HP LASERJET-PRO-M148DW user manual

To perform a factory reset on your HP LaserJet Pro MFP M148fdw printer, follow these steps:
1. Make sure the printer is turned on.
. Press and hold the Cancel button on the control panel for about 5 seconds until the Ready light starts blinking.
3. Release the Cancel button.
4. Press and hold the Wireless and Info buttons simultaneously for about 5 seconds until the control panel display shows the "Reset menu" option.
5. Press the Cancel button to navigate to the "Reset menu."
6. Use the up and down arrow buttons to highlight the "Restore Factory Settings" option, then press the OK button.
7. The printer will display a warning message asking for confirmation. Use the up and down arrow buttons to select "Yes," then press the OK button.
8. The printer will proceed with the factory reset process. Wait for the printer to complete the reset, which may take a few minutes.
9. Once the reset is complete, the printer will restart automatically.
10. After the printer restarts, it will be restored to its factory default settings.
Note that performing a factory reset erases all custom settings and configurations, so you will need to set up your printer again as per your preferences.

To connect your HP LaserJet Pro MFP m148fdw to Wi-Fi, follow the steps below:
1. Ensure that your printer and Wi-Fi router are turned on and functioning properly.
. On the printer's control panel, press the "Wireless" or "Network" button to access the Wireless Menu.
3. Use the arrow keys to navigate through the menu options and select "Wireless Setup Wizard" or a similar option.
4. The printer will start searching for available wireless networks. Wait for the list of available networks to appear on the screen.
5. Select your Wi-Fi network from the list and press "OK" or "Enter."
6. If prompted, enter the Wi-Fi password using the on-screen keyboard. Ensure that the password is entered correctly.
7. After entering the password, press "OK" or "Enter" to confirm.
8. The printer will attempt to connect to the Wi-Fi network. This may take a few moments.
9. Once the Wi-Fi connection is established, the printer will display a confirmation message. You can also print a wireless network test report to verify the connection.
10. You can now use your HP LaserJet Pro MFP m148fdw wirelessly over the Wi-Fi network.
Note: Make sure that your Wi-Fi router is within range of the printer and the Wi-Fi signal is strong for optimal performance.

To set up your HP LaserJet Pro M148dw printer, follow these steps:
1. Unpack the printer: Remove all packaging materials and protective tapes from the printer.
2. Connect the printer to a power source: Plug one end of the power cord into the back of the printer and the other end into a power outlet.
3. Turn on the printer: Press the power button on the printer control panel to turn on the printer.
4. Adjust the control panel: Set the date, time, and language preferences using the control panel touch screen.
5. Install the toner cartridge: Open the front door of the printer, remove the toner cartridge from the packaging, and gently shake it side to side to distribute the toner. Insert the cartridge inside the printer until it clicks into place.
6. Load paper into the input tray: Slide out the paper input tray at the bottom of the printer. Adjust the paper guides to fit the paper and load it into the tray. Push the tray back into the printer.
7. Connect to a network (optional): If you want to connect the printer to your wireless network, press the wireless button on the printer control panel, then follow the prompts to connect to your network.
8. Install the printer software: Insert the CD that came with the printer into your computer or download the latest software drivers from the HP website. Run the installation program, and follow the on-screen instructions to complete the software installation.
9. Test the printer: Print a test page to ensure that the printer is set up correctly. You can do this from the printer control panel or from your computer.
Once you have completed these steps, your HP LaserJet Pro M148dw printer should be set up and ready to use.

I'm sorry, but I can't provide the password for a specific device like the LaserJet Pro MFP M148fdw. The password is typically set by the user or the administrator. You may need to refer to the device's manual or contact the manufacturer for assistance with resetting or retrieving the password.