Instrukcja obsługi SECO-LARM USA Enforcer E-37EV

Streszczenie treści zawartej na stronie nr. 1

E-37EV

Alarm Pager System

Manual
 Monitors up to three zones per  Code-learning receiver learns
premises or vehicle, plus up to three transmitter codes.
manual paging.  Transmitter can page an
 One positive and two negative unlimited number of receivers.
instant trigger inputs.
 Colored LEDs or vibrate
 Low-battery indicator. function indicate received page.
 Red LED transmission indicator.  Unattended page indicator.
NOTE: Antenna required. See page 3 for more de

Streszczenie treści zawartej na stronie nr. 2

ENFORCER E-37EV Alarm Pager System Table of Contents Introduction ......................................................................................................................... 2 Parts List ............................................................................................................................. 2 Dimensions ........................................................................................................................ 2 Specifications ..........

Streszczenie treści zawartej na stronie nr. 3

ENFORCER E-37EV Alarm Pager System Specifications Number of codes Over 2 million (factory pre-set) Power 12VDC RF output power 4W max. Standby 10mA Current drain Active 1A Frequency 27MHz Antenna impedance 50 Ω 1 1 Range Up to /2 mile in open air 1 1 5 Dimensions 4 / ”x3 / ”x1 / ” (105x79x33 mm) 8 8 16 Weight 5.1-oz (145g) 1 Actual range may vary depending on the environment, installation, and/or antenna. Number of codes Learns up to 3 transmitter codes 2 Power 3VDC (2 AAA

Streszczenie treści zawartej na stronie nr. 4

ENFORCER E-37EV Alarm Pager System TYPE 2: CB antenna (A Position) 1. Connect the male antenna plug of an optional CB antenna into the transmitter jack marked “ANT.” 2. Place the antenna selection switch in the “A” position. TYPE 3: Standard radio antenna (B Position) 1. Disconnect the radio antenna lead going into the radio and connect it to the transmitter jack marked “ANT.” 2. Connect the provided male-to-male 18” radio antenna adapter cord between the transmitter jack marked “RAD

Streszczenie treści zawartej na stronie nr. 5

ENFORCER E-37EV Alarm Pager System Connection Diagram E-37ANT (Optional) Antenna Selection Antenna Switch Antenna (“ANT”) LED Manual Page Radio Radio (“RADIO”) Diode Cut IN4004 White (Short): Radio Switched Power Lead White (Long): Power Antenna Fuse (2A) +12 VDC Red: Constant +12V to Fuse Box Black: Ground Purple: Positive (+) Trigger Ground Blue: Second Negative (-) Trigger Green: First Negative (-) Trigger Programming The receiver must learn the transmitte

Streszczenie treści zawartej na stronie nr. 6

ENFORCER E-37EV Alarm Pager System Audible and Visual Signals Chart Receiver Display Transmitter Input Audible / Vibrator ID Page LED Zone LED Indicator Positive Trigger Green Green Groups of 9 Negative Trigger #1 Green Red Groups of 9 Green Negative Trigger #2 Green Orange Groups of 9 Manual Page Green Green 3 groups of 3 Power ON Green None 3 groups of 3 Positive Trigger Red Green Groups of 9 Negative Trigger #1 Red Red Groups of 9 Red Negative Trigger #2 Red Orange

Streszczenie treści zawartej na stronie nr. 7

ENFORCER E-37EV Alarm Pager System Alarm Paging  When triggered by either the purple (+), green (-), or blue (-) triggers, the receiver will beep (or vibrate) continuously for 1 minute in groups of 9.  The Page LED will indicate which transmitter is sending the signal (Green, Red, or Orange).  The Zone LED will indicate which trigger was triggered. - Positive trigger (purple wire) will flash green. - Negative trigger #1 (green wire) will flash red. - Negative trigger #2 (blue wir

Streszczenie treści zawartej na stronie nr. 8

ENFORCER E-37EV Alarm Pager System Troubleshooting No page signal  Check that all connections are securely made  Check that the antenna is securely fastened  Check the receiver batteries  Possibly out of range – Move antenna to better position  Make sure the antenna selection switch is in the correct position  Check that the transmitter has been properly learned Receiver only outputting vibrate/beep  Check that the receiver is in the correct alert mode Also A