Streszczenie treści zawartej na stronie nr. 1
The Chamberlain Group, Inc.
845 Larch Avenue
Elmhurst, Illinois 60126-1196
www.chamberlain.com
®
GARAGE DOOR OPENER
Models PD752D 3/4 HP
PD752KLD 3/4 HP
For Residential Use Only
Owner’s Manual
■ Please read this manual and the enclosed safety materials carefully!
■ Fasten the manual near the garage door after installation.
®
■ The door WILL NOT CLOSE unless The Protector System is connected
and properly aligned.
■ Periodic checks of the opener are required to ensure safe operation.
■ The model
Streszczenie treści zawartej na stronie nr. 2
TABLE OF CONTENTS Introduction 2-7 Adjustment 27-29 Safety symbol and signal word review........................2 Adjust the travel limits ...............................................27 Preparing your garage door ........................................3 Adjust the force .........................................................28 Tools needed...............................................................3 Test the safety reversal system.................................29 ® Planning ..........
Streszczenie treści zawartej na stronie nr. 3
1 Preparing your garage door WARNING WARNING Before you begin: To prevent possible SERIOUS INJURY or DEATH: • Disable locks. • ALWAYS call a trained door systems technician if CAUTION WARNING • Remove any ropes connected to garage door. garage door binds, sticks, or is out of balance. An unbalanced garage door may not reverse when • Complete the following test to make sure your required. garage door is balanced and is not sticking or binding: • NEVER try to loosen, move or adjust garage door, d
Streszczenie treści zawartej na stronie nr. 4
Planning Identify the type and height of your garage door. • Do you have an access door in addition to the Survey your garage area to see if any of the garage door? If not, Model 7702CB Emergency conditions below apply to your installation. Additional Key Release is required. See Accessories page. materials may be required. You may find it helpful to • Look at the garage door where it meets the floor. refer back to this page and the accompanying Any gap between the floor and the bottom of the il
Streszczenie treści zawartej na stronie nr. 5
Planning (Continued) WARNING WARNING ONE-PIECE DOOR INSTALLATIONS Without a properly working safety reversal system, persons (particularly small children) could be • Generally, a one-piece door does not require CAUTION WARNING SERIOUSLY INJURED or KILLED by a closing garage reinforcement. If your door is lightweight, refer to door. the information relating to sectional doors in • The gap between the bottom of the garage door and Installation Step 11. the floor MUST NOT exceed 1/4" (6 mm). Otherw
Streszczenie treści zawartej na stronie nr. 6
LOCK LIGHT Carton Inventory Your garage door opener is packaged in one carton FOAM. Hardware for assembly and installation is which contains the motor unit and all parts illustrated shown on the next page. Save the carton and below. Accessories will depend on the model packing material until installation and adjustment is purchased. If anything is missing, carefully check the complete. packing material. PARTS MAY BE STUCK IN THE ® SECURITY✚ 3-Button ® Remote Control with Visor Clip (2) SECURITY
Streszczenie treści zawartej na stronie nr. 7
Hardware Inventory Separate all hardware and group as shown below for the assembly and installation procedures. ASSEMBLY HARDWARE Bolt 1/4"-20x1-3/4 (1) Lock Washer Nut 3/8" (1) 3/8" (1) Bolt 1/4"-20x2-1/2 (1) Lock Nut 1/4"-20 (2) Master Idler Bolt (1) Link (2) Trolley Threaded Shaft (1) INSTALLATION HARDWARE Spacer (2) Carriage Bolt Wing Nut Ring Nut 5/16"-18 (8) Handle Fastener (3) 1/4"-20x1/2" (2) 1/4"-20 (2) Lag Screw Hex Bolt Insulated 5/16"-9x1-5/8" (2) 5/16"-18x7/8" (4) Staples (30) Loc
Streszczenie treści zawartej na stronie nr. 8
WARNING WARNING ASSEMBLY STEP 1 CAUTION WARNING Assemble the Rail & Install the Trolley To prevent INJURY from pinching, keep hands and fingers away from the joints while assembling the rail. To avoid installation difficulties, do not run the garage door opener until instructed to do so. The front rail has a cut out “window” at the door end 3. Place the motor unit on packing material to protect (see illustration). The hole above this window is the cover, and rest the back end of the rail on top.
