HP ENVY-4522 user manual

1. Connect the power cord.
Unpack the power cord from the box, plug one end into the back of the printer and the other end into a power socket.
2. Install the ink cartridges.
Open the ink cartridge access door at the front of the printer and wait for the carriage to move to the center. Remove the protective tape from the new ink cartridges and insert them into the matching slots. Close the door when done.
3. Load paper into the input tray.
Pull out the input tray from the bottom of the printer, load a stack of paper with the print side facing down, and adjust the paper width guide.
4. Power on the printer.
Press the Power button on the front of the printer. The printer will initialize.
5. Install printer software.
On the computer, visit the HP website, enter the printer model then follow the onscreen instructions to download the suitable driver compatible with your operating system. Run the setup file and follow the installation steps to install the software.
6. Connect the printer.
You can connect the printer to the computer or network. For a wired connection, connect the printer to the computer using a USB cable. For a wireless connection, go to the setup section on your printer’s control panel, select Network Setup, select Wireless Settings, and then select Wireless Setup Wizard. Follow the on-screen instructions.
7. Print a test page.
Finally, you should print a test page to verify that the printer is properly installed and in good working order.

NOTE: If the printer doesn’t work after these steps, contact HP customer support or refer to the printer's user manual for additional help.

Follow the steps below to connect your HP Envy 4522 printer to your computer:
1. **Unbox Your Printer:** Open the printer's box and remove the HP Envy 4522 printer from its packaging. Check for any other accessories such as the power cord, printer installation software CD, ink cartridges and the user guide.
2. **Power up Your Printer:** Connect the power cord of your HP 4522 printer to a wall outlet and then connect the other end of the cord to the printer. Push the power button on the printer to turn it on.
3. **Install the Ink Cartridges:** Open the ink cartridge door and insert the cartridges into the appropriate slots according to the color code. Close the ink cartridge door.
4. **Load Paper:** Open the supply tray and slide the paper width guide to the extreme left. Load enough paper on the tray and adjust the paper width guides.
5. **Install Printer Software:** Insert the printer installation CD into your computer's CD drive and follow the on-screen prompts to install the printer software. If you don't have a CD drive, you can download the software from the HP website.
6. **Connect the Printer to the Computer:** You can do this by either using a USB cable or connecting it wirelessly.
If you choose the wireless option, click on the wireless icon on the printer's control panel and then click on "Wireless Setup Wizard". Follow the on-screen instructions to connect to your wifi network. After the printer is connected to the wifi network, return to the printer software on your computer and continue the setup process.
If you choose to use a USB cable, simply connect one end of the cable to your printer and the other end to the computer.
7. **Complete the Setup:** Once the printer is connected, follow the remaining prompts to complete the installation. After the setup is complete, try printing a test page to make sure everything is working correctly.
Remember that both the computer and the printer should be connected to the same network if you are connecting wirelessly.

There could be several reasons why your HP Envy printer is not working. Here are some possible solutions:
1. Check power and connections: Make sure the printer is properly plugged into a power source and all cables are securely connected to both the printer and your computer or network.
2. Restart printer and computer: Try turning off both the printer and your computer, then turn them back on after a few minutes. This can help refresh the devices and resolve minor technical glitches.
3. Update or reinstall printer drivers: Outdated or corrupted printer drivers can cause issues. Visit the HP website, enter your printer model, and download the latest drivers for your operating system. Install them and see if it resolves the problem.
4. Clear print queue: Sometimes, a stuck print job can prevent other documents from printing. Open the print queue on your computer and cancel any pending print jobs. Then try printing a new document.
5. Check ink or toner: Ensure that there is enough ink or toner in the printer cartridges. If they are low or empty, replace them with fresh cartridges.
6. Paper jam or sensor issues: Open the printer and check for any paper jams or obstructions. Clean the printer rollers and sensors if necessary.
7. Network connection: If using a network-connected printer, ensure that it's connected to the correct Wi-Fi network and that both the printer and computer share the same network.
8. Run printer troubleshooter: Most operating systems have built-in printer troubleshooting tools that can help detect and fix common printer issues. Run the troubleshooter to identify any problems and apply the suggested solutions.
If none of the above solutions work, it may be worth contacting HP support or seeking professional assistance to diagnose and resolve the issue.

There could be several reasons why your HP Envy 4520 printer is not printing. Here are some common troubleshooting steps you can perform to determine the cause of the issue:
1. Check printer connectivity: Ensure that your printer is properly connected to your computer or network. If using a USB cable, check if it is securely plugged into both the printer and the computer. If using a wireless connection, make sure your printer is connected to the same Wi-Fi network as your computer.
2. Check printer status: Check if there are any error messages or warning lights on the printer. Resolve any hardware or paper jams issues, replace empty ink cartridges, or clear any error messages displayed on the printer's screen.
3. Restart devices: Power off both your computer and printer. Wait for a few minutes and then power them back on. Sometimes a simple restart can fix minor glitches.
4. Update printer drivers: Outdated or incompatible printer drivers can cause printing issues. Go to the HP website and download the latest drivers specific to your printer model. Install the drivers on your computer and then try printing again.
5. Check print queue: Verify if there are any pending print jobs in the print queue. Sometimes, a print job can get stuck and prevent other prints from completing. Clear the print queue and try printing again.
6. Check default printer setting: Ensure that your HP Envy 4520 is set as the default printer on your computer. If not, set it as the default and check if it resolves the issue.
7. Check printer settings: Make sure the printer settings, such as paper size, print quality, and orientation, are properly configured to match your print job requirements. Incorrect settings may prevent the printer from printing.
If you have tried these troubleshooting steps and your HP Envy 4520 printer still does not print, it may be necessary to contact HP support or a professional technician for further assistance.