Iiyama PROLITE-GE2488HS-B1 user manual

To change the input on your iiyama ProLite GE2488HS-B1 monitor, you can follow these steps:
1. Locate the control buttons on your monitor. These buttons are usually placed on the front or bottom edge of the display.
. Press the Menu button to open the OSD (On-Screen Display) menu.
3. Use the arrow buttons (Up, Down, Left, Right) to navigate through the menu options.
4. Look for the Input or Source option in the OSD menu.
5. Once you have selected the Input or Source option, press the Menu button again to enter the submenu.
6. Now, you can use the arrow buttons to select different input sources such as VGA, DVI, HDMI, or DisplayPort.
7. After selecting the desired input source, press the Menu button to confirm your selection.
8. The monitor will then switch to the chosen input source.
Note: The button labels and menu options may slightly vary depending on the exact model of your iiyama ProLite monitor, but the general process should be similar.

To turn on your Iiyama ProLite GE2488HS-B1 monitor, you can follow these steps:
1. Locate the power button on the monitor. It is usually located on the front or the side of the monitor.
. Press and hold the power button for a few seconds until the monitor powers on.
3. Once the monitor is turned on, it will display the Iiyama logo or go straight to the input selection screen.
If the monitor does not turn on, make sure it is properly connected to a power source and that the power cable is securely plugged into the monitor and the power outlet. Additionally, check if the power outlet is working by trying a different device or plugging in the monitor to a different power outlet.

To connect your Iiyama ProLite GE2488HS-B1 monitor, follow these steps:
1. Ensure you have all the necessary cables: power cable, HDMI or DisplayPort cable (depending on your computer's video output), and any additional audio cables if required.
2. Turn off your computer and monitor before connecting any cables.
3. Locate the video output port on your computer. It could be HDMI, DisplayPort, DVI, or VGA, but for optimal quality, it is recommended to use HDMI or DisplayPort if available.
4. Connect one end of the appropriate video cable (HDMI/DisplayPort) to the corresponding port on the back of the Iiyama monitor.
5. Connect the other end of the video cable to the matching video output port on your computer.
6. If you need audio output from the monitor, connect the audio cable (usually 3.5mm audio jack) from the audio output on your computer to the audio input on the monitor.
7. Connect the provided power cable to the power input on the back of the monitor and plug the other end into a functioning power outlet.
8. Turn on the monitor using the power button.
9. Turn on your computer. The monitor should detect the video signal and display your computer's screen.
10. If the monitor does not automatically display anything or shows a "No Signal" message, try selecting the correct input source on the monitor's OSD (On-Screen Display) menu by pressing the appropriate buttons on the front of the monitor. The buttons and navigation vary depending on the specific model.
11. Adjust the display settings on your computer if necessary (resolution, refresh rate, etc.) to optimize the visual quality of the monitor.
With these steps, your Iiyama ProLite GE2488HS-B1 monitor should be successfully connected to your computer.

To unlock an iiyama ProLite GE2488HS-B1 monitor, you can follow these steps:
1. Locate the power button, which is typically positioned at the bottom-right corner of the monitor's front panel.
. Turn off the monitor by pressing and holding the power button until it powers off.
3. While the monitor is turned off, locate the "Menu" button on the front panel. It is usually positioned near the Power button.
4. Press and hold the Menu button for around 5-10 seconds.
5. While still holding the Menu button, turn on the monitor by pressing the power button.
6. Keep holding the Menu button for a few seconds until the OSD (On-Screen Display) menu appears on the screen.
7. Now, release the Menu button and navigate through the OSD menu using the other buttons on the front panel.
8. Look for an "Unlock" or "Lock" option in the OSD menu. Use the navigation buttons to select it.
9. Change the setting from "Lock" to "Unlock" if it's locked.
10. Once unlocked, exit the OSD menu by pressing the Menu button or the power button.
By following these steps, you should be able to unlock your iiyama ProLite GE2488HS-B1 monitor and adjust its settings as needed.