Instrukcja obsługi Metra Electronics 99-7867

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION INSTRUCTIONS FOR PART 99-7867
APPLICATIONS
Acura RSX
2002-2006
99-7867
KIT FEATURES
• DIN Radio Provision
• ISO Radio Provision
KIT COMPONENTS
A) Radio Housing • B) ISO Trim Plate • C) ISO Brackets
B
C
A
TOOLS REQUIRED:
• Phillips Screwdriver • Panel Removal Tool
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2007 METRA ELECTRONICS CORPORATION

Streszczenie treści zawartej na stronie nr. 2

99-7867 TABLE OF CONTENTS Dash Disassembly - Acura RSX 2002-2006 .... ......... ....... ........ ........ ....... .1 Kit Preparation . . . . ...... ................................. ...... 2 Kit Assembly - DIN Radio Provision ..... . ....... ........ ....... ........ ... ..... . 3 - ISO Radio Provision . . . ......... . .......................... ......3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 *Note: Refer also to the instructions in

Streszczenie treści zawartej na stronie nr. 3

99-7867 DASH DISASSEMBLY ACURA RSX 2002-2006 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip the power outlet panel and remove (2) Phillips screws exposed facing up. (“A” in Figure A) Unclip the radio trim panel assembly 3 (including the head unit and the haz- ard switch) then unplug and remove the assembly. (Figure A) B 4 Remove (4) Phillips screws securing the factory head unit to the bracket "C" assembly and remove the unit. (“B” in Figure A) "C

Streszczenie treści zawartej na stronie nr. 4

99-7867 KIT PREPARATION ACURA RSX 2002-2006 A 1 Mount the hazard switch to the back of the radio housing with (2) Phillips screws previously removed in Step 7 of the disassembly. (Figure A) 2 Mount the factory bracket assembly to the back of the radio housing with (4) Phillip screws previously removed in Step 6 of the disassembly. ( Figure B) Continue to kit assembly. B 2

Streszczenie treści zawartej na stronie nr. 5

99-7867 KIT ASSEMBLY DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the radio hous- ing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure A) Continue to final assembly. ISO RADIO PROVISION A 1 Mount the ISO brackets to the radio using the screws supplied with the radio. (Figure A) 2 Slide the radio into the radio housing until

Streszczenie treści zawartej na stronie nr. 6

99-7867 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

Streszczenie treści zawartej na stronie nr. 7

99-7867 NOTES 5

Streszczenie treści zawartej na stronie nr. 8

99-7867 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 11/02/07 © COPYRIGHT 2007 METRA ELECTRONICS CORPORATION INST99-7867