Instrukcja obsługi Denon 98D10

Streszczenie treści zawartej na stronie nr. 1

KeyMaster


- - your your codefree solution codefree solution
Installation manual
98D10
Denon DVD-1000
2000 HW-Parts & StoneDesign
HW-Parts

Streszczenie treści zawartej na stronie nr. 2

1.1 - Players. These installation instructions covers the installation of the Key- Master for DVD players manufactured by: Denon DVD-1000 ect . Please note: This installation manual will be updated later regar - www.stonedesign.dk/dvd/ I U K-V 1 All names, logos etc. are trademarks of their respective companies. All rights information in this document is subject to change without notice. reserved. The D10 98 ding the installation in the Denon DVD F100.

Streszczenie treści zawartej na stronie nr. 3

2.1 - Disclaimer! Read this throroughly. Before installing the KeyMaster player codefree, you should read through these warnings Ÿ We are not responsible for any illegal use of the KeyMaster. Ÿ We offer no warranty on your Ÿ The installation of the KeyMaster is at your own risk. Ÿ KeyMaster Ÿ If the manu fac tu re of the - makes chang guara nty the fun c Ÿ The KeyMaster and it is therefore necessary to be familiar with soldering, otherwise you should get a service r to do the installation for y

Streszczenie treści zawartej na stronie nr. 4

3.1 - Removal of the top cover. Remember to disconnect the player from the mains before - ding. each side and three on the back of the player as shown on fig. 1. Fig. 1 Note: The picture shows a Denon DVD-1000. two in topcover, Remove the seven screws which holds the proce

Streszczenie treści zawartej na stronie nr. 5

3.2 - Installing the KeyMaster. the la Fig. 2 Fig. 3 à . à . à Connect the orange wire onto the à . à - fig.3. pad as shown in Connect the brown onto the solder 634 and R R630 connection Connect the yellow wire onto the R631 and R627 connection R633 and R629 connection Connect the blue wire onto the R632 and R628 connection Connect the white wire onto the PCB board. st two has to be connected onto the powersupply and SCART Seven wires have to be soldered onto the PCB board in the fro

Streszczenie treści zawartej na stronie nr. 6

3.2 - Conitiune (powersupply)... fig. 4. Fig. 4 à R37 . Remember to adjust the ends of the wires so they will fit onto the . Do not change or remove any components. soldering pads as shown Connect the grey wire onto Connect the grey wire as shown in

Streszczenie treści zawartej na stronie nr. 7

3.2 - Conitiuned (SCART). connector, you have to make a small change. The controlling signal has to be moved to the KeyMaster function. It is necessary to do so because the player itself do not If the player is without a Scart connector the purple wire just has to It is before necessary to disconnect the original signal as shown in fig. 5. Fig. 5 à But it is very imponant that the wire is fitted as shown on the next page. Connect the purple wire onto the connector CY142 pin 8. be removed. con

Streszczenie treści zawartej na stronie nr. 8

3.2 - Contiuned (SCART). togher with the rest of the wires as shown on fig. 6 Fig. 6 down into the power supply mains parts. resson for this is that the purple wire otherwire will be able to drop with cable ties. The It is very imponant that the purple wire is placed and tired

Streszczenie treści zawartej na stronie nr. 9

3.3 - Securing KeyMaster. Secure the KeyMaster as shown in fig. 7. film from the double sided tape and press the KeyMaster thorough- bottom. Fig. 7 Note: The picture shows a Denon DVD-1000. ly towards the Remove the protection

Streszczenie treści zawartej na stronie nr. 10

3.4 - Assembling the player. Assembling the player is done using the following procedure: ΠJust refit the back on and secure it. 3.5 - Finishing up the installation. After turning the player on and off the KeyMaster is ready for use . The player and the KeyMaster y for use . about programming the KeyMaster look in the operating instructi - ons. Remember to test the player in both region 1 & 2. Enjoy our product, the KeyMaster. For details is now read topcover