HP ENVY-5660 user manual

Follow the steps below to reset the HP Envy 5660 printer:
1. Turn on your HP Envy 5660 printer if it isn't already turned on.
. Wait until the printer is in the ready state.
3. Simultaneously, press both the "Power" button and the "Start Copy Black" button from the printer's control panel (it is the first button from the left at the bottom row of the control panel)
4. Once you press these buttons together, immediately release both buttons.
5. Now, wait until the printer is in its initial state.
6. Once the printer gets silent and idle, wait for a while (approximately 60 seconds), and the printer will be reset.
Please note, these steps will reset your printer settings. You need to reconfigure your printer settings if you have made any custom settings previously.
Always remember to unplug the printer directly from the wall outlet and not from the back of the printer for safety purposes.

There could be several reasons why your HP ENVY 5660 printer is not printing in color. Here are a few possible causes and troubleshooting steps you can try:
1. Check ink levels: Ensure that the color ink cartridges have enough ink left. If they are low or empty, replace them with new cartridges.
2. Clean printhead: Use the printer's software utility to clean the printhead. This can help remove any clogs or dried ink that may be blocking the color ink flow.
3. Check print settings: Confirm that the print settings are not set to black and white or grayscale mode. Open the print dialogue on your computer and ensure that color printing is selected.
4. Update printer driver: Visit the official HP website and check if there are any updates available for your printer's driver. Download and install any updates, as outdated drivers can cause printing issues.
5. Verify paper type: Ensure that you are using the correct type of paper for color printing. Certain types of paper may not be suitable for receiving color ink, resulting in poor or no color prints.
6. Reset printer: Try performing a printer reset. Disconnect the power cord from the printer and the wall outlet, wait for a minute, and then reconnect it. Turn on the printer and attempt to print again.
7. Contact support: If none of the above steps resolve the issue, consider reaching out to HP customer support for further assistance. They may provide additional troubleshooting steps or advise you on getting the printer serviced if needed.

To print the configuration page on your HP Envy 5660 printer, you can follow these steps:
1. Turn on your printer and make sure it is connected to your computer or network.
. Load plain, white paper into the input tray of your printer.
3. From the control panel of the printer, tap on the "Wireless" icon or press the "Wireless" button to access the wireless settings.
4. Tap on the "Settings" option in the Wireless menu.
5. Scroll down and select the "Print Reports" option.
6. Locate and select the "Network Configuration Page" or "Wireless Test Report" option.
7. Tap on the "Print" button to begin printing the configuration page.
You can also print the configuration page using the HP printer software installed on your computer. Here are the steps:
1. Ensure that your printer is connected to your computer and turned on.
. Open the HP printer software on your computer.
3. Go to the "Print & Scan" or "Print & Fax" section, depending on your operating system.
4. Find your printer in the list of available printers and select it.
5. Locate the "Tools" or "Utilities" tab and click on it.
6. Look for an option like "Printer Toolbox" or "Device Configuration" and click on it.
7. In the printer toolbox or device configuration window, find and select the "Print Configuration Page" option.
8. Click on the "Print" button to print the configuration page.
By following these steps, you should be able to print the configuration page on your HP Envy 5660 printer.

To connect your HP ENVY 5660 printer to the Internet, follow these steps:
1. Ensure that your printer is turned on and in a ready state.
2. On the printer's control panel, touch the wireless icon or navigate to the Setup menu.
3. In the wireless settings, select Wireless Setup Wizard, and it will search for available networks.
4. Choose your Wi-Fi network from the list of available networks. If your network is not listed, select Enter New Network Name, and manually enter your network name (SSID) using the on-screen keyboard.
5. If your network is secured, you will be prompted to enter the network password or passphrase using the on-screen keyboard.
6. After entering the correct password, press Done or OK.
7. The printer will try to connect to your Wi-Fi network. The wireless light on the printer should become solid or blue to indicate a successful connection.
8. Once the printer is connected, you can confirm the connection by printing a network configuration page. On the printer's control panel, navigate to the Setup menu, and select Network Setup or Network Summary. Choose Print Network Configuration Page or a similar option.
9. The printed page will provide information about the wireless connection, including the IP address. You can use this IP address to manage your printer settings or access the embedded web server.
Your HP ENVY 5660 printer should now be connected to your Wi-Fi network, allowing you to print wirelessly from any connected device on the same network.