Streszczenie treści zawartej na stronie nr. 1
Pub. 988-0151-421
www.eaglesonar.com
®
FishEasy 250 DS
®
& SeaFinder 250 DF
Fish-Finding & Depth-Sounding Sonars
Installation and Operation
Instructions
Streszczenie treści zawartej na stronie nr. 2
Copyright © 2006 LEI-Eagle All rights reserved. No part of this manual may be copied, reproduced, republished, transmitted or distributed for any purpose, without prior written consent of Eagle Electronics. Any unauthorized commercial distribution of this manual is strictly prohibited. ® Eagle is a registered trademark of LEI ® ® FishEasy 250 & Seafinder 250 are registered trademarks of LEI. Eagle Electronics may find it necessary to change or end our policies, regulations, and special offers a
Streszczenie treści zawartej na stronie nr. 3
Table of Contents Section 1: Introduction....................................................................1 Specifications: FishEasy 250 DS & SeaFinder 250 DF ...............1 How Sonar Works.................................................................................3 Preparations .........................................................................................4 Section 2: Installation & Accessories..........................................7 Recommended Tools and Supplies
Streszczenie treści zawartej na stronie nr. 4
FishTrack™ ........................................................................................46 Alarms.................................................................................................47 Fish Alarm..........................................................................................47 Depth Alarms .....................................................................................47 Shallow Alarm...........................................................................
Streszczenie treści zawartej na stronie nr. 5
Section 1: Introduction Thank you for buying an Eagle sonar! Your unit is a high-quality so- nar designed for both professional and novice fishermen. All Eagle so- nars have an automatic mode that finds and displays the bottom, fish, underwater structure and more – right out of the box. All you have to do is press the on (PWR) key. To get started with your Eagle sonar, first read the installation section. It contains instructions for mounting the sonar unit, the transducer and any optional acc
Streszczenie treści zawartej na stronie nr. 6
Back-up memory:...........Built-in memory stores sonar settings when unit is turned off. Languages: ......................11 International languages. Sonar Frequency: ......................83/200 kHz for FishEasy 250 DS; 50/200 kHz for SeaFinder 250 DF. Transducers:...................FishEasy 250 DS: a compact Dual-Search Skimmer transducer with built-in tempera- ture sensor is packed with the unit. SeaFinder 250 DF: a dual-frequency Skim- mer transducer with built-in temperature sensor is
Streszczenie treści zawartej na stronie nr. 7
NOTICE! The storage and operation temperature range for your unit is from -4 degrees to +167 degrees Fahrenheit (-20 degrees to +75 degrees Celsius). Extended storage or operation in temperatures higher or lower than specified will damage the liquid crystal display in your unit. This type of damage is not covered by the warranty. For more information, contact the factory's Customer Service Department; phone numbers are inside the manual's back cover. How Sonar Works Sonar has been around since t
Streszczenie treści zawartej na stronie nr. 8
Dual Search & Dual Frequency The FishEasy 250 DS is packed with a Dual Search Skimmer Trans- ducer that can transmit at 83 kHz and 200 kHz. The SeaFinder 250 DF has a dual frequency transducer that transmits at 50kHz and 200kHz. A new innovation, the 83 kHz frequency offers superior sonar perform- ance at all depths from very shallow up to 1,000 ft and provides up to 120º of fishfinding coverage. Preparations You can install the sonar system in some other order if you prefer, but we recommend th
Streszczenie treści zawartej na stronie nr. 9
This will help you make sure you have enough cable length for the de- sired configuration. 2. Determine the approximate location for the transducer and its cable route. 3. Determine the location of your battery or other power connection, along with the power cable route. 4. Install the transducer and route the transducer cable to the sonar unit. 5. Install the power cable and route it to the sonar unit. 6. Mount the sonar unit. 5
Streszczenie treści zawartej na stronie nr. 10
Notes 6
Streszczenie treści zawartej na stronie nr. 11
Section 2: Installation & Accessories These instructions will help you install your Skimmer transducer on a transom, on a trolling motor or inside a hull. Please read all instruc- tions before proceeding with any installation. Your Skimmer transducer typically comes packaged with a one-piece stainless steel bracket for mounting it to the transom of your boat. The optional trolling motor mount uses a one-piece plastic bracket with an adjustable strap. These are "kick-up" mounting brackets. Th
