Sage MACHINE-A-CAFE user manual

There could be a few potential reasons why your Sage coffee machine is not getting up to pressure:
1. Blocked or dirty filters: If the coffee grounds or minerals from the water have built up to an extent where they are blocking the filter, the pressure will not build correctly. You should clean or replace the filter as recommended in your user manual.
2. Incorrectly ground coffee: The coffee grounds should be fine enough that water cannot pass through them too quickly, but not so fine that they clog up the machine. Experiment with different grind sizes to see if this resolves the issue.
3. Water tank is not connected properly: Ensure that the water tank is securely attached and that the valve is open.
4. Insufficient water: If there is too little water in the tank, the machine will not be able to build up enough pressure.
5. Pump malfunction: Coffee machines use a pump to force water at the correct pressure through the coffee grounds. If the pump is not working correctly, the pressure will be too low. You may need a technician to fix this.
6. Scale build-up: Over time, limescale can accumulate in your machine, especially if you live in a hard water area. This can prevent water from flowing freely and creating the necessary pressure. Use a safe decalcifying agent to clean your coffee machine.
Always remember to check with a professional or contact Sage support before attempting any self-repairs on your machine.

Using a Sage coffee maker is quite simple and straightforward. Here's a basic step-by-step guide on how to do it:
1. Plug in your Sage coffee maker to a power outlet.
2. Fill the water tank: Remove the water tank, refill it with fresh, cold water and replace it back on the machine.
3. Place the coffee: Next, select your coffee type (bean or pre-ground) and put it into the portafilter. Use the appropriate filter for either single or double shots.
4. Tamp the coffee: Place the coffee-filled portafilter in the included tamper and apply pressure to compact the grounds. Ensure you do this evenly to achieve balanced extraction.
5. Attach the portafilter: Attach the portafilter to the machine, making sure it's secure and locked in place.
6. Preheat your cup: Run an empty shot to pre-warm your cup. This step ensures your coffee stays hot for longer.
7. Extract the coffee: Place your pre-warmed cup underneath the portafilter and press the extraction button (either single or double shot, depending on your preference).
8. Froth milk: If your drink requires frothed milk, pour cold milk into a jug and steam it using the steam wand. Ensure to clean the steam wand after every use.
9. Prepare your coffee drink: After your coffee is extracted and your milk is frothed, you can make your preferred coffee drink whether cappuccino, latte, etc.
10. Clean up after use: After every use, clean your Sage coffee maker to ensure it operates at its best. Rinse the portafilter, empty the drip tray, and wipe down the machine with a damp cloth.
Remember, the procedures might slightly vary depending on the model of your Sage coffee maker. Be sure to read and understand your machine's manual for detailed instructions.

To reset your Sage coffee machine, follow these steps:
1. Ensure that the coffee machine is turned off and disconnected from the power supply.
2. Locate the power button or switch, usually found on the front or side of the machine.
3. Press and hold down the power button or switch for about 10 seconds.
4. While still holding the power button down, connect the machine back to the power supply.
5. Continue holding the power button for another 10 seconds.
6. Release the power button and wait for a few seconds.
7. Turn on the machine by pressing the power button once.
8. The Sage coffee machine should now be reset to its default settings.
Note: The specific reset instructions may vary depending on the model of your Sage coffee machine. It's recommended to consult the instruction manual or contact the manufacturer's customer support for detailed instructions tailored to your machine model.

The frequency of changing the water filter on a Sage coffee machine may vary depending on factors such as the quality of the water used and the amount of usage. However, it is generally recommended to change the water filter every 2-3 months or after making approximately 60 liters (or 16 gallons) of coffee. Regularly replacing the water filter ensures that it continues to effectively remove impurities and maintain the taste and quality of your coffee. It is important to follow the manufacturer's instructions for your specific model to ensure optimal performance.