Instrukcja obsługi Metra Electronics 95-8152

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION INSTRUCTIONS FOR PART 95-8152
APPLICATIONS
LEXUS GS 300/400
1998-2005
Not For Use In Vehicles
With Factory Navigation
95-8152
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Double DIN Radio Housing B) Double DIN Brackets
A
B
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2007 METRA ELECTRONICS CORPORATION

Streszczenie treści zawartej na stronie nr. 2

95-8152 TABLE OF CONTENTS Dash Disassembly - Lexus GS 300/400 1998-2005 . . . . . . . . . . . . . . . . . . . .. 1,2 Kit Assembly - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 *Note: Refer also to the instructions included with the aftermarket radio.

Streszczenie treści zawartej na stronie nr. 3

H H M M 95-8152 DASH DISASSEMBLY LEXUS GS 300/400 1998-2005 1 Disconnect the negative battery ter- A minal to prevent an accidental short circuit. 2 Unsnap and remove vent/clock assembly from above climate con- trols. (Figure A) 3 Remove two screws from behind vent/clock assembly. (Figure B) 4 Unsnap and remove ashtray assembly from below radio. (Figure C) B Continued on next page. C 1

Streszczenie treści zawartej na stronie nr. 4

95-8152 DASH DISASSEMBLY LEXUS GS 300/400 1998-2005 5 Remove (2) screws from behind ash- D tray assembly. (Figure D) 6 Unplug and remove radio/climate controls assembly. (Figure E) 7 Remove side brackets to separate the radio from the climate controls. (Retain the climate controls for reuse during kit assembly.) (Figure F) Continue to kit assembly. E F 2

Streszczenie treści zawartej na stronie nr. 5

95-8152 KIT ASSEMBLY LEXUS GS 300/400 1998-2005 DOUBLE DIN RADIO STACKED ISO MOUNT UNITS PROVISION Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN Brackets onto the Double DIN Radio Housing. (Figure A) 2 Slide the factory climate controls into the Bracket/Radio Housing assembly aligning the top of the assembly with alignment pins in the bottom of the climate controls and secure using the factory hardware. (Figure B) 3 Slide the Double DIN or

Streszczenie treści zawartej na stronie nr. 6

95-8152 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

Streszczenie treści zawartej na stronie nr. 7

95-8152 NOTES 5

Streszczenie treści zawartej na stronie nr. 8

95-8152 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 04/24/08 © COPYRIGHT 2007 METRA ELECTRONICS CORPORATION INST95-8152