Streszczenie treści zawartej na stronie nr. 1
CCD B/W CAMERA MODULE
XC-ES50/50CE
XC-ES30/30CE
XC-EI50/50CE
XC-EI30/30CE
User’s
Guide
(Ver. 1.0) — English —
Streszczenie treści zawartej na stronie nr. 2
XC-E series Table of Contents OUTLINE ................................................................................................................. 1 MAIN FEATURES .................................................................................................... 1 SYSTEM CONFIGURATION ................................................................................... 2 SPECIFICATIONS COMPARISON .......................................................................... 2 MAIN SPECIFICATIONS
Streszczenie treści zawartej na stronie nr. 3
XC-E series OUTLINE The XC-ES30/30CE, XC-ES50/50CE, XC-EI30/30CE, and XC-EI50/50CE are industrial black-and-white video camera modules, each using a 1/3- or 1/2-inch IT CCD. The 1/3- and 1/2-inch C mount commonly used in industrial applications implements compact size and lightweight. Switching of each mode on the rear panel, which has been installed from the XC-ST series, is followed to provide improved operability. The XC-EI series uses a CCD which is sensitive on a near infrared area to ca
Streszczenie treści zawartej na stronie nr. 4
XC-E series SYSTEM CONFIGURATION The components making up the system based on XC-E series video camera are as follows. Video camera module Camera cables Camera adaptor XC-ES50/50CE CCXC-12P02N (2 m) DC-700/700CE XC-ES30/30CE CCXC-12P05N (5 m) XC-EI50/50CE CCXC-12P10N (10 m) XC-EI30/30CE CCXC-12P25N (25 m) Junction box Tripod adaptor C-mount lenses Close-up ring kit JB-77 VCT-333I (Isolated type) VCL-08YM LO-77ERK VCL-12YM VCL-16Y-M VCL-25Y-M VCL-50Y-M SPECIFICATIONS COMPARISON XC-ST50 XC-ES50 XC
Streszczenie treści zawartej na stronie nr. 5
XC-E series MAIN SPECIFICATIONS Image pickup device Sensitivity XC-ES50/50CE, XC-EI50/50CE: XC-ES50/50CE: 400 lx F5,6 (γ =ON, MIN Gain, 1/2-inch interline transfer CCD without IR cut filter) XC-ES30/30CE, XC-EI30/30CE: XC-ES30/30CE: 400 lx F4 (γ =ON, MIN Gain, 1/3-inch interline transfer CCD without IR cut filter) Number of effective pixels XC-EI50/50CE: 400 lx F11 (γ =OFF, MIN Gain, XC-ES50/EI50, XC-ES30/EI30: without IR cut filter) 768 (H)x494 (V) XC-EI30/30CE: 400 lx F8 (γ =ON, MIN Gain, XC-E
Streszczenie treści zawartej na stronie nr. 6
XC-E series MAIN SPECIFICATIONS Shock resistance 70G External synchronization for each mode Outside dimensions 29 (W) x 29 (H) x 32 (D) mm External sync Mode Internal sync Weight 50 g HD/VD VS Standards UL1492, FCC Class A Digital Normal Device, and CE (EN50081-2 + Normal shutter EN50082-2) Other Restart Reset function Mode 1 × Frame or field integration can be selected. Trigger signal Conforms to new EIAJ and uses generates an Mode 2 × × internal VD 12-pin assignment. (single) signal. Acces
Streszczenie treści zawartej na stronie nr. 7
XC-E series LOCATION OF PARTS AND OPERATION XC-ES50/50CE . XC-ES30/30CE 1 Lens mount section (C mount) A commercial C-mount lens as well as a XC-EI50/50CE . XC-EI30/30CE Sony standard lens can be used. 2 2 Camera mounting reference hole (top) These screw holes are positionned with high precision related to CCD sensor. 4 3 Camera mounting reference 1 hole/Screw hole for tripod adaptor mounting (bottom) 4 12-pin multi-connector DC IN/HD/VD (DC power/sync signal input) VIDEO OUT terminal 23 3 5 75
