Streszczenie treści zawartej na stronie nr. 1
PRODUCT GUIDE
MODEL 463741510
IMPORTANT: Fill out the product record information below.
Serial Number
See rating label on grill for serial number.
Date Purchased
For support and to register your
grill, please visit us at
www.charbroil.com
If you have questions or need
assistance during assembly,
please call 1-800-241-7548.
Estimated assembly time: 45 minutes
The following are trademarks registered by W.C. Bradley Co. in the U.S. Patent and Trademark Office: Caldera®; Charcoal2Go®; Char-Broil
Streszczenie treści zawartej na stronie nr. 2
TABLE OF CONTENTS DANGER For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 If you smell gas: Grilling Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-13 1. Shut off gas to the appliance. Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2. Extinguish any open flame. 3. Open lid. Parts List. .
Streszczenie treści zawartej na stronie nr. 3
WARNING CAUTION CALIFORNIA PROPOSITION 65 Using pots larger than 6 quarts in capacity could 1. Combustion by-products produced when using exceed weight limit of the this product contain chemicals known to the State of side burner shelf or side shelf, California to cause cancer, birth defects, and other reproductive harm. resulting in failure 2. This product contains chemicals, including lead of grill cart components. and lead compounds, known to the State of California to cause cancer, birth
Streszczenie treści zawartej na stronie nr. 4
GRILLING GUIDE – Getting Started Temperature The temperature gauge in the hood of your new grill measures air temperature. The air temperature inside your grill will never First Time Use be as hot as the temperature at the cooking surface. Read your Assembly Manual and ensure the grill is put together properly. Remove all Point-of-Purchase advertising material from Note: Since 1995, all regulators (the part that attaches to the gas all grill surfaces before first use. We recommend oper
Streszczenie treści zawartej na stronie nr. 5
Rotisserie Cooking GRILLING GUIDE – Grilling 101 Rotisserie cooking is best for 'round' meat, such as large roasts, whole poultry, and pork. It generally requires an accessory motor Outdoor grilling is really quite simple. You'll succeed with and spit rod that allows the meat to be turned at a constant burgers, dogs, or steaks usually on your very first try. With speed. Rotisserie cooking is best done in front of a special experience, you will learn how to work with your grill, creati
Streszczenie treści zawartej na stronie nr. 6
Wood Chips GRILLING GUIDE – Tips & Tricks For extra smoke flavor when grilling, try adding wood chips. Cooking on your new grill is a hands-on experience, and it is Soak the chips in water for approximately 30 minutes before recommended to remain outside with your grill while cooking. adding to a smoke box or pan. Place smoke box or pan on top of Grilling can be affected by many external conditions. In cold the cooking grate above the flame. Turn grill on high until the weather, you wi
Streszczenie treści zawartej na stronie nr. 7
Cooking surfaces: If a bristle brush is used to clean any of the GRILLING GUIDE – Cleaning Your Grill grill cooking surfaces, ensure no loose bristles remain on cooking Why Clean? surfaces prior to grilling. It is not recommended to clean cooking We've all heard the saying, 'an ounce of prevention is worth a surfaces while grill is hot. pound of cure.’ This is great advice when it comes to keeping your grill clean. Storing Your Grill • Clean cooking grates. Routine Care • Store grill in dr
Streszczenie treści zawartej na stronie nr. 8
LP Cylinder USE AND CARE •The LP cylinder used with your grill must meet the following requirements: •Use LP cylinders only with these required measurements: 12" DANGER (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) capacity maximum. • NEVER store a spare LP cylinder under or near •LP cylinders must be constructed and marked in accordance the appliance or in an enclosed area. with specifications for LP cylinders of the U.S. Department of Transportation (DOT) or for Cana
Streszczenie treści zawartej na stronie nr. 9
e s i w k LP Cylinder Exchange Connecting Regulator to the LP Cylinder •Many retailers that sell grills offer you the option of replacing 1.LP cylinder must be properly secured onto grill. (Refer to your empty LP cylinder through an exchange service. Use only assembly section.) those reputable exchange companies that inspect, precision fill, 2.Turn all control knobs to the OFF position. test and certify their cylinders. Exchange your cylinder only for an OPD safety feature-equipped cylinder
Streszczenie treści zawartej na stronie nr. 10
Straight Leak Testing Valves, Hose and Regulator 1.Turn all grill control knobs to OFF. 2.Be sure regulator is tightly connected to LP cylinder. 3.Completely open LP cylinder valve by turning hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately. There is a major leak at the connection. Correct before proceeding. 4.Brush soapy solution onto areas circled below, or other similar Hold coupling nut and regulator fittings on your grill. as shown for proper connection
