Instrukcja obsługi Metra Electronics 99-8204

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION INSTRUCTIONS FOR PART 99-8204
APPLICATIONS
2003-2008 Toyota Corolla
99-8204
KIT FEATURES
• DDIN Head Unit Provision with Pocket
• ISO DIN Head Unit Provision with Pocket
KIT COMPONENTS
A) Radio Housing • B) Pocket • C) Trimplate • D) Mounting Brackets • E) ISO Brackets • F) Rear Support Bracket
G) (8) #8x3/8” Phillips Flat Head Screws • H) (4) #8x3/8” Phillips Pan Head Screws
C
A
B D
F
G H
E
TOOLS REQUIRED:
Socket Wrench • Phillips Screwdriver
1-800-2

Streszczenie treści zawartej na stronie nr. 2

99-8204 TABLE OF CONTENTS Dash Disassembly ............................................................................ 1 Kit Assembly ................................................................................. 2-3 Final Assembly ................................................................................. 4

Streszczenie treści zawartej na stronie nr. 3

99-8204 DASH DISASSEMBLY 2003-2008 TOYOTA COROLLA Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap the gear shifter trim bezel and remove. Remove the center climate control knob and (1) Phillips screw exposed. Unclip the climate control bezel/pocket assembly and remove. Remove (4) 10 mm bolts from the bottom of the factory head unit. Remove the factory head unit/trim bezel assembly and disconnect the wiring. Unclip the bezel from the head unit and remove

Streszczenie treści zawartej na stronie nr. 4

99-8204 KIT ASSEMBLY 2003-2008 TOYOTA COROLLA Attach the Pocket to the back of the Radio Housing (by holding the Housing upside-down, inserting the right edge of the Pocket into place and pushing the rest of the Pocket onto the lip) and mount with (2) #8 x 3/8" Phillips Pan-head Screws supplied. Secure the Mounting Brackets to the Pocket with (8) #6 x 1/4" Phillip Flat-head Screws supplied. Mount the Rear Support Bracket to the back of the Pocket with (2) #8 x 3/8" Phillips Pan-head Screws supp

Streszczenie treści zawartej na stronie nr. 5

99-8204 KIT ASSEMBLY DIN HEAD UNIT PROVISION A Slide the DIN cage into the Radio Housing 1 and secure by bending the metal locking tabs down. Slide the aftermarket head unit into the cage and secure. ISO DIN HEAD UNIT PROVISION B1 Align the holes in the ISO Brackets mount 1 the Brackets to the head unit with the screws supplied with the unit. Slide the head unit/bracket assembly into the radio opening until the side clips engage and snap the Trimplate over the unit. (See Fig. B1) B2 NOTE: To re

Streszczenie treści zawartej na stronie nr. 6

99-8204 FINAL ASSEMBLY FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring

Streszczenie treści zawartej na stronie nr. 7

99-8204 NOTES 5

Streszczenie treści zawartej na stronie nr. 8

99-8204 INSTRUCTIONS 1-800-221-0932 www.metraonline.com © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST99-8204 REV. 10/02/07