Danby DDW621WDB user manual

The Danby DDW621WDB Countertop Dishwasher comes with the following settings:
1. Intensive: This setting is for heavily soiled crockery and resistant tableware like pots and pans.
2. Normal: This is the standard setting for everyday cleaning of dishes and cutlery.
3. Economy: Designed for lightly soiled dishes and cutlery, this setting runs a shorter cycle, using less energy and water.
4. Rapid: This is the quickest cycle and is designed for lightly soiled items needing a quick clean.
5. Soak: This option is used for dishes with tough, stuck-on food. It will soak the dishes in water, making the stains easier to remove in a later cycle.
6. Glass: This setting is for delicate items such as glassware. It uses a gentle wash and rinse cycle to avoid potential damage.
7. Auto: This option automatically detects the level of dirt on the dishes and adjusts the cycle accordingly to ensure optimal cleaning with efficient use of water and energy.
Please refer to the product user guide for specifics and additional information. Always follow the manufacturer's guidelines for loading dishes and using detergent to ensure effective cleaning and to protect your dishware.

To reset your Danby DDW621WDB countertop dishwasher, you can follow these steps:
1. Turn off the dishwasher by pressing the power button or unplugging it from the power source.
2. Wait for about 10-15 seconds to allow the dishwasher to fully shut down and reset.
3. Press and hold the "Start/Cancel" button for approximately 5 seconds.
4. While still holding the "Start/Cancel" button, plug the dishwasher back into the power source or turn on the power button.
5. Continue holding the "Start/Cancel" button for another 5 seconds until you see the display flash or hear a beep sound.
6. Release the "Start/Cancel" button, and the dishwasher should be reset.
After the reset, you can set up your desired program and options as needed. Make sure to consult your dishwasher's manual for specific instructions related to your model.

There could be several reasons why your Danby dishwasher is not working. Here are some possible causes:
1. Power supply: Ensure that the dishwasher is properly connected to a power source and that the circuit breaker or fuse is not tripped. Check if any other electrical appliances are working on the same power outlet to rule out any power supply issues.
2. Water supply: Confirm that the water supply valve is open and supplying water to the dishwasher. You may need to check if the water inlet hose is kinked or clogged, preventing water from reaching the dishwasher.
3. Door latch: The dishwasher door latch should be securely closed for the appliance to start working. If the latch is faulty or misaligned, it may prevent the dishwasher from starting. Try adjusting or replacing the latch if necessary.
4. Control panel or buttons: If the control panel or buttons are not responding, there may be an issue with the control board or a faulty connection. Check if any error codes are displayed, and consult the dishwasher's manual for troubleshooting guidance.
5. Drainage problems: Ensure that the dishwasher's drain hose is correctly installed and not clogged. A clogged drain hose or drain filter can prevent the dishwasher from draining properly, leading to operational issues.
If none of these suggestions solve the problem, it may be best to contact Danby's customer support or schedule a service appointment with a professional technician for further assistance.

There could be several reasons why your Danby Portable Dishwasher is not draining properly. Here are a few common causes and solutions:
1. Clogged Drain Hose: Check if the drain hose is kinked, twisted, or clogged. Remove any obstructions and ensure the hose is properly connected and not pinched.
2. Blocked Air Gap or Drain Filter: The air gap (if present) or drain filter may be blocked by food debris or mineral deposits. Clean the air gap and drain filter thoroughly to ensure proper drainage.
3. Faulty Drain Pump: The dishwasher's drain pump may be faulty or clogged. Inspect the pump for any blockages or damage. If necessary, clean or replace the drain pump.
4. Improper Sink Connection: Ensure that the dishwasher's drain hose is correctly connected to the sink drain or garbage disposal unit. If not properly connected, it can impede the drainage process.
5. High Drain Loop: Make sure the dishwasher's drain hose is installed with a "high drain loop" to prevent backflow of water from the sink into the dishwasher.
If none of these solutions resolve the issue, it may be best to contact a professional technician or Danby customer support for further assistance.