Streszczenie treści zawartej na stronie nr. 8
XC-E series PHASE CONDITIONS OF EXTERNAL SYNCHRONIZATION External synchronization for each mode • For normal video/normal shutter Continuous HD/VD signal (should conform to EIA and CCIR frequencies in the timing shown in the figure below.) • For Restart Reset (RR)/external trigger shutter Continuous HD signal. The phase between VD (reset) and HD signals is as specified in the figure below in any timing. Phase conditions The phase relation between external input HD and VD signals should be set a
Streszczenie treści zawartej na stronie nr. 9
XC-E series ELECTRONIC SHUTTER Two types of electronic shutter are provided “normal shutter and external trigger shutter”. The electronic shutter speed and type can be set using the DIP switch on the rear panel. DIP switch on the rear panel Rear panel DIP switch Switches 1 to 4: Selects the shutter speed. Switch 5: Selects the frame (0) or (1) field integration. Switches 6 to 8: Select the trigger shutter mode. Switch: γ Selects correction ON/OFF Switches 0: Selects the Gain (Ma
Streszczenie treści zawartej na stronie nr. 10
XC-E series ELECTRONIC SHUTTER External trigger shutter These modes are used to capture one image (one field) per trigger pulse. Set DIP switches 6, 7, and 8 on the rear panel to mode 1 or 2. (Refer to the table below.) When the trigger pulse width is 1/3 sec or more, the output signal is switched to a normal video signal. There are two modes for timing in which a video signal is obtained. • Mode 1 (Non-reset mode) In this mode, a video signal synchronized with a VD signal is output after a trig
Streszczenie treści zawartej na stronie nr. 11
XC-E series ELECTRONIC SHUTTER • Using trigger pulse width • Set DIP switches 1 to 4 on the rear panel to 0. • An arbitrary shutter speed can be obtained by setting the trigger pulse width to the range of 2 μsec to 250 msec. Mode 1 Mode 2 Switch Exposure time = Trigger pulse width + 97 μsec (EIA) (Non-reset mode) (Reset mode) 0 0 120 μsec (CCIR) 1 2 0 0 : 1. lt is recommended to set DIP switch 5 for field selection. Note 0 0 3 (The field selection is about two times in sensitivity as high as
Streszczenie treści zawartej na stronie nr. 12
XC-E series ELECTRONIC SHUTTER When using a trigger pulse like shown below, set the TRIG polarity selector switch on the rear panel to – : A B T A: 4.0 to 5.0 V B: 0 to 2.0 V T: 2 μs to 1/4 s, 100 μs to 1/4 s when setting the shutter speed using DIP switch Input impedance: 10 kΩ or more * The voltage and pulse width used are measured at pin 11 of a 12-pin multi-connector on the rear panel. * Specifications of WEN (Write ENable Pulse) A B T A: 5.0 V B: 0 V T: 15.875 ms (XC-ST70), 18.752 ms (X
Streszczenie treści zawartej na stronie nr. 13
XC-E series RESTART RESET (R.R) The information on one screen can be extracted at any time by inputting a restart/reset signal (HD/VD) from the outside. To enter this mode, set DIP switches 6, 7, and 8 on the rear panel of a camera as shown in the table below. The setting is especially effective for the following operation. Switch Restart Reset (R.R) 1 0 0 2 3 0 0 4 5 0 1 6 7 1 1 8 9 0 1: ON 0 0 0: OFF Long exposure A high-sensitivity image is obtained by extending the exposure time of the CCD
Streszczenie treści zawartej na stronie nr. 14
