One for All REMOTE-CONTROLLERS user manual

To reset a One For All remote control, follow these steps:
1. Turn on the device you want to control with the remote.
. Press and hold the Magic button and the device button (e.g., TV, DVD, AUX) simultaneously for three seconds until the LED light on the remote stays on.
3. While still holding the Magic and device buttons, enter the code "981" using the numeric keypad on the remote.
4. Release both buttons. The LED light should blink twice, indicating the reset was successful.
5. Now, reprogram the remote control by entering the correct code for your device or by using the auto-search method.
Note: If the LED light doesn't blink twice, repeat the steps above and make sure you're holding down the buttons properly. Also, if you performed a reset on the One For All remote, any previously programmed codes will be erased, and you will need to reprogram them.

To program your One For All remote control, follow the steps below:
1. Turn on the device you want to control with the remote (e.g., TV, DVD player, audio system).
2. Press and hold down the "Magic" or "SETUP" button on your remote control until the indicator light stays on.
3. Enter the provided 4-digit setup code for your specific device using the number buttons on the remote control. You can find the codes in the manual that came with your remote or on the One For All website.
4. Once you have entered the correct 4-digit code, the indicator light on the remote control will blink and turn off.
5. Point the remote control towards the device you want to control and press the power button. If the device turns off, you have successfully programmed your remote. If not, repeat steps 2-5 with a different setup code until the device responds.
6. After programming, press the "Magic" or "SETUP" button again to save the code.
If your specific device's setup code is not available or you are unable to find it, you can try the manual code search method. Here's how:
1. Turn on the device you want to control.
2. Press and hold the "Magic" or "SETUP" button until the indicator light stays on.
3. Press the "Power" (or equivalent) button repeatedly while pointing the remote control towards the device. Keep pressing until the device turns off.
4. As soon as the device turns off, press the "Magic" or "SETUP" button again to save the code.
Remember, these instructions are general guidelines, and the exact process may vary depending on the model of your One For All remote control. Refer to the user manual or manufacturer's website for specific instructions for your remote control model.

Programming a One For All remote without codes can be a bit tricky, as the remote usually requires specific codes to be programmed correctly. However, there are a few general methods you can try:
1. Auto Search: This method allows the remote to search for the correct code by cycling through all possible codes until it finds the right one. Here's how to do it:
a. Turn on the device you want to control with the remote.
b. Press and hold the "Setup" button on the remote until the LED light stays on.
c. Enter the code "9-9-1" using the number keys.
d. Aim the remote at the device and press the "Power" button.
e. Keep pressing the "Power" button every few seconds until the device turns off.
f. Once the device turns off, press the "Enter" button on the remote to save the code.
2. Manual Search: If the auto search method does not work, you can try the manual search method, which involves cycling through every code manually. Here's how:
a. Turn on the device you want to control with the remote.
b. Press and hold the "Setup" button on the remote until the LED light stays on.
c. Enter the code "9-9-0" using the number keys.
d. Use the number keys to manually enter each code, one by one, starting from 0001.
e. After entering each code, try pressing the "Power" button to see if the device turns off.
f. Keep cycling through the codes until you find the one that turns off the device.
g. Once the device turns off, press the "Enter" button on the remote to save the code.
Note that these methods may not always work as intended, especially if the remote requires specific codes. In such cases, it is advisable to refer to the instruction manual or contact the manufacturer for further assistance.

The "magic" button on a One For All remote control refers to the "Magic" or "Magic Key" button. This button is typically labeled with a symbol of a wand or magic hat. The purpose of the magic button varies depending on the specific model and the devices you are controlling. It is designed to simplify the operation of multiple devices simultaneously. By pressing the magic button, you can set the remote control to control multiple devices (e.g., TV, DVD player, sound system) with a single button press.