Instrukcja obsługi Metra Electronics 95-8223

Streszczenie treści zawartej na stronie nr. 1

INSTALLATION INSTRUCTIONS FOR PART 95-8223
APPLICATIONS
Toyota Corolla
2009-10
95-8223/
95-8223S
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• Painted To Match Factory Dash
95-8223= BLACK
95-8223S= SILVER
KIT COMPONENTS
• A) Radio Housing Trim Plate • B) Double Din Trim Plate
Harness & Antenna Connections (sold separately)
• 70-1761 Toyota Harness 87-up
• TYTO-01 Toyota Amp Interface 03-up
B
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Too

Streszczenie treści zawartej na stronie nr. 2

95-8223 TABLE OF CONTENTS Dash Disassembly - Toyota Corolla 2009-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Kit Assembly - Double DIN/Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . 2 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 *Note: Refer also to the instructions included with the aftermarket radio. KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most re

Streszczenie treści zawartej na stronie nr. 3

95-8223 DASH DISASSEMBLY Toyota Corolla 2009-10 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove the (4) side trim panels from the right and left side of the radio and a/c controls. (Figure A) 3 Unclip and remove the a/c vent panel above the factory radio.(Figure B) 4 Remove (4) 10 MM bolts securing the radio. (Figure C) B 5 Remove (8) screws securing the brackets to the factory radio and remove the brackets. (Retain the brackets for re-u

Streszczenie treści zawartej na stronie nr. 4

95-8223 KIT ASSEMBLY DOUBLE DIN/STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Attach the clips removed from the factory radio to the back of the radio housing trim plate. (Figure A) 2 Attach the factory mounting brackets and the Double DIN trim plates to the Double DIN or the stacked ISO mount unit(s) using the screws supplied with the unit(s). (Figure B) Continue to final assembly. B 2

Streszczenie treści zawartej na stronie nr. 5

95-8223 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble in reverse order of disassembly using the 95-8223 Rad

Streszczenie treści zawartej na stronie nr. 6

95-8223 NOTES 4

Streszczenie treści zawartej na stronie nr. 7

95-8223 NOTES 5

Streszczenie treści zawartej na stronie nr. 8

95-8223 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 04/29/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST95-8223