Streszczenie treści zawartej na stronie nr. 1
OPERATION MANUAL
Streszczenie treści zawartej na stronie nr. 2
1 1 Introduction 2 1.1 Part specification 2 2 Installation 3 2.1 Installing the instrument 4 2.2 Electrical installation 4 3 Function overview 5 3.1 How to use the push buttons 5 3.2 Position 6 3.2.1 Time and date 6 3.2.2 Battery voltage 6 3.3 Navigation functions 7 3.3.1 Cross track error (XTE) 7 3.3.2 Waypoint closure velocity (WCV) . 7 3.3.3 Time To Go (TTG) 7 3.3.4 Select Waypoint 8 3.3.5 Man Over Board (MOB) 8 3.3.6 View the MOB position 8 3.3.7 Top arrows 9 4 NMEA input 9 5 Calibration
Streszczenie treści zawartej na stronie nr. 3
1 Introduction Thank you for choosing the Star NAV Repeater which will display all necessary data from your NMEA navigator. Power and NMEA data are connected on the reverse side of the instrument. The colour coded 4-pole jack plug makes the installation easy. Part specification Star SEA Data is delivered with all mounting material. Make sure all these parts are in the package. QTY ITEM QTY ITEM 1 Instruction manual for use 1 Drill template 1 W 4 Mounting screws 1 Instrument SEA Data 4 Rubber
Streszczenie treści zawartej na stronie nr. 4
3 2 Installation • The installation includes 6 major steps: Read the installation and operation manual. Plan where to install the transducer and instrument. Install the transducer, then the instrument. Run the cables. Take a break and admire your installation. Learn the functions and calibrate your instrument. • Before you begin drilling... think about how you can make the installation as neat and simple as your boat will allow. Plan where to position the instrument. Think about leaving
Streszczenie treści zawartej na stronie nr. 5
Installing the instrument • Place the adhesive drill template on the desired location for the instrument. 7 1 Drill the four screw holes using a 2 .8 mm ( / ”) drill for wood or 3.2 mm ( / ”) 64 8 1 for fibre glass. Use a 52 mm (2 / ”) hole saw to machine the clearance 16 hole for the instrument connection socket. Note! Never drill through the instrument’s four mounting holes as the gasket may be damaged and thus cause leakage. The warranty is not valid for damage caused by drilling through t
Streszczenie treści zawartej na stronie nr. 6
3 Function overview The display is divided in two function groups: Position and Navigation. To change between them, press MODE . To scroll in function list, press UP or DOWN . How to use the push buttons Mode / Light button This button is used to change between Position mode and Navigation mode. One short press changes between the two modes. To select light levels, press mode for more than two Down button This button is used to move down in the function list or to decrease a value in set mode
Streszczenie treści zawartej na stronie nr. 7
The position is displayed in latitude and longitude to three decimal places. If the NMEA Navigator just sends two decimals, the third will always read zero. Time and date To display date and time, press DOWN . Date and time is displayed in month, day, hour, minute and second. Some NMEA navigators does not send date. In that case, the text TIME is written instead of the date. To set the local time zone, press KEY . The ”underline” sign is flashing ( underline is the same as plus), change wit
Streszczenie treści zawartej na stronie nr. 8
Navigation functions To change to combi steer, press MODE . The combi steer window provides you with information of five values at a time. The arrow at the top helps you to keep on track. This function is explained in section 3.3.7. The functions displayed are speed over ground, course over ground, distance to Waypoint and course to Waypoint. If no W aypoint is selected to navigate towards in the NMEA navigator, the bottom row will display dashes. Cross track error (XTE) To display XTE, pres
Streszczenie treści zawartej na stronie nr. 9
Select Waypoint In the navigation mode you can at any time set a Waypoint to go to. The NAV Repeater will then compute the distance and bearing to Waypoint and all other functions .The W aypoint is selected by pressing the KEY in any navigation mode. When the KEY is pressed the NMEA W aypoint number is displayed. To enter your Waypoint, press or DOWN , the text Lat/Lon is displayed. Press KEY and the present position is displyed, edit the latitudecoordinate for your Waypoint. To increase/decr
Streszczenie treści zawartej na stronie nr. 10
Top arrows At the top of the display there are four arrows and four text signs. The arrows tell you if you are on the ”road” or not and the text displays the status of your NMEA navigator . You are on the the road, on the left side right side of the road, on the left side of the road the road the right side navigator is in navigator is navigator is in in aqusition differential mode mode mode The width of the road can be adjusted, see calibration section 5.9. If you select the road to be 0.050
Streszczenie treści zawartej na stronie nr. 11
The following NMEA sentences are red for displaying different data. The sentences are in priority order (i.e. if the NMEA navigater is sending more than one sentence, the information in the first sentence is displayed.) Position: 1. GGA, 2. RMC, 3. RMA, 4.GLL Date and time: 1. ZDA, 2.RMC, 3.GGA, 4.GLL, 5. BWC, 6.BWR Speed Over Ground: 1. RMC , 2. RMA, 3. VTG Course Over Ground: 1. RMC, 2. RMA, 3. VTG Bearing To Waypoint: 1. BWC, 2. RMB, 3. BWR Distance To Waypoint: 1. BWC, 2. RMB, 3. BWR Time
Streszczenie treści zawartej na stronie nr. 12
Unit for distance The unit for distance can be selected as nautical miles (NM), kilometres (KM) or miles (MI). Unit for speed The unit for speed can be selected as knots (KTS), kilometres/hour (KMH) or miles/hour (MPH). Seconds ON/OFF Select the position to be displayed in seconds or hundreths of minutes. If seconds is set to OFF, hundreths of minutes is displayed. Magnetic bearing ON/OFF Select the bearing to display magnetic or true bearing. If magnetic bearing is set to ON, all bearings
Streszczenie treści zawartej na stronie nr. 13
Circle alarm The Star NAV Repeater has a built in arrival alarm. When the boat is closer to Waypoint than the setting in this calibration mode, the alarm is activated. You can select the radius of the circle. To turn off the alarm, set the value to Circle alarm limit is always in nautical miles. Cross track error alarm The Star NAV Repeater has a built in cross track error (XTE) alarm. When the boats XTE is more than the setting in this calibration mode, the alarm is activated. You can se
Streszczenie treści zawartej na stronie nr. 14
h 6 Fault finding The instrument has three fault messages. No INPUT, NO DATA and UNKNOWN dATA. No power supply 1. Check fuse. 2. Check connections. No signals are 1. Check connections registrated by the NAV 2. Check if your NMEA navigator is sending Signals are recived but 1.Check connections non recognisable by 2.Change polarity of the NAV Repeater. NMEA out A and B 3.Check baudrate Wrong type of NMEA 1.Check the manual for NMEA output data settings. WARRANTY All our products are desi
Streszczenie treści zawartej na stronie nr. 15
The warranty covers repair of defective parts, due to faulty manufacture and includes labour when repaired in the country of purchase. The warranty period is two years, and commences from the date of purchase. The above warranty is the Manufacturers only warranty and no other terms, expressed or implied, will apply. The Manufacturer specifically excludes the implied warranty of merchantability and fitness for a particular purpose. • The supplied warranty card and receipt with proof of purchase