Streszczenie treści zawartej na stronie nr. 9
WARNING WARNING ASSEMBLY STEP 2 CAUTION WARNING Fasten the Rail to the Motor Unit To avoid SERIOUS damage to garage door opener, use ONLY those bolts/fasteners mounted in the top of • Insert a 1/4"-20x2-1/2 bolt, washer and spacer into the opener. the cover protection bolt hole on the back end of the rail as shown. Install lower spacer and washer then tighten securely with a 1/4"-20 lock nut. Do Hex Screws 8-32x7/16 NOT overtighten. • Remove the bolt and lock nut from the top of the motor unit
Streszczenie treści zawartej na stronie nr. 10
ASSEMBLY STEP 4 WARNING WARNING Install the Chain/Cable To avoid possible SERIOUS INJURY to fingers from moving garage door opener: 1. Pull the cable around the idler pulley and toward CAUTION WARNING • ALWAYS keep hand clear of sprocket while operating the trolley. opener. 2. Connect the cable to the retaining slot on the • Securely attach chain spreader BEFORE operating. trolley, as shown (Figure 1): • From below, push pins of master link bar up Dispensing Carton through cable link and trolley
Streszczenie treści zawartej na stronie nr. 11
ASSEMBLY STEP 5 Figure 1 Trolley Outer Lock Threaded Tighten the Chain Nut Washer Shaft To Tighten Outer Nut • Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley. Inner Nut • To tighten the chain, turn outer nut in the direction shown (Figure 1). To Tighten Inner Nut • When the chain is approximately 1/4" (6 mm) above the base of the rail at its midpoint, re-tighten Figure 2 the inner nut to secure the adjustment. Sprocket noise can result if chain is too
Streszczenie treści zawartej na stronie nr. 12
INSTALLATION STEP 1 Unfinished Ceiling Determine the Header Bracket OPTIONAL CEILING Location MOUNT FOR HEADER BRACKET WARNING WARNING Header Wall 2x4 To prevent possible SERIOUS INJURY or DEATH: Vertical Centerline of Garage Door • Header bracket MUST be RIGIDLY fastened to CAUTION WARNING 2x4 structural support on header wall or ceiling, otherwise Structural Supports garage door might not reverse when required. DO NOT install header bracket over drywall. • Concrete anchors MUST be used if moun
Streszczenie treści zawartej na stronie nr. 13
Wall Mount INSTALLATION STEP 2 Install the Header Bracket You can attach the header bracket either to the wall UP above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided). Optional Mounting Holes WALL HEADER BRACKET INSTALLATION • Center the bracket on the vertical centerline with Vertical the bottom edge of the bracket o
Streszczenie treści zawartej na stronie nr. 14
INSTALLATION STEP 3 Attach the Rail to the Header Bracket NOTE: (Optional) With some existing installations, you may re-use the old header bracket with the two plastic spacers included in the hardware bag. Place the spacers inside the bracket on each side of the rail, as illustrated. • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help. Have someone hold the opener securely on a temp
Streszczenie treści zawartej na stronie nr. 15
WARNING WARNING INSTALLATION STEP 4 CAUTION WARNING Position the Opener To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door. Follow instructions which apply to your door type as illustrated. SECTIONAL DOOR OR ONE-PIECE DOOR WITH TRACK A 2x4 laid flat is convenient for setting an ideal door-to-rail distance. Rail • Remove foam packaging. • Raise the opener onto a stepladder. You will need help at this point if the ladder is not tall enough. • Open
Streszczenie treści zawartej na stronie nr. 16
INSTALLATION STEP 5 WARNING WARNING Hang the Opener To avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY to structural Three representative installations are shown. Yours CAUTION WARNING supports of the garage. Concrete anchors MUST be used may be different. Hanging brackets should be angled if installing ANY brackets into masonry. (Figure 1) to provide rigid support. On finished ceilings (Figure 2 and Figure 3), attach a sturdy metal bracket to structural suppo
Streszczenie treści zawartej na stronie nr. 17
LOCK LIGHT LOCK LIGHT WARNING WARNING INSTALLATION STEP 6 CAUTION WARNING Install the Door Control To prevent possible SERIOUS INJURY or DEATH from electrocution: Locate door control within sight of the door at a • Be sure power is not connected BEFORE installing door minimum height of 5 feet (1.5 m) where small children control. cannot reach, and away from moving parts of the door • Connect ONLY to 24 VOLT low voltage wires. and door hardware. The installation surface must be To prevent possib
Streszczenie treści zawartej na stronie nr. 18
NOTICE WARNING WARNING INSTALLATION STEP 7 CAUTION WARNING Install the Lights To prevent possible OVERHEATING of the endpanel or light socket: • Install a 100 watt maximum light bulb in each • DO NOT use short neck or specialty light bulbs. socket. Light bulb size should be A19, standard • DO NOT use halogen bulbs. Use ONLY incandescent. neck only. The lights will turn ON and remain lit for To prevent damage to the opener: approximately 4-1/2 minutes when power is • DO NOT use bulbs larger th
Streszczenie treści zawartej na stronie nr. 19
INSTALLATION STEP 9 WARNING WARNING Electrical Requirements To prevent possible SERIOUS INJURY or DEATH from electrocution or fire: To avoid installation difficulties, do not run the CAUTION WARNING • Be sure power is not connected to the opener, and opener at this time. disconnect power to circuit BEFORE removing cover to To reduce the risk of electric shock, your garage door establish permanent wiring connection. opener has a grounding type plug with a third • Garage door installation and wiri
Streszczenie treści zawartej na stronie nr. 20
INSTALLATION STEP 10 WARNING WARNING ® Install The Protector System Be sure power is not connected to the garage door opener BEFORE installing the safety reversing sensor. The safety reversing sensor must be connected CAUTION WARNING To prevent SERIOUS INJURY or DEATH from a closing and aligned correctly before the garage door garage door: opener will move in the down direction. • Correctly connect and align the safety reversing sensor. This required safety device MUST NOT be IMPORTANT INFORMAT
