Streszczenie treści zawartej na stronie nr. 1
OPEN
LOCK
Network Camera
Network Operating Instructions
Model No. WV-NS202
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
WV-NS202
Streszczenie treści zawartej na stronie nr. 2
CONTENTS Preface ............................................................................................................................ 3 About these operating instructions .............................................................................. 3 Trademarks and Registered Trademarks ................................................................... 3 Viewer Software .......................................................................................................... 3 Monitor
Streszczenie treści zawartej na stronie nr. 3
Preface About these operating instructions There are 2 sets of operating instructions for the WV-NS202 as follows. • Installation Guide • Network operating instructions These network operating instructions contain descriptions of how to operate this product using a PC via a network and of how to configure the settings. Refer to the installation guide for descriptions of how to install this product and of how to connect to a network. ® ® Adobe Reader is required to read PDF. When the Adobe Reader
Streszczenie treści zawartej na stronie nr. 4
Monitor Images on a PC The following are descriptions of how to monitor images from the camera on a PC. Monitor images from a single camera Step 1 Notes: • When "ON" is selected for "User Authentication", the Start up the web browser. authentication window will be displayed before dis- Step 2 playing live images for the user name and password Enter the IP address designated using the Panasonic IP entries. The default user name and password are as setup software in the address box of the browser.
Streszczenie treści zawartej na stronie nr. 5
About the "Live" page !6 Full screen button !5 Alarm occurrence indication button !7 One shot button !4 Camera title !8 Mic input button !9 Audio output button q [Setup] button @0 SD recording status w [Live] button indicator e Multi-screen buttons r Image type buttons @1 Main area t Image capture size buttons y AUX buttons !2 BRIGHTNESS buttons u SD button !3 PRESET i Zoom buttons !0 AUTO MODE !1 Control pad/buttons o Focus buttons q [Setup] button (*1) : The letters "JPEG" on the button will
Streszczenie treści zawartej na stronie nr. 6
• When an object moves quickly u [SD] button (manual SD recording • When a moving object is too small or too big button) (*2) • When the shooting area is dark This button will be displayed only when "Manual" is • When there is a flicker in the shooting area selected for "Save trigger" on the setup menu. • When the zoom ratio is set to the TELE side, it ( page 22) may be difficult to obtain accuracy with the auto Click this button to manually record images on the tracking function. It is recom
Streszczenie treści zawartej na stronie nr. 7
In this case, the camera will not move when the !3 PRESET (*2) thumbnail image is clicked. (For example, when pre- Select a preset position from the pull-down menu set position 3 is unregistered, the thumbnail image and click the [GO] button. The camera will move to of preset position 2 will be displayed as the thumb- the selected preset position ( page 36). "H" next to nail image of preset position 3. The camera will not the preset position number indicates the home posi- move when the thumbna
Streszczenie treści zawartej na stronie nr. 8
Click a desired point in the main area on the "Live" !9 Audio output button (*3) page that is to be the center of the angle of view. Turns on/off the audio transmission (play audio from The camera moves to adjust the position in order to the PC on the camera speaker). This button will be set the clicked point as the center. Zoom can be displayed only when "Audio output" or "Interactive" is adjusted using the mouse wheel. selected for "Audio mode" on the setup menu. ( page 40) Note: The button
Streszczenie treści zawartej na stronie nr. 9
Monitor images from multiple cameras Images from multiple cameras can be displayed on a multi-screen. Images from 4 cameras (up to 16 cameras) can be displayed simultaneously. To display images on a multi-screen, it is necessary to register cameras in advance. 4 cameras can be registered as a group and up to 4 groups (16 cameras) can be registered. ( page 42) Important: • When simultaneously displaying images from 16 cameras on a multi-screen, panning, tilting and zooming are unavailable. • Onl
Streszczenie treści zawartej na stronie nr. 10
Record images on the SD memory card manually Images displayed on the "Live" page can be recorded on the SD memory card manually. This button is operable only when "Manual" is selected for "Save trigger" on the setup menu. ( page 22) Images recorded on the SD memory card can be copied onto the PC. ( page 24) Step 1 Step 4 Display the "Live" page. ( page 4) Click the [STOP] button to stop saving images on the SD memory card. Step 5 Click the [CLOSE] button to close the window. Step 2 Click the
Streszczenie treści zawartej na stronie nr. 11
