Streszczenie treści zawartej na stronie nr. 1
FT920
19” Flat CRT
User’s
Manual
By Envision Peripherals, Inc.
www.aocmonitor.com
Streszczenie treści zawartej na stronie nr. 2
Thank you very much for choosing the AOC Color Monitor. We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor. Please keep this manual in a safe place for your future reference. Plug & Play Drivers for the AOC Series Monitors are available at: www.aocmonitor.com CHECKING THE CONTENTS OF THE MONITOR PACKAGE The product package should include the following items: 1. Monitor 2. Ow
Streszczenie treści zawartej na stronie nr. 3
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may caus
Streszczenie treści zawartej na stronie nr. 4
PRECAUTIONS Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit ins
Streszczenie treści zawartej na stronie nr. 5
Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC1 and DDC2B. The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information. The DDC2B is a
Streszczenie treści zawartej na stronie nr. 6
TECHNICAL SUPPORT(FAQ) Power LED is not on *Power Cord should be connected No Plug & Play *Check if the PC System is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent *Make sure the AOC Monitor Drivers are installed (AOC Monitor Drivers are available at: www.aocmonitor.com) Picture is fuzzy *Adjust the Contrast and Brightness Controls. Picture bounces or a wave pattern is present in the picture *Move elect
Streszczenie treści zawartej na stronie nr. 7
INSTALLATION INSTRUCTIONS SWIVEL BASE To attach the swivel base to the monitor, do the following: • Carefully turn the monitor on its side or upside down. (see figure 1) • Locate the cavities at the bottom front of the monitor. • Insert the pegs on the swivel base into these cavities. Push the swivel base forward until the swivel base locks in place. • To remove the swivel base, hold the bottom of the swivel base, then push it out. POWER CORD Power Source: 1. Make sure the po
Streszczenie treści zawartej na stronie nr. 8
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS The other control knobs are located at the base of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the video cable from the monitor to the video card. • To turn the monitor on, press the power switch to ON position. The power indicator will light up. • Your monitor features a unique quick switch system which provides a pictur
Streszczenie treści zawartej na stronie nr. 9
Figure 1: Installing and Removing the Swivel Base Figure 2: Connecting Cables 1. Power Cord 2. Signal Cable 3. VGA Card Connector Figure 3: External Controls 1. Shuttle Knob 2. Power Indicator 3. Standby Switch 2 1 3 Figure 4: The OSD Menu 1024 × 768
Streszczenie treści zawartej na stronie nr. 10
FRONT PANEL CONTROL (see figure 3) NT PANEL CONTROL • Standby Switch: When pressed, the monitor enters the off mode, and the LED turns orange. Press again and hold to restore normal status. • Power Indicator : Green — Power On mode. Orange — Off mode. • Shuttle Knob : The Shuttle Knob is used to control the monitor functions. Rotate to switch functions or adjust settings. Press to select or execute a function. HOW TO ADJUST A SETTING 1. Press the Shuttle Knob
Streszczenie treści zawartej na stronie nr. 11
ADJUSTING THE PICTURE (see figure 4) 1. CONTRAST Adjust the picture contrast. 2. BRIGHTNESS Adjust the picture brightness. 3. H- CENTER Adjust the horizontal position of the picture. 4. H- SIZE Adjust the picture’s horizontal size. 5. V- CENTER Adjust the vertical position of the picture. 6. V- SIZE Adjust the picture’s vertical size. Adjust the picture’s horizontal and vertical size 7. ZOOM simultaneously. 8. PINCUSHION Adjust the pincushion and barrel.
Streszczenie treści zawartej na stronie nr. 12
SPECIFICATION CRT 48.3cm(19"), 90º deflection, 29mm neck, 21mm(H), 0.25mm(D) dot pitch Viewable Image Size 45.7cm (18"), diagonal Video 0.7Vpp, R, G, B Analog Separate Sync. TTL Level H/V-sync.: Positive/Negative Scanning Frequency: Horizontal 30kHz to 98kHz automatically Vertical 50Hz to 160Hz automatically Max. Resolution 1600 × 1200 Video Dot Rate 200MHz Factory Preset 8 Timings : User mode Timings : 20 Power Source Universal AC 100-240V, 50Hz/60Hz Operating 0°C to 4
Streszczenie treści zawartej na stronie nr. 13
Preset Timing Table STANDARD RESOLUTION HORIZONTAL VERTICAL FREQUENCY FREQUENCY IBM 720 x 400 31.5kHz 70Hz VGA 640 x 480 31.5kHz 60Hz VESA/85 640 x 480 43.3kHz 85Hz VESA/85 800 x 600 53.7kHz 85Hz VESA/85 1024 x 768 68.7kHz 85Hz VESA/85 1280 x 960 85.9kHz 85Hz VESA/85 1280 x 1024 91.1kHz 85Hz VESA/75 1600 x 1200 93.8kHz 75Hz Connector Pin Assignment 15 6 10 11 15 PIN NO. PIN NO. DESCRIPTIO NO. de DESCRIPTI N ON Terminal PIN NO. 1. Video-Red 9. 5V 2. Video-Green 10. GND