XC-E series RESTART RESET (R.R) Example 2 of long exposure EXT HD Continuous signal: 15.734 kHz (XC-ES50/ES30, XC-EI50/XC-EI30) Allowable frequency value – 1%, 15.625 kHz (XC-ES50CE/ES30CE, XC-EI50CE/XC-EI30CE) Allowable frequency value – 1% EXT VD VD interval(T): 262.5H or more (XC-ES50/ES30, XC-EI50/XC-EI30) and less than 1 second (Recommended), 312.5H or more (XC-ES50CE/ES30CE, XC-EI50CE/XC-EI30CE) and less than 1 second (Recommended) Four or more VD pulses are required
Streszczenie treści zawartej na stronie nr. 15
XC-E series FRAME IMAGE OUTPUT WITH STROBE LIGHT A full frame image with vertical resolution of 485 lines (XC-ST70) or 575 lines (XC-ST70CE) can be obtained with a strobe light by firing the strobe when the exposure time of the two fields overlap. • Timing and conditions EXT HD Continuous signal: 15.734 kHz (XC-ES50/ES30, XC-EI50/XC-EI30)Allowable frequency value – 1%, 15.625 kHz (XC-ES50CE/ES30CE, XC-EI50CE/XC-EI30CE) Allowable frequency value – 1%
Streszczenie treści zawartej na stronie nr. 16
494 492 490 493 491 489 494 XC-E series (XC-ES50/EI50/ES30/EI30(EIA)) OUTPUT WAVEFORM TIMING CHART Timing chart of horizontal output waveform HD 91 (6.36 μs) 40 77 22 3 15 752 CCD output signal Effective total pixel 768 Dummy 69.8 ns pixel Optical black portion Horizontal transfer stop period Optical black portion Horizontal blanking period (11.0 μs) Output video period Camera video output signal (Typical value) 67 (4.68 μs) 752 (52.5 μs) 21 HSYNC (1.47 μs) 70 (4.89 μs) One horizontal scan
Streszczenie treści zawartej na stronie nr. 17
493+494 491+492 489+490 7+8 5+6 3+4 1+2 494 492+493 490+491 488+489 8+9 6+7 4+5 2+3 1 XC-E series ELECTR OUTPUT ONIC SHUTTER WAVEFORM TIMING CHART (XC-ES50/EI50/ES30/EI30(EIA)) Timing chart of vertical output waveform (2:1 interlaced field integration) Odd field (262.5 H) Even field (262.5 H) VD 9 H 253.5 H 9 H 253.5 H CCD output signal 1 8 6 4 242.5 1 8 6 3.5 242.5 Empty Empty transfer transfer Camera Optical black portion Optical black portion video output signal Vertical blanking Vertical bl
Streszczenie treści zawartej na stronie nr. 18
582 580 581 579 XC-E series OUTPUT WAVEFORM TIMING CHART (XC-ES50CE/EI50CE/ES30CE/EI30CE (CCIR)) Timing chart of horizontal output waveform HD 98 (6.91 μs) 40 91 22 3 15 736 CCD output signal Effective total pixel 752 Dummy 70.5 ns Optical black pixel portion Horizontal transfer stop period Optical black portion Horizontal blanking period (12.1 μs) Output video period Camera video output signal (Typical value) 81 (5.71 μs) 736 (51.9 μs) 21 HSYNC (1.48 μs) 70 (4.93 μs) One horizontal scanning
Streszczenie treści zawartej na stronie nr. 19
581+582 579+580 7+8 5+6 3+4 1+2 582 580+581 578+579 8+9 6+7 4+5 2+3 1 XC-E series OUTPUT ELECTRONIC SHUTTER WAVEFORM TIMING CHART (XC-ES50CE/EI50CE/ES30CE/EI30CE (CCIR)) Timing chart of vertical output waveform (2:1 interlaced field integration) Odd field (312.5 H) Even field (312.5 H) VD 7.5 H 305 H 7.5 H 305 H CCD output signal 287.5 287.5 1 14 6 3.5 1 14 6 3 Empty Empty transfer transfer Camera Optical black portion Optical black portion video output signal Vertical blanking Vertical blankin
Streszczenie treści zawartej na stronie nr. 20
XC-E series SENSOR READ CLOCK TIMING CHART XC-ES30 HD V1 2.5 V2 Odd Field V3 V4 1.6 2.5 2.5 2.5 40.4 0.2 V1 V2 Even Field V3 V4 Unit : μs XC-ES30CE HD V1 2.5 V2 Odd Field V3 V4 1.6 2.5 2.5 2.5 41.6 0.2 V1 V2 Even Field V3 V4 Unit : μs 18
