Streszczenie treści zawartej na stronie nr. 1
KTC-CBS24/CBH24
Bullet Camera
Streszczenie treści zawartej na stronie nr. 2
© 2003 GE Interlogix, Video Systems Group All Rights Reserved. Any GE Interlogix, Video Systems Group This equipment has been tested and software supplied with GE Interlogix, Video found to comply with the limits for a Systems Group products is proprietary and Class A digital device, pursuant to part furnished under license and can be used or 15 of the FCC Rules. These limits are copied only in accordance with the terms of designed to provide reasonable such license. protection ag
Streszczenie treści zawartej na stronie nr. 3
Bullet Camera User Manual Before You Begin BEFORE YOU BEGIN Read these instructions before installing or operating this product. Note: This installation should be made by a qualified service person and should conform to local codes. This manual provides installation and operation information. To use this document, you must have the following minimum qualifications: • A basic knowledge of CCTV systems and components • A basic knowledge of electrical wiring and low-voltage electrical h
Streszczenie treści zawartej na stronie nr. 4
Introduction Bullet Camera User Manual INTRODUCTION The standard- or high-resolution Bullet Camera includes a lens, a housing, a bracket, mounting fasteners, power and video cables, and a 24 VAC power supply. To install the unit, see Figure 1 and Figure 2 and perform the following. Upper screw hole LED illuminators Connector Camera lens Light sensor Bracket (attached to lower screw hole) Figure 1. Camera components Sunshield Sunshield screws (4) Figure 2. Sunshield components
Streszczenie treści zawartej na stronie nr. 5
Bullet Camera User Manual Installing the Bracket and Camera INSTALLING THE BRACKET AND CAMERA You can mount the camera on a vertical surface (Figure 3), and below (Figure 4) or above (Figure 5) a horizontal surface. Figure 3. Mounting on a vertical surface Figure 4. Mounting below a horizontal surface Figure 5. Mounting above a horizontal surface 1043349A / September 2003 5
Streszczenie treści zawartej na stronie nr. 6
Installing the Bracket and Camera Bullet Camera User Manual CHOOSING AN INSTALLATION LOCATION Consider the field of view for the camera and the range of the LED illuminators when you select an installation location. • The LED illuminators are effective in nighttime conditions to approximately 33 feet (10.1 m). • See Table 1 for field of view information. Table 1. Example approximate fields of view Distance from camera Horizontal Vertical 4 ft (1.2 m) x 3 ft (0.9 m) 5 ft (1.5 m) 8
Streszczenie treści zawartej na stronie nr. 7
Bullet Camera User Manual Installing the Bracket and Camera 4) Attach the mounting plate to the mounting surface as shown in Figure 7. 5) Reinstall the top of the bracket onto the mounting plate and tighten the wing nut as shown in Figure 8. Figure 7. Attaching the mounting Figure 8. Mounted bracket plate to the mounting surface 1043349A / September 2003 7
Streszczenie treści zawartej na stronie nr. 8
Installing the Bracket and Camera Bullet Camera User Manual ATTACHING THE CAMERA TO THE BRACKET See Figure 9 and perform the following. Figure 9. Attaching the camera to the bracket 1) Loosen the wing nut to free the ball and socket bolt. 2) Slide the camera’s upper or lower screw hole onto the bolt. 3) Twist the ball and socket bolt into the camera screw hole. 4) Use the nut to secure the camera onto the bolt. 5) Tighten the wing nut. 8 1043349A / September 2003
Streszczenie treści zawartej na stronie nr. 9
Bullet Camera User Manual Installing the Bracket and Camera ADJUSTING THE CAMERA ANGLE See Figure 10 and perform the following. Figure 10. Adjusting the camera angle 1) Loosen the wing nut. 2) Swivel the camera on the ball and socket bolt to achieve the proper angle. 3) Tighten the wing nut to secure the camera in position. 1043349A / September 2003 9
Streszczenie treści zawartej na stronie nr. 10
Installing the Bracket and Camera Bullet Camera User Manual INSTALLING THE SUNSHIELD Install the sunshield to protect the camera from rain and to minimize heat build-up from sun exposure. To install the sunshield, see Figure 11 and perform the following. Note: For interior installations, the sunshield might not be necessary. Figure 11. Installing the sunshield 1) Slide the sunshield into the desired position on the camera. 2) Tighten the sunshield screws (4) on both sides of the suns
Streszczenie treści zawartej na stronie nr. 11
Bullet Camera User Manual Making Cable Connections MAKING CABLE CONNECTIONS See Figure 12 and perform the following. Cable To camera receptacle Cable plug Camera setting controls cover Video out Power in Figure 12. Cable connections 1) Connect the camera’s cable receptacle to the cable plug. 2) Connect the video out connector to the video input on the monitor. 3) Connect the power in connector to the 24 VAC power supply. 4) Supply power to the unit. 1043349A / September 2003
Streszczenie treści zawartej na stronie nr. 12
Installing the Bracket and Camera Bullet Camera User Manual ADJUSTING CAMERA SETTINGS To adjust backlight compensation and vertical phase, on the 24 VAC Phase control power supply open the camera buttons setting controls cover (see – + Figure 12). BACKLIGHT COMPENSATION Backlight compensation controls iris gain and white balance simultaneously. If you have objects in the foreground that appear silhouetted in front of a brighter Backlight compensation jumper background, set
Streszczenie treści zawartej na stronie nr. 13
Streszczenie treści zawartej na stronie nr. 14
Streszczenie treści zawartej na stronie nr. 15
Streszczenie treści zawartej na stronie nr. 16
Mfg. # 98230006
