Streszczenie treści zawartej na stronie nr. 1
Installation and Wire
English
connection manual
VRX835
Installation and Wire connection manual
Contents
1. BEFORE STARTING ............................................................... 47
2. PACKAGE CONTENTS ........................................................... 47
3. GENERAL CAUTIONS ............................................................ 48
4. CAUTIONS ON INSTALLATION .............................................. 48
5. INSTALLING THE MAIN UNIT ...................................
Streszczenie treści zawartej na stronie nr. 2
Installation and Wire English connection manual 3. GENERAL CAUTIONS 1. Do not open the case. There are no user ser- 2. Use a soft, dry cloth to clean the case. Never viceable parts inside. If you drop anything use a rough cloth, thinner, benzine, or alco- into the unit during installation, consult your hol, etc. For tough dirt, apply a little cold or dealer or an authorized CLARION service warm water to a soft cloth and wipe off the centre. dirt gently. 4. CAUTIONS ON INSTALLATION 1. Prepare a
Streszczenie treści zawartej na stronie nr. 3
Installation and Wire English connection manual 5. INSTALLING THE MAIN UNIT Universal Mount 1. Place the universal mounting bracket into the instrument panel, use a screwdriver to bend each stopper of the universal mounting bracket inward, then secure the stopper as shown in Figure 6. 2. Wire as shown in Section 8. Notes: 3. Insert the main unit into the universal mount- 1) Some car models require special mounting kits ing bracket until it locks. for proper installation. Consult your Clarion
Streszczenie treści zawartej na stronie nr. 4
Installation and Wire English connection manual Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles) This unit is designed for fixed installation in the rection of arrow to remove it. Repeat the dashboard. same for the other side to remove the springs from the both sides. (Figure 7) If the vehicle is equipped with a factory-installed radio, install the main unit with the parts and 2. Secure the mounting brackets to the chassis screws marked (∗). (Figure 8) as shown in Figure 8. Hol
Streszczenie treści zawartej na stronie nr. 5
Installation and Wire English connection manual 6. REMOVING THE MAIN UNIT 1. When the rear of the main unit has been se- pull the main unit out by the hook plate. (In- cured with the method shown in Figure 6 un- sert both the right and left edges of the hook fasten the special screw. plate.) (Figure 9) 2. Remove the outer escutcheon. Note: Keep the hook plate. You cannot remove the 3. Insert the hook plate between the spring and main unit without disengaging the hook plate. the universal mounti
Streszczenie treści zawartej na stronie nr. 6
Installation and Wire English connection manual 8. WIRE CONNECTION Securely connect to the metal part of the car with a Black Earth (ground) cord screw, etc. Choke coil Main power supply cord Yellow 3A Fuse CeNET cable (provided with this unit) CeNET cable (Sold separately) Subwoofer output terminal L+R (RCA) Power supply lead Front audio output (input) terminal L+R (RCA) ∗4 & Rear audio output (input) terminal L+R (RCA) ∗4 Reset switch DSP select switch (∗3) Tuner amp unit ∗1 Top view of
Streszczenie treści zawartej na stronie nr. 7
Installation and Wire English connection manual Purple/Black 2 Purple 1 Green/Black 8 Blue/White 0 Green 7 Brawn (∗1 Glay 3 Grass-green ¡ No. Description Glay/Black B 1 REAR RIGHT 4 2 REAR RIGHTv B 3 FRONT RIGHT Orange/White ! v 4 FRONT RIGHT 5 FRONT LEFTB White/Black 6 FRONT LEFTv 6 B 7 REAR LEFT Red 8 REAR LEFTv @ 9 +12 V MAIN POWER White 0 AUTO ANTENNA 5 ! ILLUMINATION @ +12 V ACCESSORY Yellow 9 # GROUND $ CCD/M.LOCK terminal ) % VISUAL 2 terminal Black ¥ Radio antenna jack (∗2) # & CeNET ter
Streszczenie treści zawartej na stronie nr. 8
Installation and Wire English connection manual Connecting the Accessories • Connection to the external amplifier The external amplifier cannot be connected unless the DSP is connected. For detailed information, refer to the instruction manual of the DSP. • Connection to the CCD camera for vehicle The CCD camera for vehicle can be connected to the CCD terminal on the main unit. For detailed information, refer to the instruction sheet or manual for the CCD camera. Notes: • A power supply box
Streszczenie treści zawartej na stronie nr. 9
Installation and Wire English connection manual RCA video cable (included the VCZ625) 9. SAMPLE SYSTEMS Sample System 1 VRX835 Front Speakers Rear Speakers RCA video cable (sold separately) Tuner Amp Unit Rear View DVD input Monitor TV Tuner input CeNET cable RCA video cable (included the (included the TV tuner) TV tuner) TV tuner (TTX7501z) CeNET Cable (included the Changer) Ferrite clamp CeNET Y-adapter (Included the DVD changer) (CCA-519-500, sold separately) DVD Changer CD Changer (V
Streszczenie treści zawartej na stronie nr. 10
RCA video cable (included the VCZ625) Installation and Wire English connection manual Sample System 2 VRX835 RCA video cable Rear View (sold separately) Monitor AV Adapter cable (CCA-389, sold separately) VTR Tuner Amp Unit DVD input Front Speakers TV Tuner input CeNET cable RCA video cable (included (included the TV tuner) the TV RCA cable tuner) (sold separately) CeNET Rear 4-Channel TV Tuner Speakers Amplifier (TTX7501z) CeNET cable (included the Sub-woofer DPH910) 2-Channel Ampli
