Skullcandy CRUSHER-EVO user manual

If your Skullcandy Crusher Evo headphones are flashing red, it could indicate one of the following issues:
1. Low Battery: When the battery level is critically low, the Crusher Evo headphones will flash red to indicate the need for charging. Plug in the headphones using the included USB-C cable and charge until the LED stops flashing.
2. Firmware Update: If the headphones are flashing red intermittently, it might be due to a pending firmware update. Make sure your headphones are connected to the Skullcandy app and check for any available updates. If an update is available, follow the instructions to complete the update.
3. System Error: Occasionally, the Crusher Evo headphones might encounter a system error that causes the red LED flashing. In such cases, it is recommended to perform a hard reset. To reset the headphones, simply hold the power button and the volume up (+) button simultaneously for 10 seconds until the LED turns white. After the reset, you can try using them again.
If none of these solutions resolve the red LED flashing issue, it's advisable to reach out to Skullcandy support for further assistance.

To check the battery level of your Skullcandy Crusher Evo headphones, you can follow these steps:
1. Ensure that your headphones are powered on.
. Press and hold the "+" (volume up) and "-" (volume down) buttons simultaneously for about 3 seconds until you hear a voice prompt saying "Battery high," "Battery medium," or "Battery low."
3. The voice prompt will indicate the current level of battery charge in your headphones.
Alternatively, you can also use the Skullcandy app (available for iOS and Android) to check the battery level and manage other features of your Crusher Evo headphones.

To set up your Skullcandy Crusher Evo headphones, follow the steps below:
1. Power on: Press and hold the power button on the left earcup for about 5 seconds to turn on the headphones. You will hear an audible voice prompt once they power on.
2. Pairing mode: After powering on, the headphones will automatically enter pairing mode. The LED indicator on the right earcup will flash blue and red. If you want to manually enter pairing mode, press and hold the volume up and volume down buttons simultaneously for 3 seconds until the LED starts flashing blue and red.
3. Connect to a device: Open the Bluetooth settings on your audio source device (e.g., smartphone, tablet, etc.) and search for available devices. Look for "Crusher Evo" on the list and select it to connect. Once connected, you will hear an audible voice prompt saying "Connected."
4. Personal sound customization: Download and install the Skullcandy App from your device's app store. Open the app and follow the on-screen instructions to personalize your audio experience using the Personal Sound feature.
5. Bass and haptic feedback controls: On the left earcup, you'll find the bass slider that allows you to adjust the level of bass according to your preference. Additionally, the haptic feedback slider on the left earcup lets you adjust the intensity of the haptic bass feedback.
6. Music controls: Use the small buttons located on the rear side of the left earcup for music playback controls. The central button can be used to play/pause music or answer/end calls, while the volume up and volume down buttons allow you to adjust the volume.
7. Active Noise Cancellation (ANC): To activate ANC mode, press and hold the central button on the left earcup for about 2 seconds. You will hear a voice prompt saying "ANC on." Repeat the same step to turn off ANC.
These are the basic setup instructions for Skullcandy Crusher Evo headphones. Remember to refer to the user manual provided with the product for more detailed information on specific features and functionalities.

If your Skullcandy Crusher-Evo headphones are flashing blue and red, it typically indicates that they are in pairing mode. This means that the headphones are ready to be connected to a new Bluetooth device. You can follow the steps below to pair your headphones:
1. Make sure your headphones are powered off.
. Press and hold the power button until you see the LED light flashing blue and red.
3. On your desired Bluetooth device (phone, tablet, etc.), go to the Bluetooth settings and make sure it is in pairing mode as well.
4. Scan for Bluetooth devices and select "Crusher-Evo" from the list.
5. Once the headphone successfully connects, the LED light should turn solid blue.
If you have already paired your headphones and they are still flashing blue and red, it could indicate that the headphones are in a different mode. In this case, you can try resetting your headphones by following these steps:
1. Power off your headphones.
. Press and hold the volume up (+) and volume down (-) buttons simultaneously for about 10 seconds.
3. The LED light should flash red and blue, indicating that the headphones have been reset.
4. Power them back on and try pairing them with your device again.
If you are still experiencing issues with your Skullcandy Crusher-Evo headphones flashing blue and red, it may be best to consult Skullcandy support or refer to the user manual for further assistance.