Streszczenie treści zawartej na stronie nr. 1
Electromagnetic Lock
E-941SA-600 600-lb. (272kg)
E-941SA-1200 1200-lb. (545kg)
With LED, Bond Sensor
E-941SA-600PQ 600-lb. (272kg)
E-941SA-1K2PQ 1200-lb. (545kg)
Weatherproof
E-941SA-300 300-lb. (136kg)*
Manual
*E-941SA-300
Streszczenie treści zawartej na stronie nr. 2
SECO-LARM ELECTROMAGNETIC LOCK Table of Contents: Introduction 2 Installation 4-6 Features 2 Wiring Diagram 7 Parts List 2 Maximum Wiring Distance 7 Specifications 2 Troubleshooting 8 Overview and Installation Applications
Streszczenie treści zawartej na stronie nr. 3
SECO-LARM ELECTROMAGNETIC LOCK Overview: Short self- tapping screws Armature screw Mounting plate Rubber washer Long self- tapping screws Guide pins Electromagnet Steel washers Armature plate Door spacer Hex-head mounting screws Sexnut bolt Tamper caps Installation Applications: NOTE: When mounting the electromagnet, it may be necessary to use a “Z”-bracket, 1 or 2 “L”-brackets, and/or plate spacers, depending on the location and the type of door and frame. Use the diag
Streszczenie treści zawartej na stronie nr. 4
SECO-LARM ELECTROMAGNETIC LOCK Ins tallation Notes: 1. Read this installation manual thoroughly. A clear understanding of the product and this manual will make installation much easier. 2. The electromagnetic lock is designed for indoor use ONLY. 3. The most suitable mounting location for the electromagnetic lock may require the use of additional SECO-LARM accessories such as Z-brackets, L-brackets, and/or spacer plates. Please see the diagram on page 3 to decide if a particular app
Streszczenie treści zawartej na stronie nr. 5
SECO-LARM ELECTROMAGNETIC LOCK 6. Depending on the type of door being protected, drill holes according to the diagrams below: Solid Core Door Hollow Metal Door Reinforced Door 5/8” (16mm) 5/16” (8mm) 1/4” (6.8mm) for M8x1.25 thread 1/2” (12 .7mm) 5/16” (8mm) Drill an 5/16” (8mm) dia. hole on the Drill a 5/16” (8mm) dia. hole through the Drill a 1/4” (6.8mm) door for the armature screw, and drill a dia. and 1” (25mm) armature-plate side of the door for the deep hole,
Streszczenie treści zawartej na stronie nr. 6
SECO-LARM ELECTROMAGNETIC LOCK 10. Once the position of the mounting plate is correct, 11. Drill the cable access hole. Run the power leads use the four long self-tapping screws to permanently through the cable access hole in the mounting plate mount the mounting plate. and through the hole in the door frame. Long self-tapping screws 13. Push the electromagnet against the mounting plate 12. Remove the cover from the front of the so the electromagnet ends are flush with t
Streszczenie treści zawartej na stronie nr. 7
SECO-LARM ELECTROMAGNETIC LOCK Wiring Diagram: Bond Status Sensor: The Bond Status Sensor checks to make sure the door is closed, (600PQ and 1K2P and the electromagnet is locked. models ONLY) LED Indicators: Green Door is closed and locked Red Door not closed and/or locked Off Door in use / No power 600PQ and 1K2P models ONLY Control Device* *NOTE: Connect switching devices like Voltage Selection Jumpers push-to-exit switches betwe
Streszczenie treści zawartej na stronie nr. 8
SECO-LARM ELECTROMAGNETIC LOCK Troubleshooting: Door does not lock Check to make sure the wires are securely tightened to the terminal block. Bond status LED does not Illuminate Check that the power supply is connected and operating. Use a meter to check the resistance of coils inside the lock. See below. Make sure the rubber washer is installed and free fr
