Streszczenie treści zawartej na stronie nr. 1
Quick start guide
TL7612
DECT 6.0 cordless headset
and handset lifter
Streszczenie treści zawartej na stronie nr. 2
Installation You must install and See pages 10-11 charge the battery before for instructions. STOP! using the headset. If you subscribe to high-speed Internet service (DSL - digital subscriber line) through your telephone line, you must install a DSL filter between the telephone line cord and the telephone wall jack. The filter prevents noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters. For customer se
Streszczenie treści zawartej na stronie nr. 3
Quick reference guide - headset ON/OFF Press to make and/or answer a call, and to end a call. Headset indicator lights ON/OFF light status On • Headset is charging in the headset base. • Headset is trying to register to the headset base. • Headset is searching for the headset base. Flashing • Flashes slowly when an incorrect type of battery is installed. • Flashes three times, followed by a pause, then repeats this cycle three more times and then shuts down to indicate the battery is very l
Streszczenie treści zawartej na stronie nr. 4
Quick reference guide - headset VOLUME / - + Press the volume keys on the side of the headset to adjust the listening volume when on a call. MUTE/FLASH Press to mute the microphone during a call. Press and hold to answer a call waiting call while on a call. Earpiece Press to mute the ring tone in the earpiece when there is an incoming call. Microphone Battery cover Open to install or replace the battery.
Streszczenie treści zawartej na stronie nr. 5
Quick reference guide - headset Headset alert tones Three quick beeps • VOLUME /+ - keys are pressed when the volume is already at its highest or lowest setting. • The headset is not registered and the headset ON/OFF button was pressed. • The headset is out of range from the headset base during a call. One short beep Low battery warning. every 0 seconds One short beep The call is muted. every 5 seconds One long beep Call waiting alert tone. (repeated) One short beep The headset ON/OFF k
Streszczenie treści zawartej na stronie nr. 6
Quick reference guide - headset base Charging cradle Insert the headset here for charging. PAIR Press to register or deregister the headset. NO LIFTER MODE light On when NO LIFTER MODE is selected. Flashes while on a call, or another telephone is in use on the same line. Flashes quickly when there is an incoming call. LIFTER MODE light On when LIFTER MODE is selected. Flashes while on a call. Flashes quickly when there is an incoming call. MUTE light On when a call is muted.
Streszczenie treści zawartej na stronie nr. 7
Quick reference guide - headset base LIFTER AUDIO ADJUST Switch to choose the best headset audio quality when using LIFTER MODE. VOLUME / Press the volume keys on the side of the headset base to adjust the speaking volume while on a call. MODE Press to choose between NO LIFTER MODE or LIFTER MODE when the headset is not in use. The corresponding light turns on. 5
Streszczenie treści zawartej na stronie nr. 8
Quick reference guide - headset base Headset base indicator lights NO LIFTER MODE LIFTER MODE MUTE NO LIFTER MODE • On when NO LIFTER MODE is selected (default mode). • Flashes quickly when there is an incoming call. • Flashes when the headset is in use or another telephone on the same line is in use. LIFTER MODE • On when LIFTER MODE is selected. • Flashes quickl quickly y when ther when there e is an is an incoming call. • Flashes when the headset is in use. MUTE • On when a call is mute
Streszczenie treści zawartej na stronie nr. 9
Quick reference guide - handset lifter SENSOR ADJ knob Adjusts the sensitivity of the ring detector. ADJUST LIFTER knob Adjusts the height of the lifter arm. Lifter arm Holds the corded telephone handset. Switch hook presser When the CORDED HANDSET CONNECTED switch is set to YES, pressing ON/OFF on the headset raises or lowers the switch hook presser. RING DETECT jack Lifter control cable Plug in the auxiliary ring This cable is hard wired into the lifter detector. and plugs into the LIFTER
Streszczenie treści zawartej na stronie nr. 10
Quick reference guide - handset lifter RING ON/OFF Press to turn the ring detector on or off. When the ring detector is off, the cordless headset does not ring. Switch hook presser adjustment knob Adjusts the position of the switch hook presser. Small lifter pad Holds the earpiece of the corded telephone handset. STATUS light On in red when the ring detector is off. On in blue when the ring detector is on and the headset not in use. Flashes blue four times every three seconds when the rin
Streszczenie treści zawartej na stronie nr. 11
Quick reference guide - handset lifter STATUS light Red • On when the headset is not in use and the ring detector is turned off. • Flashes slowly when the headset is in use and the ring detector is turned off. Blue • On when the headset is not in use and the ring detector is turned on. • Flashes four times every three seconds when the ring detector detects an incoming call. • Flashes slowly when the headset is in use and the ring detector is turned on. Off • The headset base does not h
