NETGEAR EX3800 user manual

To log into your Netgear EX3800 Wi-Fi range extender, follow these steps:
1. Connect your device to the Netgear extender's Wi-Fi Network. The default network name should be "NETGEAR_EXT".
2. Open an Internet browser from a computer or wireless device that is connected to the Netgear extender’s network.
3. Type in "www.mywifiext.net" or "192.168.1.250" in your web browser's address bar and press Enter.
4. The Netgear extender login window appears on your screen.
5. Enter your username and password. The default login details are:
Username: admin

Password: password

6. Click or tap "Log In".
7. You are now logged in and can change settings as per your preference.
Note: The steps could slightly vary depending on the model or firmware version you're using. Also, if you've previously changed the admin login details of your extender and forgotten them, you might need to reset your device back to the default settings.

There could be several reasons why your Netgear Wi-Fi extender is not working. Here are a few possible causes and troubleshooting steps you can try:
1. Incorrect setup or configuration: Make sure that you have properly set up and configured your Wi-Fi extender by following the manufacturer's instructions. Double-check that you have connected it to your existing home Wi-Fi network correctly.
2. Poor signal strength: Place your Wi-Fi extender in a location where it can receive a strong wireless signal from your router. Avoid placing it too far away from the router or in areas with interference such as thick walls, metal objects, or electronic devices. You may need to experiment with different placement options for optimal signal strength.
3. Incorrect network settings: Ensure that you have correctly entered the network name (SSID) and password for your existing Wi-Fi network during the setup process. Incorrect or mismatched settings can prevent the extender from connecting.
4. Firmware issues: Check if there are any available firmware updates for your Wi-Fi extender. Outdated firmware can cause compatibility and performance issues. Visit the Netgear website and download the latest firmware for your specific model, then follow the instructions provided to update it.
5. Reset the extender: If you have tried everything else and still can't get the extender to work, try performing a factory reset. Look for a small reset button or hole on the device and use a paperclip or pin to press and hold it for about 10 seconds. This will restore the extender to its default settings, allowing you to start the setup process again from scratch.
If none of these steps resolve the issue, consider contacting Netgear's technical support for further assistance.

To reconnect your Netgear extender to your network, follow the steps below:
1. Place your extender in the same room as your router for the initial setup. Once the setup process is complete, you can move it to its desired location.
2. Make sure your extender is plugged into a power outlet and the power LED on the extender is lit.
3. Connect your computer or mobile device to the extender's network. You can find the default network name (SSID) and password (network key) on the product label of your extender.
4. Open a web browser on your connected device and enter http://www.mywifiext.net or http://192.168.1.250 in the address bar. Press Enter.
5. You will be prompted to log in. Enter the admin username and password. The default username is admin, and the default password is password. If you have changed these settings before, enter your custom login credentials.
6. Once logged in, the Netgear Genie setup wizard will appear. Follow the on-screen instructions to connect your extender to your existing Wi-Fi network.
7. You will be prompted to select your network from the list of available networks. Select your network and enter the network password if required. Click on the Next button to continue.
8. After entering the network password, click on the Continue button. The extender will now attempt to connect to your existing Wi-Fi network.
9. Once the extender is connected to your network, you can set up a new network name (SSID) and password for the extender's extended network. You can also choose to use the same network name and password as your existing network.
10. After completing the setup process, the extender will reboot. Once it has rebooted, disconnect your device from the extender's network and connect it back to your main Wi-Fi network.
11. You can now move the extender to its desired location. Ensure that it is within range of your router for optimal performance.
That's it! Your Netgear extender should now be reconnected to your network.