Streszczenie treści zawartej na stronie nr. 1
INSTALLATION INSTRUCTIONS
UNDERCOUNTER DISHWASHER
INSTRUCTIONS D'INSTALLATION
LAVE-VAISSELLE SOUS PLAN DE TRAVAIL
Table of Contents .............................................................. 2
Table des matières .......................................................... 25
W10321619A
Streszczenie treści zawartej na stronie nr. 2
TABLE OF CONTENTS DISHWASHER SAFETY...............................................................................2 INSTALLATION REQUIREMENTS (CONT.) Determine Cabinet Opening................................................................... 14 INSTALLATION REQUIREMENTS .............................................................3 Install Door Handle (on some models) ...................................................14 Tools and Parts...........................................................
Streszczenie treści zawartej na stronie nr. 3
Other parts you may also need: INSTALLATION REQUIREMENTS Tools and Parts NOTES: Gather the recommended tools and parts before starting ■ Moisture barrier tape is recommended when installing a installation. Read and follow the instructions provided with any dishwasher under a wood countertop. tools listed here. ■ Parts available for purchase in plumbing supply stores. Check All Installations local codes. Check existing electrical supply. See “Electrical Requirements” section. It is recommen
Streszczenie treści zawartej na stronie nr. 4
Check location where dishwasher will be installed. The location must provide: Location Requirements ■ easy access to water, electricity and drain. Grounded electrical supply required. ■ convenient access for loading and unloading dishes. Do not run drain lines, water lines or electrical wiring where they Corner locations require a 2" (5.1 cm) minimum clearance can interfere with or contact dishwasher motor or legs. between the side of the dishwasher door and the wall or The location where t
Streszczenie treści zawartej na stronie nr. 5
5
Streszczenie treści zawartej na stronie nr. 6
Drain Requirements Electrical Requirements ■ A new drain hose is supplied with your dishwasher. If drain Be sure that the electrical connection and wire size are adequate hose is not long enough, use a new drain hose with a and in conformance with the National Electrical Code, ANSI/NFPA maximum length of 12' (3.7 m) (Part Number 3385556) that 70 - latest edition and all local codes and ordinances. meets all current AHAM/IAPMO test standards, is resistant to A copy of the above code standards
Streszczenie treści zawartej na stronie nr. 7
Prepare Cabinet Opening—Existing INSTALLATION INSTRUCTIONS Utilities WARNING Electrical Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. Failure to do so can result in death or electrical shock. If the water line and the cable extend to the locations shown, proceed to the “Install Drain Hose” section. If they do not reach far enough, follow the instructions in the “Prepare Cabinet Opening— New Utilities” section. Prepare Cabinet Op
Streszczenie treści zawartej na stronie nr. 8
Route cable from power supply through cabinet hole (cable must Wood cabinet: Sand the hole until smooth. extend to the right front side of cabinet opening). Tape cable to the floor in area shown. This will prohibit cable from moving when Metal cabinet: Cover hole with grommet included with power dishwasher is moved into cabinet opening. supply cord kit. Option B, Direct Wire: Prepare and Route Water Line Helpful Tip: Routing the water line through the left side of cabinet Helpful Tip: Wirin
Streszczenie treści zawartej na stronie nr. 9
. Connect the ³⁄₈" compression fitting to the water supply line prior Slowly route water supply line through hole in cabinet. (If you are to installing the unit into the cabinet opening. Attach such that the using copper tubing, it will bend and kink easily, so be gentle.) It ³⁄₄" connection is facing upward as shown above. should be far enough into the cabinet opening to connect it to the Copper tubing only: Put the tubing into the 90° elbow fitting as far dishwasher inlet on the front le
Streszczenie treści zawartej na stronie nr. 10
1. Connect black end of drain hose to waste tee and cut if needed. NOTE: Do not cut ribbed section. 2. Attach black end of drain hose to waste tee with a large silver drain hose clamp (provided). Use pliers to squeeze clamp open and move into position. If the drain hose was cut, use a 1¹⁄₂" to 2" (3.8 to 5 cm) screw- type clamp (not provided). IMPORTANT: The drain hose connection of the disposer or a waste tee must be made before the drain trap and at least 20" Option C, Waste disposer
Streszczenie treści zawartej na stronie nr. 11
Option D, No waste disposer – with air gap Prepare Dishwasher WARNING Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts. 1. Connect black end of drain hose to air gap and cut if needed. NOTE: Do not cut ribbed section. WARNING Excessive Weight Hazard 2. Attach drain hose to air gap with large silver drain hose clamp Use two or more people to move and install (provided). Use pliers to squeeze dishwa