Streszczenie treści zawartej na stronie nr. 12
Battery installation Install the battery as shown below. After installing the battery, you may be able to make and receive short calls. For optimal performance, charge the headset battery for at least six hours before use. When the headset is not in use, recharge the headset by returning it to the headset base. 1 . If the battery compartment cover is attached, press on both sides of the cover and lift it up and off. . Insert the battery into the battery compartment with the label THIS
Streszczenie treści zawartej na stronie nr. 13
Battery charging After installing the battery, charge the headset by placing it on the headset base as shown below. The headset ON/OFF light is on when the headset is charging. Push ON/OFF light Insert . Insert the headset into . Push the headset downward the charging cradle. until the ON/OFF light on the headset turns on. CAUTION: There may be a risk of detonation if you use a wrong type of battery. Use only the supplied rechargeable battery or replacement battery (model BT55 “BYD
Streszczenie treści zawartej na stronie nr. 14
Headset base and lifter installation Installation preparation Before installing the headset base, remove the rear bottom piece of the headset base by pushing it away from the base (as shown in Figure ). Figure Install the headset base as shown on the following pages. After completing installation option , or (see page 5 ), slide the rear bottom piece towards the headset base until it clicks into place (as shown in Figure ). Figure
Streszczenie treści zawartej na stronie nr. 15
Headset base and handset lifter installation No lifter mode or lifter mode There are two answer modes available on the headset base. The current mode is indicated by the NO LIFTER MODE or LIFTER MODE lights on the front of the headset base. • When plugging your headset base into the telephone wall jack, make sure the headset base mode is set to NO LIFTER MODE. MODE -OR- • When connecting your headset base to a corded telephone, make sure the headset base mode is set to LIFTER MODE and t
Streszczenie treści zawartej na stronie nr. 16
Headset base and handset lifter installation Cord labels The cords provided with your headset have colored labels attached to help you plug them into the headset base. The back of the headset base has colored dots above the jacks, and the names of the jacks on the rear bottom piece of the headset base corresponding to the colored labels on the cords. If you are using installation option , you can attach the provided light blue colored label to the end of the curly handset cord of your tel
Streszczenie treści zawartej na stronie nr. 17
Headset base and handset lifter installation Installation options You have three installation options: Option 1: Connect the handset lifter to a corded phone (pages - ). This option enables you to answer calls even if you are away from the telephone base. For this option, you can use the headset with a single line or multiple line corded telephone (such as the AT&T 0 0, 0 0 or 0 0) or a digital business system (such as a proprietary PBX telephone system). The handset lifter (
Streszczenie treści zawartej na stronie nr. 18
Headset base and handset lifter installation Option 1: Connect the handset lifter to a corded phone . Unplug the curly handset cord from the telephone and plug it into the CURLY CORD jack (light blue dot) on the headset base. . Plug one end of the telephone line cord (provided with the headset base) into the base handset jack on the telephone where the curly handset cord was originally plugged in. . Plug the other end of the line cord into the BASE JACK (orange dot) on the headset ba
Streszczenie treści zawartej na stronie nr. 19
Headset base and handset lifter installation Adjust the corded handset audio . Make sure that LIFTER MODE light on the headset base is on. Press the MODE button on the headset base to change the mode. . Lift the corded handset to release the switch hook. Place the corded handset aside. . Place the headset earpiece in your ear. . Press ON/OFF on the headset to listen for a dial tone. If there is no dial tone or the dial tone is unclear, slide the LIFTER AUDIO ADJUST switch on the si
Streszczenie treści zawartej na stronie nr. 20
Headset base and handset lifter installation Attach the lifter . To choose where to install the lifter on your telephone, look at the space underneath the corded handset. If there is a speaker, the lifter should be centered over the speaker. If there is no speaker, the lifter should be centered within the space. Make sure the lifter arm is raised above the switch hook of the telephone base. . Peel off the protective strips from the adhesive tape at the bottom of the lifter. . Carefu
