Instrukcja obsługi Metra Electronics 99-2004

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION INSTRUCTIONS FOR PART 99-2004
APPLICATIONS
Cadillac
1997-2001 Catera
1996-1999 Deville (Column Shift Only)
99-2004
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO DIN Radio Provision with Pocket
KIT COMPONENTS
( A) Radio Housing • ( B) Trim Plate • ( C) ISO Brackets • (D) (4) Speed Clips • (E) (4) Phillips head screws
D
B C
A
E
TOOLS REQUIRED:
Phillips Screwdriver • Cutting Tool
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004 METRA ELECTRONICS CORPO

Streszczenie treści zawartej na stronie nr. 2

99-2004 TABLE OF CONTENTS Dash Disassembly 1997-2001 Cadillac Catera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1996-1999 Cadillac Deville ( Column Shift Only) ............. 1 Kit Assembly 1997-2001 Cadillac Catera DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . 2 ISO DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . 2 1996-1999 Cadillac Deville ( Column Shift Only) DIN Radio Provision with Pocket . . . . . . . .

Streszczenie treści zawartej na stronie nr. 3

DASH DISASSEMBLY 99-2004 1997-2001 CADILLAC CATERA 1 Disconnect the negative battery A terminal to prevent an accidental short circuit. 2 Remove (1) Phillips head screw from inside the ashtray and remove ash- tray. (Figure A) 3 Remove screw covers from the radio trim panel. Remove traction control B and hazard switch covers. Then remove switches by depressing tabs and pulling outward. (Figure B) Remove (4) Phillips head screws 4 from behind covers and ashtray. Remove radio trim panel and unplug

Streszczenie treści zawartej na stronie nr. 4

KIT ASSEMBLY 99-2004 1997-2001 CADILLAC CATERA 1 Remove (2) tabs from the top edge 2 Remove both mounting brackets “B” of the radio housing. (Figure A) from the radio housing. (Figure B) B A TWO ON EACH SIDE OF RADIO HOUSING DIN RADIO PROVISION Slide the radio into the DIN 4 3 Slide the DIN cage into the radio cage/housing assembly until it snaps housing and secure by bending the into place. (Figure B) metal locking tabs outward. (Figure A) B A Continue with final assembly. 5 ISO RADIO PROVISIO

Streszczenie treści zawartej na stronie nr. 5

KIT ASSEMBLY 99-2004 1996-1999 CADILLAC DEVILLE 1 Install (4) speed clips into the sub- 2 Remove mounting brackets “A” from dash mounting positions. (Figure A) the radio housing. (Figure B) B A TWO ON EACH SIDE OF RADIO HOUSING DIN RADIO PROVISION Slide the radio into the DIN 4 3 Slide the DIN cage into the radio cage/housing assembly until it snaps housing and secure by bending the into place. (Figure B) metal locking tabs outward. (Figure A) B A Continue with final assembly. 5 ISO RADIO PROVI

Streszczenie treści zawartej na stronie nr. 6

FINAL ASSEMBLY 99-2004 FINAL ASSEMBLY Locate the factory wiring harness in the dash and make the connection as shown. 1 Metra recomends using the proper mating adapter and making the connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.) Re-connect the negative battery terminal and test the unit for proper operation. 2 3 Reassemble radio and dash assemblies in reverse order of disassembly. FINAL WIRING CONNECTIONS Make wiring

Streszczenie treści zawartej na stronie nr. 7

99-2004 NOTES 5

Streszczenie treści zawartej na stronie nr. 8

INST992004 1-800-221-0932 www.metraonline.com REV. 12/06/07 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST99-2004