Q’ty NOTE MONITOR SSC17WEB 17" CRT MONITOR 1 STANDARD CAMERA SSC-12C NORMAL TYPE CAMERA 4 CAMERA BRACKET SBR-110 STAND TYPE BRACKET 4 Tapping Screw 3 CAMERA CABLE MCB-60 6PIN SHIELD CABLE 4 60ft(1ft=0.3048m) INSTALLATION MANUAL - - 1 POWER CORD - - 1 VCR CABLE - - 1 SENSOR CONNECTOR - - 4 • Check whe
Streszczenie treści zawartej na stronie nr. 14
1-3) CAMERA composition and installation method 1) Standard Camera composition (SSC-12C) PIN NUMBER SPEC ! SPEAKER(HOT) @ VIDEO_OUT # GND $ SPEAKER(COLD) % AUDIO_OUT/ALARM_OUT ^ 12V DC a. Lens It has a focal length of 3.8mm and makes it possible for you to observe a relatively wide area. b. Microphone Capable of picking up all sound in the vicinity of the camera location and transmitting to the monitor. c. Camera fitting groove Enables the camera to be fixed onto the bracket. You may install
Streszczenie treści zawartej na stronie nr. 15
f. Speaker It outputs the sound signal which was transferred from the monitor. 2) INSTALLING STANDARD CAMERA (SSC-12C) SSC-12C s camera can be attached to the wall, ceiling or shelf using the camera mount bracket (SBR-110). Choose an installation site that can sufficiently support the weight of the equipments to be installed. Attach the camera mount bracket to the wall or ceiling using the supplied three screws (M4 X L15). Adjust the camera to target the video location and tighten the bracke
Streszczenie treści zawartej na stronie nr. 16
3) CAMERA MOUNT BRACKET(SBR-110) & STANDARD CAMERA(SSC-12C) (1) Overview CAMERA MOUNT BRACKET (SBR-110) is used to attach the camera to a wall, ceiling or shelf. (2) Installation Explains the installation of CAMERA MOUNT BRACKET as wall as the installation of the camera onto the CAMERA MOUNT BRACKET. • Choose an installation site that can sufficiently support the weight of the equipments to be installed. • Attach the camera mount bracket to the wall using the supplied screws (M4 X L15). • Adj
Streszczenie treści zawartej na stronie nr. 17
• Loosen the handle by turning it in a counter clockwise direction and then adjust the camera position . Tighten the handle, turning it clockwise, and lock the camera in position. • Connect the camera cable to the camera. Handle (3) Specifications Use : Indoor Installation : Wall or Ceiling Dimensions : 57 (W) X 47.2(H) X 100.5(L) Weight : 150g Operating Temperature : -10°C ~ 50°C (4) Accessories SCREW (M4 X L15) : 3 pcs Eng-17
Streszczenie treści zawartej na stronie nr. 18
1-4) CAMERA Composition and Connecting Method to MONITOR After positioning monitor and installing four cameras to a desired location, please connect CAMERA to MONITOR through CAMERA CABLE (MCB-60) as shown in the below figure. Please check whether or not it is properly connected. Connection status checking method : • Turn on the monitor after connecting cameras, and check if camera image is displayed. The initial screen mode of monitor is quad mode. • In case monitor and camera is not connecte
Streszczenie treści zawartej na stronie nr. 19
1-5) External terminal connecting method for CAMERA and MONITOR 1) External terminal connecting method for CAMERA • An additional PIR sensor or external sensor can also be connected. • The additional PIR sensor can be connected as shown in the above graphic. • Sensor’s trigger signal is NO (Normal Open). • Sensor is not supplied. (Sold separately) 2) VIDEO OUT BNC (1~4) terminals connecting method of monitor rear VIDEO OUT BNC1 ~ BNC4 terminals in the rear of the monitor are VIDEO terminals
Streszczenie treści zawartej na stronie nr. 20
f) Not Used g) Connect the A/O (HOT) terminal on the rear panel to the Alarm IN terminal of the VCR. h) Connect the A/O (COLD) terminal on the rear panel to the Ground terminal of the VCR. i) Connect the A/R terminal on the rear panel to the Alarm Reset terminal of the VCR. j) Connect the G (ground) terminal on the rear panel to the Ground terminal of the VCR. 1-6) Whole System connection and configuration OR VCR SLAVE MONITOR VCR (TIME LAPSE) REAR Eng-20