Streszczenie treści zawartej na stronie nr. 11
Safety Tips WARNING s Before opening LP cylinder valve, check the coupling nut for tightness. For Safe Use Of Your Grill And To Avoid Serious s When grill is not in use, turn off all control knobs and LP Injury: cylinder valve. •Do not let children operate or play near grill. s If the outdoor cooking gas appliance is not in use, the gas must be turned off at the supply cylinder. Storage of an •Keep grill area clear and free from materials that burn. outdoor cooking gas appliance indoors is
Streszczenie treści zawartej na stronie nr. 12
Ignitor Lighting Sideburner Match Lighting ? Do not lean over grill while lighting. 1. Turn ON gas at LP cylinder. 2. Hold lit match to any port on the burner. Push in and turn 1. Turn OFF gas burner control valves. 2. Turn ON gas at LP cylinder. sideburner knob to the HI position. Be sure burner lights 3. Open lid during lighting. and stays lit. 4. To ignite, turn left knob to the PRE-HEAT position. Burner Flame Check 5. Push IGNITOR button rapidly. • Remove cooking grates and flametamers
Streszczenie treści zawartej na stronie nr. 13
• Plated wire grates: Wash grates with concentrated grill Cleaning the Burner Assembly cleaner or use soap and water solution. Dry thoroughly and Follow these instructions to clean and/or replace parts of burner store indoors between cookouts. assembly or if you have trouble igniting grill. • Stainless steel surfaces: To maintain your grill’s high quality 1. Turn gas OFF at control knobs and LP cylinder. appearance, wash with mild detergent and warm soapy water 2. Remove cooking grate and h
Streszczenie treści zawartej na stronie nr. 14
LIMITED WARRANTY This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of purchase*. The manufacturer reserves the right to require that defective parts be returned, postage and or freight pre-paid by the consumer for re
Streszczenie treści zawartej na stronie nr. 15
PARTS LIST Key Qty. Description Key Qty. Description A 1 FIREBOX HH 2 KNOB B 2 SUPPORT, F/ HEAT TENT II 1 GENERATOR C 2 SUPPORT BAR, F/ COOKING GRATE JJ 1 SIDEBURNER SHELF D 1 BURNER KK 1 SIDEBURNER DRIP PAN E 1 ELECTRODE/COLLECTOR BOX LL 1 SIDEBURNER F 1 VALVE/HOSE/REGULATOR ASSEMBLY MM 1 SIDEBURNER LID G 1 CONTROL PANEL NN 1 ELECTRODE F/ SIDEBURNER H 1 SIDE SHELF OO 1 CONTROL KNOB, F/ SIDEBURNER I 1 SHELF GRIP PP 1 SIDEBURNER GRATE J 2 WHEEL QQ 1 HEAT SHIELD UFC K 2 AXLE BOLT RR 2 RETAINER CLI
Streszczenie treści zawartej na stronie nr. 16
PARTS DIAGRAM V DD W AA X QQ Z C D EE GG I Y B E C FF A PP H MM B JJ RR G LL KK N NN L BB N U II HH OO F SS T CC L U N M O P S R K Q J 16
Streszczenie treści zawartej na stronie nr. 17
ASSEMBLY Left leg 1 □ Place the leg shelf support with match holder onto leg as shown. Attach another leg support to other leg with no leg extender. Attach each side with #10-24x1-3/4" machine screw and #10-24 wing nut (A). □ Attach one support bar to the upper part of legs with #10-24x1-3/4" machine screws and #10-24 wing nuts (B). NOTE: Do not tighten screws until Step 5. Leg Shelf Support Support Bar A A #10-24x1-3/4’’ Machine Screw #10-24 Wing Nut #10-24x1-3/4’’ B #10-24x1-3/4’’ Mac
Streszczenie treści zawartej na stronie nr. 18
Place support bar between right legs, and place two rails on outside of leg. Attach with #10-24x1-3/4" machine screws and 3 #10-24 wing nuts. On left leg attach rail as shown. Right leg #10-24x1-3/4’’ Place rail with Machine Screw rating label to back Qty.8 Support Bar Rail #10-24 Wing Nut Qty.8 Turn assembly upside-down. Insert axle bolts into wheels. Facing the back, position tank support bracket between left legs. 4 Insert 5/16’’ axle bolt through leg and bracket and secure with hitch pin.
Streszczenie treści zawartej na stronie nr. 19
Front Panel 5 □ Place front panel with holes side on top, attach to front of cart with #10-24x1/2" machine screws in lower holes and with push fasteners in upper holes (A). □ You will need to remove the wing nuts and screws installed in step 1A to attach another front panel. And use push fasteners to attach the front panel on the lower holes (B). Tighten all screws from previous steps. B A #10-24x1/2’’ Push Fastener Machine Screw Qty.4 Qty.2 Tank Exclusion 6 Hook the tank exclusion wires o
Streszczenie treści zawartej na stronie nr. 20
Control Panel 7 Attach control panel to cart with #10-24x1-3/4" machine screws and #10-24 wing nuts. Control panel #10-24x1-3/4’’ Machine Screw Qty.2 #10-24 Wing Nut #10-24x1-3/4’’ Machine Screw #10-24 Wing Nut Qty.2 Valve/Hose/Regulator and Ignitor 8 Place valve/hose/regulator onto control panel. Attach with two #10-24x1/2" machine screws. (Note: Make sure the two valve stems are leveled; otherwise, this can cause main burner level problems.) Attach ignitor to control panel using the stamp