Streszczenie treści zawartej na stronie nr. 12
Shoot-through hull installations Tools: these will vary depending on your hull's composition. Consult your boat dealer or manufacturer. Supplies: 100 grit sandpaper, good quality epoxy adhesive. Selecting a Transducer Location 1. The transducer must be placed in a location that has a smooth flow of water at all times. If the transducer is to be mounted inside the hull, then the chosen location must be in the water at all times. If the transducer is not placed in a smooth flow of water, interfere
Streszczenie treści zawartej na stronie nr. 13
CAUTION: Clamp the trans- ducer cable to transom near the transducer. This will help prevent the transducer from entering the boat if it is knocked off at high speed. Good location Poor location Good location Good location Poor angle Good and poor transducer locations. How low should you go? For most situations, you should install your Skimmer transducer so that its centerline is level with the bottom of the boat hull. This will usually give you the best combination of smooth water flow and prot
Streszczenie treści zawartej na stronie nr. 14
transducer up or down. If you frequently lose bottom signal lock while running at high speed, the transducer may be coming out of the water as you cross waves or wakes. Move the transducer a little lower to help prevent this. If you cruise or fish around lots of structure and cover, your transducer may be frequently kicking up from object strikes. If you want, you may move the transducer a little higher for more protection. There are two extremes you should avoid. Never let the edge of the mount
Streszczenie treści zawartej na stronie nr. 15
Third, a transducer CAN NOT shoot through wood and metal hulls. Those hulls require either a transom mount or a thru-hull installation. Fourth, if your Skimmer transducer has a built in temp sensor, it will only show the temperature of the bilge, not the water surface temp. Follow the testing procedures listed in the shoot-thru-hull installation section at the end of this instruction booklet to determine if you can satisfactorily shoot through the hull. Transom Transducer Assembly and Mounting T
Streszczenie treści zawartej na stronie nr. 16
If the transducer's face isn't parallel with the ground, remove the transducer and ratchets from the bracket. Place the ratchets into the holes in the bracket with the letter "B" aligned with the dot stamped in the bracket. Reassemble the transducer and bracket and place them against the transom. Again, check to see if you can move the transducer so it's parallel with the ground. If you can, then go to step 3. If it doesn't, repeat step 2, but use a different alignment letter until you can place
Streszczenie treści zawartej na stronie nr. 17
Metal washer Nut Rubber Metal washer washers Bolt Assemble transducer and bracket. 4. Drilling mounting holes. Hold the transducer and bracket assembly against the transom. The transducer should be roughly parallel to the ground. The transducer's centerline should be in line with the bottom of the hull. Don't let the bracket extend below the hull! Mark the center of each slot for the mounting screw pilot holes. You will drill one hole in the center of each slot. Drill the holes using the #29 bi
Streszczenie treści zawartej na stronie nr. 18
Route cable over bolt and through bracket. Side view (left) and shown from above (right). Attach the transducer to the transom. Slide the transducer up or down until it's aligned properly with the bottom of the hull as shown in the preceding and following figures. Tighten the bracket's mount- ing screws, sealing them with the sealant compound. Adjust the transducer so that it's parallel to the ground and tighten the nut until it touches the outer washer, then add 1/4 turn. Don't over tight
Streszczenie treści zawartej na stronie nr. 19
Electrical noise from the engine's wiring, bilge pumps, VHF radio wires and cables, and aerators can be picked up by the sonar. Use caution when routing the transducer cable around these wires. WARNING: Clamp the transducer cable to the transom close to the transducer. This can prevent the transducer from enter- ing the boat if it is knocked off at high speed. If you need to drill a hole in the transom to pass the connector through, the required hole size is 5/8". Caution: If you drill a hole in
Streszczenie treści zawartej na stronie nr. 20
2. Slide the adjustable strap supplied with the TMB-S through the slot in the transducer bracket and wrap it around the trolling motor. Po- sition the transducer to aim straight down when the motor is in the water. Tighten the strap securely. 3. Route the transducer cable alongside the trolling motor shaft. Use plastic ties (not included) to attach the transducer cable to the troll- ing motor shaft. Make sure there is enough slack in the cable for the motor to turn freely. Route the cable to the