Action at an Alarm Occurrence The alarm action will be performed when the following alarms occur. Alarm type Terminal alarm: When connecting an alarm device such as a sensor to the EXT I/O connector 1-3 on the rear of the camera, the alarm action (camera action at an alarm occurrence) will be performed when the connected alarm device is activated. Alarm action to be performed differs depending on the settings configured in the "Camera motion on alarm" section of the [Alarm] tab. ( page 44) VMD
Streszczenie treści zawartej na stronie nr. 12
Transmit images onto an FTP server Images can be transmitted to an FTP server. By configuring the following settings, transmission of images captured at an alarm occurrence or captured at a designated interval to an FTP server will become available. Important: • When using this function, set the user name and the password to access the FTP server to restrict users who can log into the FTP server. • To transmit images to the FTP server, select "Not use" for "SD memory card", or select "FTP error"
Streszczenie treści zawartej na stronie nr. 13
Save images on the SD memory card when images fail to transmit using the FTP periodic transmission function Images that have failed to transmit using the FTP periodic transmission can be saved automatically on the SD mem- ory card. Images saved on the SD memory card can be obtained from the [SD memory card] tab of the "Basic setup" page. ( page 22) To use the SD memory recording function featured in Panasonic’s network disk recorder, select "OFF" for "FTP peri- odic transmission" ( page 63) a
Streszczenie treści zawartej na stronie nr. 14
About the network security of the camera Equipped security functions The following security functions are featured in this camera. q Access restrictions by the host authentication and the user authentication It is possible to restrict users from accessing the camera by setting the host authentication and/or the user authentication to "ON". ( pages 54 and 55) w Access restrictions by changing the HTTP port It is possible to prevent illegal access such as port scanning, etc. by changing the HTTP
Streszczenie treści zawartej na stronie nr. 15
Display the setup menu and configure the settings of the camera using a PC The settings of the camera can be configured on the setup menu. The setup menu is only operable by users whose access level is "1. Administrator". How to display the setup menu Step 1 Display the "Live" page. ( page 4) Step 2 Click the [Setup] button on the "Live" page. → The window with the user name and password entry fields will be displayed. Step 3 Click the [OK] button after entering the user name and the passwor
Streszczenie treści zawartej na stronie nr. 16
How to operate the setup menu Important: When there are two or more [SET] buttons on the page, click the respective button to the edited setting item. A A-1 Menu button Setup page B Step 1 B-1 Click the desired button in the frame on the left of the window to display the respective setup menu. When completing the setting items in field A, click When there are tabs at the top of the setup page dis- the [SET] button below field A (A-1). The edited set- played in the frame on the right o
Streszczenie treści zawartej na stronie nr. 17
About the setup menu window !1 Status display area q [Live] button w [Basic setup] button e [Camera setup] button r [Multi-screen setup] button !2 Setup page t [Alarm setup] button y [Authentication setup] button u [Server setup] button i [Network setup] button o [Maintenance] button !0 [Help] button t [Alarm setup] button q [Live] button Click this button to display the "Alarm setup" page. Click this button to display the "Live" page. The settings relating to alarm occurrences such as settings
Streszczenie treści zawartej na stronie nr. 18
i [Network setup] button Click this button to display the "Network setup" page. The network settings and the settings relating to DDNS (Dynamic DNS), SNMP (Simple Network management Protocol) and the FTP (File Transfer Protocol) periodic transmission function can be con- figured on the "Network setup" page. Refer to page 58 for further information. o [Maintenance] button Click this button to display the "Maintenance" page. System log check, firmware upgrade and initializa- tion of the setup menu
Streszczenie treści zawartej na stronie nr. 19
Configure the basic settings of the camera [Basic setup] The basic settings such as time and date and camera name, and the settings relating to the NTP server and the SD memory card can be configured on the "Basic setup" page. The "Basic setup" page has 3 tabs; the [Basic] tab, the [NTP] tab and the [SD memory card] tab. Configure the basic settings [Basic] Click the [Basic] tab on the "Basic setup" page. ( page 15) The settings such as the camera name, time and date, etc. can be configured o
Streszczenie treści zawartej na stronie nr. 20
• SD memory card error LED: This LED will light [Alarm status port] when the SD memory card is unavailable to save When selecting "real time" for "Alarm status update images. mode", designate a port number to which the status • Power LED: This LED will light when the power is change notification is to be sent. on. Available port number: 1 - 65535 Default: 31004 [OSD Position] Select a position where time and date, camera title, pre- [Automatic installation of Viewer software] set ID, panning/til
