Streszczenie treści zawartej na stronie nr. 1
Model APS-786
Owner's Manual
4 Button Remote Start Security System With
Plug-In Shock Sensor & Starter Disable
FEATURES:
2 Four Button Programmable RF Transmitters
Four Channel Code Learning Receiver (capable of accepting 4 transmitters)
Code Hopping Technology
Selectable Manual Override Mode
Remote Panic in all modes
Protected Valet/Override
Remote Start Safety Control Switch
Selectable Automatic Timed Start Mode
User Programmable Manual Override Code
7 Function LED - Arm /
Streszczenie treści zawartej na stronie nr. 2
Your Remote Start Alarm System has many features and available options some of which are selected at time of installation. For your reference, the list on page 9 of this manual shows what features and options have been installed. Consult your installing dealer for options that may have been installed and are not listed. YOUR “ CODE HOPPING “ TRANSMITTERS: The transmitters included with your new remote start system use the most advanced and secure form of radio frequency transmission available o
Streszczenie treści zawartej na stronie nr. 3
1. Turn the engine off, exit the vehicle, and close all doors, hood and trunk. The dash mounted LED will begin to flash rapidly indicating that the 30 second passive arming timer has begun. If the LED does not begin to flash rapidly, then you have left a door, hood, or trunk ajar. Closing this entry point will allow the arming cycle will begin. If any entry point is opened during the 30 second arming cycle, arming will be suspended. When all entry points are closed, the arming cycle will begin
Streszczenie treści zawartej na stronie nr. 4
second time will cause all doors to unlock. If your transmitter has a sperate lock unlock buttons, pressing the unlock button anytime after the first unlock command will cause all the vehicle doors to unlock. SILENT DISARMING 1. As you approach the vehicle, press and hold the disarm button of your key chain transmitter for two seconds. The parking lights will flash twice, and the dash mounted LED will turn off confirming that the system is disarmed. The siren will not chirp. If you have the opt
Streszczenie treści zawartej na stronie nr. 5
1. Enter the vehicle, and turn the ignition key to the on position. 2. Press and hold the valet pushbutton switch until the dash mounted LED turns on solid. The system will remain in the valet mode. 3. To return to normal operation, press and release the pushbutton switch any time the ignition is on. NOTE: Always remember to return the vehicle to the valet off position. This will ensure that the vehicle remains protected at all times. MANUALLY OVERRIDING YOUR SYSTEM: USING THE VALET SWITCH MANUA
Streszczenie treści zawartej na stronie nr. 6
Custom Code Programming Example: To Change the code from the factory pre-assigned code of 11 to “52” you would do the following: 1. Disarm the system by use of the transmitter, or by use of the emergency override sequence. 2. Turn the ignition switch to the on position. 3. Within 10 seconds, press and release the valet/override switch, 3 times. 4. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will flash one time.) 5. Within 10 s
Streszczenie treści zawartej na stronie nr. 7
NOTE: If the vehicle battery is disconnected then reconnected, the unit will return to the default setting of chirps on. Repeat the above procedure to eliminate the arm/disarm chirps. REMOTE PANIC OPERATION The Lock or Unlock button on your keychain transmitter also functions as a panic switch for use in emergency situations. To use remote panic, 1. Press and hold the Lock or Unlock button on the keychain transmitter for 3 or more seconds. The alarm will immediately sound. 2. To stop the alarm,
Streszczenie treści zawartej na stronie nr. 8
When you arrive at your vehicle, disarm the alarm system by pressing and releasing the Disarm button of your keychain transmitter. Enter the vehicle and turn the ignition key to the on position. CAUTION ! Do not turn the key to the start position. This will cause the starter motor to engage with the already running engine which could result in damage. Step on the brake pedal to disengage the remote start unit. The vehicle will continue to run but now on it's own power. NOTE: The engine will st
Streszczenie treści zawartej na stronie nr. 9
Remote Window Close Remote Garage Door Interface To operate the accessory associated with channel 3, press and hold the trunk/key button(s) of your keychain transmitter for four seconds. NOTE: The feature that has been added to channel 3 will always be operated using the same transmitter button that controls the remote start unit. There is no way to move the channel 3 function to a different channel. ADDITIONAL REMOTE FUNCTION CHANNEL 4 The system has an additional feature, (Channel 4) ,tha
Streszczenie treści zawartej na stronie nr. 10
APS-786 SYSTEM FUNCTIONS AT A GLANCE ALARM DASH LED INDICATORS RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = VALET MODE 3 FLASH... PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1 ALARM SIREN CHIRP INDICATION 1 CHIRP* = ARM 2 CHIRPS* = DISARMED 3 CHIRPS = ARMING WITH ENTRY POINT OPENED 4 CHIRPS = DISARM AFTER INTRUSION 5 CONTINUOUS = TRIGGERED/PANIC ALARM PARKING LAMP INDICATIONS 1 FLASH = ARM 2 FLASH = DISARM 3 FLAS
