Lexmark MB2236ADW user manual

1. On the main screen of your Lexmark mb2236adw printer, press "Settings" or "Menu".
2. Then navigate to "Device" or "System Settings" and press "OK".
3. You will see an option labeled "Reset" or "Factory Reset". Select this option then press "OK".
4. A message will appear asking you if you are sure, select "Yes" then press "OK".
5. Your printer will then restart. This process may take several minutes, as your printer will be restoring all of its settings back to the factory defaults.
Remember, performing a factory reset will often erase all of your personalized settings such as your Wi-Fi password and your system preferences.
If the above steps don’t work, you may want to try turning off your printer completely and unplugging it from the power source. Wait about 10 seconds then plug it back in to reset your printer.
If all else fails, try reaching out to Lexmark's customer service for further assistance.

As the process may vary slightly depending on the individual model and its software, always refer to the user manual accompanying the device for the most accurate information.

1. Ensure that the Lexmark MB2236adw printer is correctly set up and connected to your system. The printer can be connected via a wired or wireless network.
2. Place the document to be scanned on the scanner glass or load it into the Automatic Document Feeder (ADF).
3. Go to your computer, click on the "Start" menu then go to "All Programs". Find the "Lexmark" folder and select the "Lexmark Printer Home" application.
4. From the options provided, click on the "Scan" menu.
5. Choose the "send as" format, color, resolution, and other options as per your preference.
6. Click on the "Preview" button if you want to see how the document will look like after scanning.
7. If you are satisfied with the preview, click on the "Scan" button.
8. Choose where you want your scanned document to be saved on your computer then click "Ok".
Note: These steps may vary depending on your operating system and the exact model of your Lexmark printer. You can find more specific instructions in your printer's user manual or on the Lexmark support website.
If the printer doesn’t scan, make sure that it’s updated to the latest firmware, and the necessary drivers are installed on your computer. If the problem persists reach out to Lexmark technical support for help.

There could be several reasons why your Lexmark printer is not printing. Some common troubleshooting steps you can try are as follows:
1. Check the printer's connections: Ensure that the printer is properly connected to your computer or network. Verify if the cables are securely plugged in and that there are no loose connections.
2. Check paper and ink/toner levels: Make sure there is enough paper in the printer's tray and that the ink or toner cartridges have sufficient levels. Replace any low or empty cartridges if necessary.
3. Restart your printer and computer: Sometimes a simple restart can resolve various issues. Turn off both your printer and computer, wait for a few seconds, and then turn them back on.
4. Check for printer queue issues: Open the print queue on your computer and ensure that there are no stuck print jobs. If there are, try cancelling or clearing them and then attempt to print again.
5. Update printer drivers: Outdated or incompatible printer drivers can cause printing problems. Visit the Lexmark support website and download the latest drivers for your printer model. Install them on your computer.
6. Run a printer troubleshooter: Most operating systems have built-in printer troubleshooters that can help diagnose and fix common printer issues. Use the printer troubleshooter specific to your operating system.
7. Check printer settings: Make sure that the correct printer is selected in your computer's print dialog. Additionally, check the print settings to ensure they match your requirements.
8. Clear print spooler: If you are using a Windows computer, you can try clearing the print spooler. Open the Services menu, locate the Print Spooler service, right-click on it, and select "Stop." After that, navigate to the `C:\Windows\System32\spool\PRINTERS` folder and delete all the files in it. Finally, restart the Print Spooler service.
If none of the above solutions work, it may be necessary to contact Lexmark customer support for further assistance.