Instrukcja obsługi Philips 20TA1000/98

Streszczenie treści zawartej na stronie nr. 1

Quick Start Guide
Quick Start Guide
CONTENTS
IMPORT ANT
NOTE: This quick setup guide is used with several
INSTALLING LCD TV ON THE WALL . . 1 TUNER MODE CONTROL . . . . . . . . . . . . . 5
different LCD TV models. Not all features (and drawings)
UNFOLD THE BASE. . . . . . . . . . . . . . . 1 AUTO PROGRAM (SETTING UP
discussed in this manual will necessarily match those
TV CHANNEL INSTALLATION . . . . . . . . 2 CHANNELS) . . . . . . . . . . . . . . . . . . . . 5
found with your LCD TV set. Th

Streszczenie treści zawartej na stronie nr. 2

TV CHANNEL INSTALLATION Quick Start Guide Immediately after unpacking and plugging in your new television, run the auto program function to set up the TV for the broadcast or cable channels available in your area. If you do not run the auto program function to set up the channels , your television may not operate properly. MAIN CONTROLA Please follow these steps to install TV channels: PICTURE LANGUAGE AUDIO AUTO PROGRAM A/CH FEATURES MANUAL STORE Select a TV source via AV button on your remo

Streszczenie treści zawartej na stronie nr. 3

ACCESSORIES BATTERY INSTALLATION When you unpack this unit, make sure it includes the Remove the battery compartment lid on 1 the bottom of the remote control. following: Place lithium cell in the remote control. 2 Be sure the (+) and (-) ends of the batteries line up as marked inside the battery (CR2025) compartment. 2 Reattach the battery (/79) (/98) compartment lid. 3 Power adapter & cable Owner`s Manual & Quick Start Guide Tuner L-Adapter Warranty Card 1 3 (/79) (/98) Power adapter &

Streszczenie treści zawartej na stronie nr. 4

ANTENNA TV A combination antenna receives normal broadcast channels (VHF 2–13 and UHF 14–69). Your connection is easy because there is only one 75 Ω (ohm) antenna jack on the side of your TV, and that’s where the antenna goes. If your antenna has a round cable (75 ohm) on the end, then 1 you’re ready to connect it to the LCD TV. If your antenna has fl at, twin-lead wire (300 ohm), you fi rst need to attach the antenna wires to the screws on a 300- to 75-ohm � adapter(not supplied). Outdoor o

Streszczenie treści zawartej na stronie nr. 5

AUTO PROGRAM (SETTING UP CHANNELS) Your LCD TV can automatically set itself for local area (or cable TV) channels. This makes it easy for you to select only the TV stations in your area by pressing the CH+ or CH- button. MAIN CONTROLA Press the MENU button on the remote control to show the 1 PICTURE LANGUAGE onscreen menu. AUDIO AUTO PROGRAM A/CH FEATURES MANUAL STORE Press the CURSOR DOWN button to INSTALL CHANNEL SETTING 2 FACTORY RESET highlight the INSTALL menu. 1 Press the CURSOR RIGHT bu

Streszczenie treści zawartej na stronie nr. 6

CABLE BOX (WITH RF IN / OUTPUTS): Connect the Cable TV signal to the IN jack (or RF IN or CABLE 1 The Cable TV signal from IN) on the Cable Box. the Cable Company � Connect an RF coaxial cable (not supplied) to the OUT jack (or � � 2 TO TV or RF OUT) of the Cable Box. OUTPUT CH 3 4 CABLE TO TV Connect the other end of the coaxial cable to one end of the IN 3 supplied L-Adapter as shown, and connect the other end of the adapter to the TV jack on the LCD TV. 75 � Coaxial Plug the DC

Streszczenie treści zawartej na stronie nr. 7

S-VIDEO CONNECTIONS The S-Video connection on the rear of the LCD TV can provide you with better picture detail and clarity for the playback of accessory S - V I DE O sources such as DBS (digital broadcast satellite), DVD (digital video discs), video games, and VHS VCR (video cassette recorder) tapes AU DI O than the normal antenna picture connections. V I D E O � � � � � � � � � � � � � � � � � � � � � � � � � Connect an S-Video cable to the S-VIDEO jack of the other 1 equipment (DVD Player

Streszczenie treści zawartej na stronie nr. 8

PC (MONITOR) INPUTS: This LCD TV can be used as a PC. Your computer will have to be equipped with a VGA type video output and interface cable (not supplied). (One end with VGA type connector, the other end with D-SUB type connector.) Connect VGA end of the interface cable (not supplied) to the 1 computer, while connecting the other ends to the D-SUB INPUT jack on the LCD TV. � ���� Although audio connections are not required, the LCD TV can 2 reproduce the computers audio out by an AUDIO