Streszczenie treści zawartej na stronie nr. 12
NOTE: If using Option B, proceed to “Determine Cabinet Opening,” to continue with the installation of your dishwasher. Using a flat-blade screwdriver, turn the plastic fasteners ¹⁄₄ turn to unlock them. Remove panel. Do not remove tech sheet from Make Power Supply Cord Connection access panel. Option A, Power Supply Cord: Using a ¹⁄₄" hex head socket, nut driver or Phillips screwdriver, remove terminal box cover. Retain for later use. Route cord so that it does not touch dishwasher motor to
Streszczenie treści zawartej na stronie nr. 13
Connect wires black to black and white to white, using UL Listed/CSA Approved twist-on wire connectors (included with WARNING power supply cord kit). Electrical Shock Hazard Electrically ground dishwasher. If needed, see website for animated representation of this step. Connect ground wire to green ground connector in Visit www.jenn-air.com under FAQ tab. terminal box. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Tighten
Streszczenie treści zawartej na stronie nr. 14
Determine Cabinet Opening Built-up floors: If the kitchen floor is higher than the cabinet opening's floor - for example, the kitchen floor tile does not Measure height of cabinet opening from underside of countertop extend into the cabinet opening - add shims as needed in the area to floor where dishwasher will be installed (you will need to shown to bring the dishwasher up to 34" (86.4 cm) below the measure the lowest point on the underside of the countertop and countertop. the highest
Streszczenie treści zawartej na stronie nr. 15
Install Custom Panel (Model JDB3600AWX) NOTE: The handle for the custom panel is not included. IMPORTANT: If the handle is attached from the back of the custom panel, the screw holes should be countersunk for the screws heads to be flush with the panel. If the handle is attached to the front of the custom panel, the screw lengths cannot exceed ® the panel thickness. For more information on Jenn-Air custom ® handle selection, refer to the Jenn-Air Catalog, visit www.jenn-air.com, or call 1
Streszczenie treści zawartej na stronie nr. 16
Attach outer panel to back of customer-supplied custom panel with the four #10-16 x ³⁄₈" hex head screws supplied in the Install the two #8-18 x 1³⁄₈" screws from the literature package in the literature package. Attach the handle. The handle should be top corners of the inner panel. Tighten the six side screws centered on the front of the customer-supplied custom panel in reinstalled in Step 6. the area shown. IMPORTANT: Screw heads must be flush with back of customer- Choose Attachment O
Streszczenie treści zawartej na stronie nr. 17
Option 2, Dishwasher side attachment: Move Dishwasher Close to Cabinet Opening NOTE: Remove the brackets from the parts package. WARNING Excessive Weight Hazard Use two or more people to move and install dishwasher. Failure to do so can result in back or other injury. Break off the end of the bracket along the scored line. With another person holding the rear of the dishwasher to keep it from tipping, open dishwasher door and place towel over pump assembly and spray arm of dishwasher. This
Streszczenie treści zawartej na stronie nr. 18
Check that water line is on the left side of opening and drain hose is near the center of the cabinet opening. When door is unlatched and door opens by itself, move the tensioner to a lower numbered hole and replace the screw. Reattach door spring to rear leg. NOTE: Tensioners on both sides of dishwasher should be secured at same holes. With another person holding the dishwasher to keep it from tipping, open and close the door a few times. If the door closes or falls open under its own we
Streszczenie treści zawartej na stronie nr. 19
Connect to Water Supply Check that leveling legs are firmly against the floor. Close and latch the door, and place level against the front panel. Check that dishwasher is centered from front to back in the opening. If Be sure rubber washer is properly seated in fitting. Slide the needed, adjust leveling leg until dishwasher is plumb. Repeat for ³⁄₄" fitting up to the valve and hand tighten to avoid cross- other side of dishwasher. threading. Hand tighten until the coupling is tight. Helpful
Streszczenie treści zawartej na stronie nr. 20
Connect to Drain Place towel under drain hose to catch any water in drain hose. Place the small green drain hose clamp onto the small end of the After hose is connected, remove towel. drain hose. Push the new drain hose into the black drain hose If needed, see website for animated representation of this step. connector up to the drain hose stop. Visit www.jenn-air.com/drain under FAQ tab. Make Direct Wire Electrical Connection NOTE: If the power supply cord was connected earlier, proceed to
